We have been doing M.2 drives just fine without adding storage controller drivers. Make sure you are using the latest WinPE and ADK.
Mark Kent Manager, Client Systems Engineering Technology Support Services Resources for Information, Technology and Education (RITE) http://rite.buffalostate.edu<http://rite.buffalostate.edu/> From: listsad...@lists.myitforum.com [mailto:listsad...@lists.myitforum.com] On Behalf Of Thelen, Chris Sent: Thursday, May 25, 2017 8:10 AM To: mssms@lists.myitforum.com Subject: RE: [mssms] m.2 and win10 OSD Dell creates and releases WinPE drivers that you can import into your boot image. We are a Dell shop and I’ve been doing this for years and have never had it not work with any of their models. But keep in mind, when Dell releases new models of laptops and desktops, you may need to come back to this link and update the WinPE drivers. http://en.community.dell.com/techcenter/enterprise-client/w/wiki/2065.dell-command-deploy-driver-packs-for-enterprise-client-os-deployment From: listsad...@lists.myitforum.com<mailto:listsad...@lists.myitforum.com> [mailto:listsad...@lists.myitforum.com] On Behalf Of Morris, Spencer Sent: Thursday, May 25, 2017 7:04 AM To: mssms@lists.myitforum.com<mailto:mssms@lists.myitforum.com> Subject: RE: [mssms] m.2 and win10 OSD Mike, it sounds like you’re missing storage drivers. Give this a try: Put a pause right before format and partition disk - http://kjaerit.com/?p=297 Copy the two storage drivers to a usb stick - iaAHCIC.inf and iaStorAC.inf Open up a command prompt and try to load one of the drivers then run disk part, whichever one makes the disk show up will be the one you will want to add to your boot image. From: listsad...@lists.myitforum.com<mailto:listsad...@lists.myitforum.com> [mailto:listsad...@lists.myitforum.com] On Behalf Of Mike Dougherty Sent: Wednesday, May 24, 2017 11:55 PM To: mssms@lists.myitforum.com<mailto:mssms@lists.myitforum.com> Subject: Re: [mssms] m.2 and win10 OSD m.2 is a drive form factor, not necessarily a drive "communication" type. is the m.2 drive NVMe? or sata? is the machine itself configured for UEFI booting? Legacy Boot/CSM support? SecureBoot enabled? is there an NVMe setting in the bios/setup? does the system/BIOS itself recognize a hard drive is attached? the fact that diskpart doesn't list a drive in winpe when you run it indicates you're either missing winpe drivers/bios settings or you have bad hardware. what version of the ADK are you running? have you updated the drivers in your boot media recently? On Wed, May 24, 2017 at 5:34 PM, Michael K Murray <mmur...@csuchico.edu<mailto:mmur...@csuchico.edu>> wrote: Hey folks, We’re trying to image an OptiPlex 7050 that has a 500GB m.2 card. It gets to the partition step and fails, as it doesn’t recognize any disk. Running diskpart at a command prompt shows no disks. I’ve Googled like crazy, but only seem to find Windows 7 articles. We’re trying to image with Win10. Log attached. Best Regards, Mike Murray Desktop Engineer/IT Consultant - IT Support Services California State University, Chico 530.898.4357<tel:(530)%20898-4357> mmur...@csuchico.edu<mailto:mmur...@csuchico.edu> Remember, Chico State will NEVER ask you for your password via email! For more information about recognizing phishing scam emails go to: http://www.csuchico.edu/isec/basics/spam-and-phishing.shtml [2016 Design Firm of the Year] [WRA 100 Years] The information supplied in this message may be privileged, confidential and/or exempt from disclosure under applicable law. If you are not the intended recipient of this message, the sender does not intend delivery to you to waive any privilege or right pertaining to this message. You have no right to retain, disseminate, copy or disclose the material contained herein. If you have received this message in error, please immediately notify the sender by return e-mail, and delete the errant message. Thank you. WRA_Disclaimer_v20070222a
