Re: [Elecraft] Filter alignment, once more with gusto!

W3FPR - Don Wilhelm wrote: John, For filter alignment with Spectrogram, you should be using a source of broadband noise at the K2 antenna input (like the Elecraft N-Gen or 'dead-band' noise). Hello John, While you have Spectrogram going take a check of how you have L34 set. I've bee

[Elecraft] FS: Elecraft K2/100 S/N 04266

Beautiful and like new Elecraft K2/100 S/N 04266 (2.04 1.09, Rev “B”) built new in March of 2004. If you’ve been looking for a VERY nice assembled K2 this is the one. This K2 has only resided here in the shack. The following options are installed: KPA100 – 100 Watt Option KSB2-

[Elecraft] Elecraft CW Net Announcement

Good Evening, A long week should be followed by a bit of rest. Tomorrow afternoon seems convenient. How many of you would like to participate in the weekly Elecraft CW Nets? All are welcome. The bands appear to be happy transporting a bit of RF around the world. The FISTs folks are send

Re: [Elecraft] QRP Pwr/VSWR meter

Check out my E-Meter at www.telepostinc.com/n8lp.html I am getting very close to offering a kit version of it. A comprehensive article will also be published in QEX in the near future if want to homebrew your own. They accepted my manuscript a few weeks ago, but haven't given me the publicatio

[Elecraft] 5w K7LOW begins next hour in C2C

The "2004 Coast to Coast FISTS Club Event" begins next hour; the central Oregon's coast QRP Club station K7LOW will be active on frequencies between 14.057 - 14.059 and also 7.058MHz. K7LOW calling CQ C2C on K2 s/n 586... Details of the event are at: http://www.tomochka.com/k7fff/fnw_c2c04.html

Re: [Elecraft] QRP Pwr/VSWR meter

Just what Don said. I have both, I use both, and I love both. The two kits are a snap to build and Marshall supports his products VERY well. 73, Bob WA4FOM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post

Re: [Elecraft] QRP Pwr/VSWR meter

Hi I use a OHR WM-2 qrp wattmeter http://www.mtechnologies.com/ohr/wattmeter.htm It is available as a kit or assembled and I have found it to be accurate and reliable. I use it just about all the time to align all the Elecraft products. OHR also

[Elecraft] QRP Pwr/VSWR meter

Can someone point me to info on QRP pwr/vswr meters? Thanks, Fred K6DGW Auburn CA CM98 ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://ma

RE: [Elecraft] HALP! K2/100 and KIO2 seem DEAF to serial comms.

What happens when you try HyperTerminal? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Hel

[Elecraft] HALP! K2/100 and KIO2 seem DEAF to serial comms.

Hi Folks: Posting this to both the Elecraft and the TRLOG reflectors, in the hop that someone can assist. Not sure if it's a TRLOG or an Elecraft (or OPERATOR) problem. Interesting failure here... one which also occurred the morning of Field Day 2004 (perfect timing, right?). When running

Re: [Elecraft] Re: Mod for more AF gain on K2

At 11:00 PM 10/22/2004, wayne burdick wrote... >I tame the noise by putting a resistor/capacitor network in series between >pins 5 and 8. Perhaps a "real" LM386 has more noise. Noise in the NJM386B I used measured ~20 mV p-p in the absence of signal (AF pot at min, measured at the speaker). Tha

Re: [Elecraft] Help needed

In view of what you said, Snip "When Antenna 2 is selected without any antenna connected to it, I push to tune button to try to tune it on 7Mhz band three times. Now there is not any output on 7 Mhz and only 3 watts output on 10 Mhz." if this is what you meant, then by all means hook an anten

[Elecraft] Help needed

Hi, My K2 serial number is 4288 with all options installed, except 100 Watts module. When Antenna 2 is selected without any antenna connected to it, I push to tune button to try to tune it on 7Mhz band three times. Now there is not any output on 7 Mhz and only 3 watts output on 10 Mhz. bu

Re: [Elecraft] Hakko 808

- Original Message - .I would steer clear of using pipes...It will not allow good air circulation and might lead to early heater failure and tip burning due to overheating...Just my thoughts...73 Jerry and all, Since the heater in the Haako is temperature controlled, I do not have

[Elecraft] Hakko 808

Several manufacturers sell the "coiled spring" type of soldering iron holder...I have seen them in RS too...If this type stand is too "tippy", it can be screwed onto a small board...I have an old heavy duty holder made by Hexacon that stands by itself...I would steer clear of using pipes...It wi

[Elecraft] For Sale K2 + extras

I have for sale my spare K2 (serial # 4278) This has the SSB option and 160M option, with the MH2 elecraft Mike. All in excellent (as new) condition and ready for shipping. Asking $650US or best offer or equivalent local funds, plus about $40 postage (e-mail for costs to other countries). Pleas