Hi Karl,
A question. Does the K2 have a variable resistor at R! Compression
ratio set?
Yes, the resistors RP5 are the 'variable' resistors for compression.
Yesterday I had send a mode for other compressions. With other resistors
you make your own three compressions.
73/72 de
Karl-Heinz Kaatz, DF7KHK wrote:
Hi Karl,
A question. Does the K2 have a variable resistor at R! Compression
ratio set?
Yes, the resistors RP5 are the 'variable' resistors for compression.
Yesterday I had send a mode for other compressions. With other
resistors you make your own three
Karl Larsen [EMAIL PROTECTED] wrote:
Hi Geoff, cut your weeds and we can both think hard on what Speech
Compression really is. I got to thinking and about all it can be is
clipping of the high voice peaks, and increasing audio drive. I will look
at the ARRL Hand Book and see what they
I've posted a chart at the link below that compares the best AA chemistry
(Lithium) to a pair of rechargeable LiPo batteries that are perfectly sized
to fit in the same space inside the KX1's lower case. I also periodically
took RF output readings of the rig during various points on the
Bill NY9H [EMAIL PROTECTED] wrote:
I too would be interested to see how much additional distortionless
average amplitude could be generated beyond the AD chip.
FWIW my guess is that if audio compression and true clipping is to be
The nylon screw is the ultimate answer...The reason the short occurs is that in
some instances the tapered head of the screw comes into contact with the sides
of the hole in the tab of Q6...Counter sinking the hole in the tab of Q6 works
as a temporary measure, but I would not recommend it as a
For some time I had been aware of the Rework Eliminator kit from Unpcbs for use
in the K2. At the time I could see no real use for me. However having built my
K2 and used it for some time I felt I wanted to restore it to its original
state to carry out some initial alignment checks and compare
I agree wholeheartedly. I recently had problems with the KSB2 and 160 meter
mods. It was great to be able to do A/B comparisons and troubleshooting simply
by unplugging the offending module and plug in the header PCB.
Mike
AI4NS
For some time I had been aware of the Rework Eliminator kit from
Hi
Having successfully build a K1 and a KX1, I have finally bitten the bullet
and gone for the fully monty. My new K2 is going together fine, except I
can't find the 82 pf capacitors C71 C174. I know Elecraft will send them
to me, but I would like to keep up my momentum. I live in the greater
Fellow builders,
I've been working on building my K2 as time permits since may of 2005.
I was hoping to have it completed by now, but got stuck on a problem and
haven't had the time to really delve into it until recently.
Back in 2005, I posted a question to the group - the topic was No Audio
if theres anyone in need of a quad matched set of theres rf power transistors
(2sc2879) i have a set for sale on ebay 2800274302 i will ship to the usa
i had them as a spare set for a als500m moble amp or for 2 sets for kpa100
thanks chris g0wfh k2-4980
John Harper wrote:
I've posted a chart at the link below that compares the best AA
chemistry (Lithium) to a pair of rechargeable LiPo batteries that are
perfectly sized to fit in the same space inside the KX1's lower case.
Do I really want to put an LiPo battery *inside* my KX1? When I used
Has anyone had any luck using the AWG Packet Engine software for HF packet
with their K2? I just cannot seem to get tuned in well enough to decode
packets. Even on the OP1 filter, I am thinking that I am just to close to
the edge of the bandwidth of the filter to receive. Any ideas?
73, Bill
On Sun, 10 Sep 2006 16:12:08 -0400, Treat Hull
[EMAIL PROTECTED] wrote:
Hi
Having successfully build a K1 and a KX1, I have finally bitten the bullet
and gone for the fully monty. My new K2 is going together fine, except I
can't find the 82 pf capacitors C71 C174. I know Elecraft will send
Oops, AGW not AWG ...
Has anyone had any luck using the AGW Packet Engine software for HF packet
with their K2? I just cannot seem to get tuned in well enough to decode
packets. Even on the OP1 filter, I am thinking that I am just to close to
the edge of the bandwidth of the filter to receive.
Do I really want to put an LiPo battery *inside* my KX1? When I used one,
I specifically put a pigtail and coax pwr connector on it to keep it
outside (and thus be able to fling it overboard if it burst into flames).
Fred K6DGW
KX1 #897
Fred, I don't know if you do or not. I guess you'll be
Zac,
If D9 has DC Voltage on the cathode, either there is RF on your antenna or
you have something wired wrong. Does the voltage at the cathode of D9
remain if you disconnect the antenna? Do you have any DC voltage on the
anode of D9? That should be zero volts.
Are you certain the K2 is not
Can't help on the AWG engine, but I'm able to use RTTY and Slow Scan TV ( At
least receive). I'm using the MMSCTV and MMpkt drivers. They are a sound
card implementation.
I enabled the RTTY mode -- the 'r' mode using the secondary menu commands.
Using Spectrogram, I set the filters fairly
Looking for a KAF2 that might be surplus to your needs. A friend of
mine just purchased a K2 and is looking for the audio filter.
Contact Len, K6LEC: [EMAIL PROTECTED]
Thanks,
Don Minkoff
NK6A
K2
K1
KX1
___
Elecraft mailing list
Post to:
John Harper wrote:
Fred, I don't know if you do or not. I guess you'll be flinging your
laptop and cell phone along with it as they use lithium chemistries as
well...
OK. Nothing against the battery chemistry ... God knows, Chemistry was
my very absolute second worst subject in college,
Sorry Folks,
I just got home and need to get chores done before work tomorrow
morning. I'll write the net report tomorrow evening.
I was surprised at good reports from my low antenna. The most interesting
contact was Beaverton though :) The folks at the picnic mostly did not
I'm getting ready to upgrade my K2 firmware to version
2.04. According to the instructions, I believe I will
have to manually reenter all of my menu and filter
settings once I install the new cpu. The instructions
say write all the info down, which is going to be time
consuming and which will
22 matches
Mail list logo