[Elecraft] Heil Proset Headphones

I am looking at picking up a second Headset Mic - DX chasing and contesting. What is the difference between the Heil Proset PS 6 and the Heil Proset K3 headsets for the K3 & K3S radios? Happy New Year Thanks, Irwin KD3TB -- Irwin KD3TB

Re: [Elecraft] Heil Proset Headphones

Irwin, The main difference is in the microphone element. The PS-6 has the Heil HC-6 element which is a wide range dynamic element which has a relatively low output. The ProSet-K2/K3 uses an electret element which has a high output level - it needs to have bias turned on. The K3/K3S is quite

Re: [Elecraft] W1

Ed - What are you putting the output power to -- a dummy load or an antenna? Do you have the KAT internal antenna tuner? If there is an SWR on the antenna line that the KAT is tuning out for the transceiver, then the W1 will read forward power and reverse power on the antenna line whereas the

Re: [Elecraft] W1

I performed some additional research, Johnny, VR2XMC, measured TP1 V at 4.82 back in December 2006. Maybe the 4.5 is a typo and should be 4.8: http://elecraft.365791.n2.nabble.com/some-questions-of-W1-td442330.html John KN5L On 12/31/2015 06:22 AM, John Oppenheimer wrote: > Hi Ed. > > The W1 DC

[Elecraft] W1

It is probably necessary to restate my question with more precision. 1. I have calibrated the K3s using Elecraft K3 Utility 2. I have carefully calibrated the W1 using the DDM method with a good quality DDM. 3. Comparing the results, I see that the W1 consistently calculates

Re: [Elecraft] W1

Hi Ed. The W1 DC voltage calibration resulted with incorrect reading with my W1. My hunch is that components have changed since Elecraft established the TP1 DC calibration voltage almost a decade ago. I have a KX3F with unchanged factory power calibration. Based on comments from Wayne, the KX3

Re: [Elecraft] Elecraft gear relative IMD

Pre-distortion dsp processing on the tx signal makes a DRAMATIC improvement. Check out the tx spectrum and waterfall outside the filter passband on this video before and after W1AEX switches in pre-distortion at 34 seconds in: https://www.youtube.com/watch?v=MCm3mKHyuAo 73/HNY, Barry N1EU On

Re: [Elecraft] Heil Proset Headphones

I went from the Heil mic/headset to the Yamaha CM-500 couldn't tell any difference except the money I saved. 73 Tex ka5y -- View this message in context: http://elecraft.365791.n2.nabble.com/Heil-Proset-Headphones-tp7612074p7612075.html Sent from the Elecraft mailing list archive at

Re: [Elecraft] Elecraft gear relative IMD

Two different animals. Harmonics and spurs are regulated by the FCC to be at least -43dB down on HF and -60dB down on 6 meters. The K3(s) meets those specs easily as evidenced by a couple of QST reviews. IMD is not regulated I think because most hams don't have the test equipment to pull it

[Elecraft] 30% discount on KE7X books at Lulu 12/31 only

I just check on what Lulu is offering for discounts and 30% on print books is pretty good. Only today, though. https://www.lulu.com/shop/search.ep?keyWords=elecraft= 73 and HNY all, Fred KE7X www.ke7x.com __

Re: [Elecraft] W1

Just wondering. Why is an accuracy within less than 1dB important? Happy New Year. 73, Bob Nobis - N7RJN n7...@nobis.net > On Dec 31, 2015, at 09:42, Ed Lambert wrote: > > John, > > Thank you for your response. > My original K3s test setup was per the manual: good

Re: [Elecraft] FAQ for K103B

Try the letter I instead of the number 1. On 12/31/2015 9:01 AM, Gene wrote: I tried the "K103BUPKT FAQ" link and it does not seem to work. Has any one the same problem? Thanks. Gene, W2BXR __ Elecraft mailing list Home:

Re: [Elecraft] Elecraft web site

Hmmm…. The site is not responding here in EPA as well. FiOS service, using a Mac Book. There’s been a lot of wonky internet things of late. Maybe it’s overload due to the holiday break…. or the CME. 73 de Ray K2ULR KX3 #211 > On Dec 31, 2015, at 1:09 PM, Bill OMara via Elecraft >

[Elecraft] Elecraft Website

I am still unable to connect to the Elecraft website. I have re-booted, cleared everything that I know of and re-booted the modem. Any ideas? I have Verizon FIOS and do not have any other sites that I cannot connect to (that I know of). Bob W6VY

Re: [Elecraft] Elecraft Website

We only need a couple of more States to respond and we'll have WAS !! HI HI 73 es HNY, Dick, W1KSZ -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Robert Nobis Sent: Thursday, December 31, 2015 12:52 PM To: Robert Dorchuck Cc:

[Elecraft] FAQ for K103B

I tried the "K103BUPKT FAQ" link and it does not seem to work. Has any one the same problem? Thanks. Gene, W2BXR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

Re: [Elecraft] KIO3B Audio Spec

Hi, Here is the spectrum out of the USB codec with a -73dBm carrier from the XG3: http://ab2tc.com/new_k3s_usb.png The K3S setting is USB with a passband of 300 to 2400Hz. I left the LINE OUT level set to the factory setting (10), and set the recording level with the Windows mixer (Win7).

Re: [Elecraft] KIO3B Audio Spec

Hi again, BTW, some people have been complaining about 60Hz hum in the audio. I zoomed in one the low end: http://ab2tc.com/k3s_usb_lows.png There is absolutely no sign of 60, 120 or 180Hz in this spectrum. I have also listened to the signal with good headphones and hear no trace of hum.

Re: [Elecraft] New K3S can't/won't talk to the K3 Utility

John, You first have to click on the "Copy New Files From Elecraft" button to load the files into your computer. After they download, you should see the information in the "Firmware Revisions" section. You should see the list of what is installed in your K3S as well as what is Available. If

[Elecraft] FW: W1

John, Thank you for your response. My original K3s test setup was per the manual: good quality dummy load (not the DL1 because of its 20 watt upper limit) with the ATU off. My high quality dummy load does not have a test point. After reading your results, I decided to take the DL1 as my "truth

[Elecraft] New K3S can't/won't talk to the K3 Utility

New K3S arrived, seems to work fine as a radio. Came set for CONFIG:USB, connect Elecraft USB cable to Win 7 laptop, all drivers seemed to down load OK. But when I start up K3 Utility, I get a COM Port 5 connection but will only say "K3 waiting for firmware load: RS232 speed 38400 bit/s"

Re: [Elecraft] OT: Access to Elecraft website

Some kind of cyber attack against the BBC this morning (GMT) 73 de David, M0XDF > On 31 Dec 2015, at 18:46, Ken G Kopp wrote: > > Access from Montana via CentutyLink has yet to fail. > > 73 - K0PP > __ > Elecraft

Re: [Elecraft] 30% discount on KE7X books at Lulu 12/31 only

Rats ! I tried to purchase the eBook version of the KX3 book. I live in Africa, and shipping more than doubles the cost of the printed book, so I wanted to buy and download the PDF version. I entered your code, but it tells me that the discount is only applicable to the printed version. I was

Re: [Elecraft] Elecraft Website

I have accessed the Elecraft web site several times today, with no issues. 73, Bob Nobis - N7RJN n7...@nobis.net > On Dec 31, 2015, at 12:22, Robert Dorchuck wrote: > > I am still unable to connect to the Elecraft website. I have re-booted, > cleared everything that I

Re: [Elecraft] KIO3B Audio Spec

In Knut's plot with the 1 kHz peak, the 2nd harmonic and 3rd harmonic are clearly visible. In the one with the low end, I agree, no 60 Hz, 120 Hz or 180 Hz is seen. I measured my K3S with the radio connected to the computer via the USB port. No 60 Hz, 120 Hz or 180 Hz signal observed. I

Re: [Elecraft] [Elecraft_K3] Re: Heil Proset Headphones

The Elecraft Pro Set is essentially a duplicate of the Heil IC Pro Set. The IC version of the Heil was, as I understand it, introduced as a suggested model for Icom radios (thus the "IC" designation), and has an electret cartridge. Electrets apparently work quite well with Icom gear, and they

[Elecraft] KI03BUPKT FAQ

I got the PDF file OK now. Thanks for the quick response fellows Gene w2BXR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

Re: [Elecraft] Elecraft web site

http://www.elecraft.com/elecraft_products_page.htm works for me. 73 Bob, K4TAX On 12/31/2015 12:09 PM, Bill OMara via Elecraft wrote: I'm also having a problem getting to Elecraft Web page. It's the only site I can't get too. I tried resetting the router and it still doesn't work.

Re: [Elecraft] 30% discount on KE7X books at Lulu 12/31 only

Rats! Forgot to include the code: NEWYEAR30 HNY, Fred From: KarlErb Sent: Thursday, December 31, 2015 11:41 AM To: Cady, Fred Subject: Fwd: [Elecraft] 30% discount on KE7X books at Lulu 12/31 only Tempting - but there's no mention of a

Re: [Elecraft] Elecraft web site

Nah! Have K-Line & KX3 w/PA and the Elecraft site loads fine. If clearing cache, rebooting computer & router don't help, then it may be a DNS issue for some reason . Use 63.249.121.83 to bypass DNS. 73 George AI4VZ -Original Message- From: kg9hfr...@gmail.com Sent: Thursday, December

Re: [Elecraft] W1

“Because it’s there.” George Leigh Mallory, 1923, answering the question why he continued to try to climb to the summit of Mt. Everest. 73, Lew N6LEW > On Dec 31, 2015, at 8:51 AM, Robert Nobis wrote: > > Just wondering. Why is an accuracy within less than 1dB important? >

Re: [Elecraft] Elecraft gear relative IMD

On Thu,12/31/2015 4:34 AM, Kevin Stover wrote: IMD is not regulated It is, as part of the wording of regulation of transmitted bandwidth, but the wording doesn't include numbers. The regulation states (I'm paraphrasing from memory) that the bandwidth of the transmitted signal shall be no

Re: [Elecraft] Elecraft web site

I'm also having a problem getting to Elecraft Web page. It's the only site I can't get too. I tried resetting the router and it still doesn't work. Bill W4RM Please use w...@aol.com as my primary account -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On

Re: [Elecraft] KIO3B Audio Spec

You'll get hum if your computer and K3 chassis aren't at the same ground potential. For many, it may be preferable to use the rear panel Line Out, which is transformer isolated. 73, Barry N1EU On Thu, Dec 31, 2015 at 2:15 PM, ab2tc wrote: > Hi again, > > BTW, some people have

Re: [Elecraft] Elecraft web site

I think it is only open to folks that do not have any Elecraft equipment. de kg9h > On Dec 31, 2015, at 12:27 PM, Ray Sills wrote: > > Hmmm…. The site is not responding here in EPA as well. FiOS service, using a > Mac Book. > > There’s been a lot of wonky internet

[Elecraft] OT: Access to Elecraft website

Access from Montana via CentutyLink has yet to fail. 73 - K0PP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

Re: [Elecraft] Elecraft Website

Working fine in Ohio... win7 64 bit with Chrome! David Koch wrote: > Just in case we haven't got Texas on the list, I am also using FIOS and > just checked with a couple different browsers and am also unable to > access the Elecraft web site. > > 73, Dave, W8OV > >

Re: [Elecraft] W1

For the same reason I find the AUTO SPOT function to be in error some 2 Hz. 73 Bob, K4TAX On 12/31/2015 3:36 PM, Gary Smith wrote: Because accuracy is or isn't. 73, HNY Gary KA1J __ Elecraft mailing list Home:

[Elecraft] (K3/K3S). Eliminate the 4 sec diddle with FSK-D and KY commands with n1mm??

Sent from my iPhone ...nr4c. bill __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net

Re: [Elecraft] 30% discount on KE7X books at Lulu 12/31 only

Sorry Ray. I just stumbled onto the discount. There is a website http://www.retailmenot.com/view/lulu.com that lists them. I have no idea why Lulu does things the way they do but the product is nice. 73, Fred From: Elecraft

Re: [Elecraft] Elecraft web site

Hi George: Here, in EPA with a Verizon FiOS account, even the IP address is not working. I’m thinking that Verizon is trapping the domain name and the address. Annoying, for sure. Glad I don’t need to download any firmware tonight. 73 de Ray K2ULR KX3 #211 > On Dec 31, 2015, at 2:42 PM,

Re: [Elecraft] Elecraft web site

Never ascribe to malice what can be explained by stupidity. On 12/31/2015 2:54 PM, Ray Sills wrote: I’m thinking that Verizon is trapping the domain name and the address. __ Elecraft mailing list Home:

Re: [Elecraft] KIO3B Audio Spec

Bob and all, Bonding to a common point may not cure hum and buzz. Follow the advice of Jim Brown K9YC and bond from equipment to equipment - following the path of the shields on unbalanced audio cables and RF coax. In other words, bond from the computer to the K3 (or from the computer to any

Re: [Elecraft] KIO3B Audio Spec

On Thu,12/31/2015 6:11 PM, Doug Person via Elecraft wrote: I've always believed in the star approach and completely agree with the series circuit issue. Physics is not a matter of belief. I suggest that you study my tutorial. 73, Jim K9YC

Re: [Elecraft] KIO3B Audio Spec

Hi Bob, Yes, the harmonics are visible but down a comfortable more than 70dB below the fundamental. There is still a little bit of junk around 3900Hz (it was there on the analog line out, too). AB2TC - Knut PS. Is a schematic forthcoming any time soon? This is the first radio I have owned

Re: [Elecraft] Elecraft Website

Bob, Elecraft site comes up fine here, south of Tacoma, WA. Using Comcast cable. URL I use is http://www.elecraft.com/, then just work through the site. When I have a connection problem, I usually just unplug the power to both my router and modem. Let them sit about a minute or so, then power them

Re: [Elecraft] W1

Because accuracy is or isn't. 73, HNY Gary KA1J > Just wondering. Why is an accuracy within less than 1dB important? > > Happy New Year. > > 73, > > Bob Nobis - N7RJN > n7...@nobis.net > > > > On Dec 31, 2015, at 09:42, Ed Lambert wrote: > > > > John, > > > >

Re: [Elecraft] KIO3B Audio Spec

Or simply make sure the radio and computer cases are connected with an adequate bond. Why would anybody choose not to? On 12/31/2015 1:29 PM, Barry N1EU wrote: You'll get hum if your computer and K3 chassis aren't at the same ground potential. For many, it may be preferable to use the rear

[Elecraft] (K3/K3S). Eliminate the 4 sec diddle with FSK-D and KY commands using n1mm??

I'm trying to set up n1mm for the RTTY contest. I'm attempting to use KY commands and all is well except I can't get rid of the annoying 4 seconds of trailing fiddles at the end. Yes, I've tried adding a {RX} at the end, I've tried every iteration of the "|" as is used in the K3 memories. I

Re: [Elecraft] Elecraft web site

Works fine here in nawthrun Vuhginya (thru Exede/Wild Blue Satellite). 73, Charlie k3ICH -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ray Sills Sent: Thursday, December 31, 2015 1:27 PM To: Elecraft Reflector

[Elecraft] Network

Hi For those complaining about lost access to the Elecraft site just note that the "WHAT'S APP" app on the i-phone has crashed worldwide according to news just in! __ Elecraft mailing list Home:

Re: [Elecraft] KIO3B Audio Spec

Yes, this is correct. I have all of my station equipment bonded to the common point on the station power supply. And I do not use any "ground" to the outside world from my 2nd floor station. Works just great, all bands 160M - 23 cm, any power level to legal limit, any mode. 73 Bob, K4TAX

Re: [Elecraft] KIO3B Audio Spec

Don et al: Well Jim and I are at 100% opposite positions on this point. Bonding from equipment to equipment is a series circuit in which the voltage divides across each value of R. Thus none of the equipment will be at zero potential. By using a bond conductor from each piece of equipment

Re: [Elecraft] Elecraft gear relative IMD

Being New Years Eve, it is nostalgia time, and I think it appropriate to discuss those antique stations. If you want to hear how bad some of those antique transmitters were, do listen tonight for SKN. Bad chirps, bad keyclicks and lots of phase noise that spread the signals out over a large

Re: [Elecraft] Elecraft Website

Just in case we haven't got Texas on the list, I am also using FIOS and just checked with a couple different browsers and am also unable to access the Elecraft web site. 73, Dave, W8OV On 2015-12-31 14:12, Richard W. Solomon wrote: We only need a couple of more States to respond and we'll

Re: [Elecraft] 30% discount on KE7X books at Lulu 12/31 only

Hi Fred, Do you happen to know the coupon code? 73, Scott N9AA On 12/31/15 11:01 AM, Cady, Fred wrote: I just check on what Lulu is offering for discounts and 30% on print books is pretty good. Only today, though. https://www.lulu.com/shop/search.ep?keyWords=elecraft= 73 and HNY all,

Re: [Elecraft] Elecraft web site

Working fin on my iPhone in NZ. Scott N0HOK / ZL1CHM Auckland New Zealand Sent from my iPhone On 31/12/2015, at 11:00 AM, Lewis Phelps wrote: > No problem accessing Elecraft.com the web site here. > > Mac, Safari browser. Pages load instantaneously. > > Lew > N6LEW > >

Re: [Elecraft] Elecraft Website

Have had no trouble reaching Elecraft web site from Aurora, Colorado during past two days. 73, N0RRL Lee On Thu, Dec 31, 2015 at 2:17 PM, Richard S. Leary wrote: > Bob, > Elecraft site comes up fine here, south of Tacoma, WA. Using Comcast cable. > URL I use is

Re: [Elecraft] Elecraft Website

No problems from rural Colorado using satellite. FYI, there are a lot of players involved in transporting web data from a server to your browser. Sometimes a given url will get blacklisted because something suspicious was detected. These false alarms usually clear up in an hour or 2. Be

Re: [Elecraft] Elecraft gear relative IMD

On Thu,12/31/2015 3:07 PM, Ron D'Eau Claire wrote: The same is true for Ham rigs. It's perfectly okay to run an old Heathkit AT-1 or a 1930's homebrew rig with cathode keying today as it was back then, even though the keying bandwidth will be substantially greater than modern rigs. WRONG! The

[Elecraft] Elecraft website

I just brought up the website on my iPad using first Hughesnet satellite internet and then with Verizon. Both worked fine. Sid Frissell, NZ7M Sent From Sid Frissell's iPad __ Elecraft mailing list Home:

Re: [Elecraft] [TenTec_Eagle] Eagle and SKN

Thanks for the reminder ! I have my J38 hooked up and ready. It will be fun . My fist with the straight key is pretty bad. I wont get any respect tonight hihi 73, Bob K6UJ Sent from my iPhone > On Dec 31, 2015, at 3:58 PM, Bob McGraw - K4TAX wrote: > > Remember

Re: [Elecraft] KIO3B Audio Spec

Zero potential is not necessarily the criteria that is to be achieved. The important point is that adjacent pieces of equipment be at the *same* potential, whether that be at zero or 100 volts potential. OK, that is an extreme example, but the point is that there should be a low resistance

[Elecraft] WTB KIO3B

If someone is upgrading to the new KIO3BUPKT board I'm interested in buying your old board. Seems my KIO3B board has lost the band data capability. Please contact me directly (ron.e.spen...@gmail.com) as I don't want to clutter up the reflector with replies. Thanks Ron N4XD

Re: [Elecraft] 30% discount on KE7X books at Lulu 12/31 only

Have all ready ordered my books. Wish I would have know about the coupon. I thought the 30% discount was included in the listed price. Ray, N6VR On Thu, Dec 31, 2015 at 1:30 PM, Scott Manthe wrote: > Hi Fred, > Do you happen to know the coupon code? > > 73, > Scott N9AA

Re: [Elecraft] KIO3B Audio Spec

On Thu,12/31/2015 11:29 AM, Barry N1EU wrote: You'll get hum if your computer and K3 chassis aren't at the same ground potential. Delete the word "ground." That has NOTHING to do with it. For many, it may be preferable to use the rear panel Line Out, which is transformer isolated. H!

[Elecraft] [TenTec_Eagle] Eagle and SKN

Remember tonight is SKN. Get out those old J-38's and those expensive Begali's and join us. Nothing like pounding a bit of old fashion brass. Happy New Year. 73 Bob, K4TAX __ Elecraft mailing list Home:

Re: [Elecraft] Elecraft website

Folks - Let's end the web site access reports at this time. This topic certainly been beaten to death and elecraft.com is clearly working from this end. 73 and have a great new year! Eric /elecraft.com/ On 12/31/2015 5:00 PM, Sid Frissell wrote: I just brought up the website on my iPad using

[Elecraft] WTB

I am looking for a K3/0 Mini if somebody has one excess to their needs. Pse respond off list. Tnx de Bill, WA8CDU Happy New Year __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: [Elecraft] Elecraft Website

Patience. Seriously. We need to think about two questions: Who owns the internet? How is it managed? The answers: nobody owns the internet. It's a network of networks ("Internet" is a contraction of inter-network, the protocol to tie multiple networks together). The various network

Re: [Elecraft] Elecraft Website

This useful utility can help in this kind of situation: http://downforeveryoneorjustme.com/ On Thursday, December 31, 2015, Doug Person via Elecraft < elecraft@mailman.qth.net> wrote: > No problems from rural Colorado using satellite. FYI, there are a lot of > players involved in transporting

Re: [Elecraft] Elecraft gear relative IMD

The FCC here in the USA does not require having a rig that meets state of the art specs, either for Amateur or many commercial applications. When checking shipboard radio installations in preparation for their annual FCC inspections, I used a variety of different specs the gear had to meet based

Re: [Elecraft] Elecraft gear relative IMD

Sure the rules apply, and rules for spectrum bandwidth provide no numbers, saying only "... in accordance with good amateur practice." Right now, New Year's eve, there is an on air event taking place, Straight Key Night, that encourages the use of antique rigs on the air and is sponsored by the

Re: [Elecraft] Elecraft website

still down in central Pa,,, looks like Verizon had a major outage last night still problems for elecraft,, other sites work ?? odd Bob K3DJC On Thu, 31 Dec 2015 18:00:02 -0700 Sid Frissell writes: > I just brought up the website on my iPad using first Hughesnet >

Re: [Elecraft] KIO3B Audio Spec

I've always believed in the star approach and completely agree with the series circuit issue. 73, Doug -- K0DXV On 12/31/2015 5:44 PM, Bob McGraw - K4TAX wrote: Don et al: Well Jim and I are at 100% opposite positions on this point. Bonding from equipment to equipment is a series circuit in

Re: [Elecraft] SKN.

It's on New Year's eve. Matt W6NIA Always store beer in a dark place. - R. Heinlein > On Dec 31, 2015, at 7:20 PM, Nr4c wrote: > > I've seen several references to Straight Key Nite being tonight. Guys, I > thought SKN was Jan 1st. On the east coast, it's still Dec 31st.

Re: [Elecraft] WTB

Not a K3X, but a remote control head. See: http://www.elecraft.com/K3-Remote/k3_remote.htm 73, Ron AC7AC -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Robert Harmon Sent: Thursday, December 31, 2015 7:00 PM To: elecraft@mailman.qth.net Subject:

[Elecraft] SKN.

I've seen several references to Straight Key Nite being tonight. Guys, I thought SKN was Jan 1st. On the east coast, it's still Dec 31st. SKN should be tomorrow nite. Right? Sent from my iPhone ...nr4c. bill __ Elecraft mailing list

Re: [Elecraft] WTB

thanks for the explanation everyone. I didnt know there was a K3/0 mini Happy New Year Elecrafters !! Bob K6UJ On 12/31/15 6:59 PM, Robert Harmon wrote: whats a K3/0 mini ? Maybe you mean K3X ? Bob K6UJ On 12/31/15 6:17 PM, wa8...@charter.net wrote: I am looking for a K3/0 Mini

Re: [Elecraft] SKN.

SKN is UTC on Jan 1st to 2359 on Jan 1st. New Year's Day UTC. 73, BILL W4RK Sent from my iPhone > On Dec 31, 2015, at 21:20, Nr4c wrote: > > I've seen several references to Straight Key Nite being tonight. Guys, I > thought SKN was Jan 1st. On the east coast, it's

Re: [Elecraft] Elecraft gear relative IMD

I honestly don't understand why this keeps coming up, or what it has to do with Elecraft. I'll operate my DX-40, or Viking II, or 100V or other vintage rig anytime and anywhere I please, thank you. These radios don't generally chirp wildly or have substantial phase noise. If phase noise is a

Re: [Elecraft] WTB

whats a K3/0 mini ? Maybe you mean K3X ? Bob K6UJ On 12/31/15 6:17 PM, wa8...@charter.net wrote: I am looking for a K3/0 Mini if somebody has one excess to their needs. Pse respond off list. Tnx de Bill, WA8CDU Happy New Year