Fldigi for the PC operates correctly with the K3 and AFSK_A as long
as radio control (CAT) is connected. The software/CAT interface
driver properly understands the sideband sense of the connected rig.
73,
... Joe, W4TV
On 2019-04-02 4:47 PM, Gmail wrote:
It appears FLDIGI MAC uses USB
Could it be this? I saved this item from a KE7X post. Worked for a
friend with a similar mystery problem -
VE7XF
...
At one point Elecraft had to change the switch that cuts out speaker
audio when the phones are plugged in so there is a setting in
Hi Joel,
It sounds like you have phones plugged in somewhere. The traditional way
of wiring rigs is that plugging in phones mutes the speaker (usually
they're powered from the same output stage). The K3 has separate output
stages for spkr and cans, and the switching is done by logic. Most of
Hey gang.
Just double checking my setup. I'm using a PK-232sc+ for sound card modes,
FSK RTTY, CW, and PACTOR with my K3s. I recently added the K144XV and since
everything is already hooked up, I tried sending packet. After tweaking the
AFSK control on the PK for proper deviation and proper
I'm a new K3s owner as of October, but I'll take a stab! I leave phones
plugged in to the back of the rig all of the time and an external speaker
all of the time. My settings are SPKRS = 2 and SPKR+PH =yes.
Hope that helps!
Hank
K4HYJ
-Original Message-
From:
I was able to turn off logging software mode send so I can use Data A or I
could use AFSK with rev. Also it’s possible to change K3 to USB AFSK. it’s not
a K3 problem but I thought others might have the issue. Took me a few hours to
sort out It all out.
I might have more info tomorrow. I need
Joel,
I don’t own a K3 so I am not familiar with all of the audio output settings
but is it possible you have a set of headphones plugged in that is
disconnecting the speaker? If not, maybe a dirty headphone jack?
Ken
WA2LBI
On Tue, Apr 2, 2019 at 20:44 Joel Hallas wrote:
> Tonight, when I
Tonight, when I turned on my early (sn 431), but upgraded to current, K3, I
was surprised to find I had no speaker audio with either internal or
external speaker(s). My first thought was that I had somehow fried the
speaker AF amp chip. But then I found that the speaker audio worked fine if
the
According to information available when we added RTTY to the K3, the standard
was LSB. So AFSK-A and FSK-D both use LSB. DATA-A and PSK-D both use USB.
This is not left to your imagination during operation, because "LSB" or "USB"
is shown along with "DATA" in the mode icon area. (This applies
Does using Reverse on the K3 make it easier to use the logging software spots?
73 Bill AE6JV
On 4/2/19 at 4:11 PM, anyone1...@gmail.com (Gmail) wrote:
> I recommend reading the FLDIGI manual. It states that USB is used for
> digital modes, including RTTY. The K3 uses USB for Data A and LSB
I recommend reading the FLDIGI manual. It states that USB is used for digital
modes, including RTTY. The K3 uses USB for Data A and LSB for Data AFSK.
In my first contest I was having problems getting reliable decoding and not
many responses to my calls. I asked a friend who is an PVRC RTTY
FLDIGI working under Windows 10 has no issues using the correct mode for AFSK
or PSK.
In FLDIGI you should be able to select PKTUSB for PSK mode and PKTLSB for AFSK.
Bob, K4TAX
Sent from my iPhone
> On Apr 2, 2019, at 3:47 PM, Gmail wrote:
>
> It appears FLDIGI MAC uses USB for RTTY
Thanks Eric (and beta testers)!
Dave wo2x
Sent from my waxed string and tin cans.
> On Apr 2, 2019, at 4:44 PM, Eric Swartz - WA6HHQ, Elecraft
> wrote:
>
> Guys - thanks for the help alpha testing 2.17!
>
> We should have this up on the website as Beta shortly.
>
> 73,
> Eric
>
It appears FLDIGI MAC uses USB for RTTY not the standard LSB. Use data A for
RTTY. If AFSK is used FlDIGI needs to be in REV mode.
If FLDIGI is not decoding correctly or no one answers calls, check the mode.
I don’t know if this applies to PC FLDIGI.
RAY
W8LYJ
Sent from my iPad
Guys - thanks for the help alpha testing 2.17!
We should have this up on the website as Beta shortly.
73,
Eric
/elecraft.com/
On 4/2/2019 9:24 AM, Roy Koeppe wrote:
Ditto, Ron!
73, Roy K6XK
Thanks, Ron!
73 de Dick, K6KR
Just installed new Firm-Ware Version 2.17. It has solved all
I need to make room in the shack….
K3/100 100 watt 160-6 meter transceiver SN7120, purchased January 2013 for
$2249.95, factory-built with following options:
-KAT-3 Antenna Tuner $339.95
-KPFLA3A -550 500hZ 5 pole filter $89.95
-KBF3 General Coverage BPF $159.95
In
Good Afternoon Gang,
I am selling my AlexLoop with a small camera tripod.
will ship today or tomorrow, or after 4/15/19 (out of town on vacation)
Asking $325 conus, + actual freight for other shipping requests.
Niel
WA7SSA
__
Elecraft
Beta testers only, be patient; that note was to the wrong list.
(no, I'm not one, just waiting like you).
Rick nhc
On 4/2/2019 12:11 PM, Jim McCook wrote:
I just spent 20 minutes trying to find 2.17 on the Elecraft KPA1500
Firmware download area. Only 2.10 and earlier betas are shown as
I just spent 20 minutes trying to find 2.17 on the Elecraft KPA1500
Firmware download area. Only 2.10 and earlier betas are shown as
available. I get nowhere with the Utility. Where is 2.17 hidden? -Jim
__
Elecraft mailing list
Sorry for inadvertent email…went to the wrong addressee.
73, Joe W2KJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Dan,
That looks like it should work fine.
73,
Don W3FPR
On 4/2/2019 11:50 AM, Dan Smith wrote:
Thank you, Don.
I think I have the Elecraft cable for the Keyline output/ACC2 as it
came with the cable pack that I purchased.
>From this lead, I would connect the RCA to the RCA amp port on
Ditto, Ron!
73, RoyK6XK
Thanks, Ron!
73 de Dick, K6KR
Just installed new Firm-Ware Version 2.17.
It has solved all the digital wattmeter anomalies and is working perfectly
here.
I recommend this version for next standard Firm-Ware update.
Thank you. 73's
Ron Durie
WB4OOA
Thanks, Ron!
73 de Dick, K6KR
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Ron Durie
Sent: Tuesday, April 2, 2019 08:59
To: Elecraft@mailman.qth.net
Subject: [Elecraft] KPA1500 v. 2.17
Just installed new Firm-Ware Version 2.17.
It has solved all the digital
Just installed new Firm-Ware Version 2.17.
It has solved all the digital wattmeter anomalies and is working perfectly
here.
I recommend this version for next standard Firm-Ware update.
Thank you. 73's
Ron Durie
WB4OOA
Elecraft K-Line
704-843-3681
My two narrowest filters have CONFIG -> FLx GN set to 6dB as opposed to
0dB for the others. Press the number keypad to select the appropriate
filter.
Martin, HS0ZED
On 02/04/2019 20:29, Ray Spreadbury via Elecraft wrote:
I have recently fitted a Sub Receiver & some additional filters to my
Ray,
I doubt that there is anything else wrong. Each filter will vary in its
gain (actually loss) amount. The 4 dB stated in the menu listing for
the 400 and 250 Hz filters is only a starting point.
73,
Don W3FPR
On 4/2/2019 10:36 AM, Ray Spreadbury via Elecraft wrote:
I had done that
Dan,
The KX3 has a KEYINE OUT output which will key your amplifier. It is on
the ring contact of the ACC 2.5mm jack. See page 5 of the KX3 manual.
When you add the KXPA100, there is a "black box" on the KX3 to KXPA100
cable set which brings that KEYLINE signal out to an RCA jack. See the
I had done that Don as per the Manual - 1-2dB for 400Hz & 3-4 dB for the
250Hz filter.
To get the right level of loudness I have had to add the max ie.8 dB. So, is
something else wrong?
Ray G3XLG
__
Elecraft mailing list
Home:
I am looking to see if anyone else has used an Ameritron AL811 with their
KX3 with positive results.
I plan on buying the KXPA100, but after buying the Shack in a Bag, I will
need to put it off for a little bit. In the mean time, I would like to try
using what I have, but I am hesitant to try
Ray,
You can set the gain parameter (FLxGN) parameter in the menu to
compensate for that. Either use K3 Utility or set it manually in the
CONFIG menu.
73,
Don W3FPR
On 4/2/2019 9:29 AM, Ray Spreadbury via Elecraft wrote:
I have recently fitted a Sub Receiver & some additional filters to
I have recently fitted a Sub Receiver & some additional filters to my new to
me K3S. I now have in the main RX, a 6K for AM, a 2.8K, 2.1K, 0.4K & 0.25K.
In the sub RX there is a 2.8K, 2.1K, 0.7K, 0.4K & 0.25K. I have a problem
with the 0.4K filter position in both receivers. Between about 0.45 &
31 matches
Mail list logo
