I have over the years had Elecraft Support loose my emails from time to time.
Also I have waited days for a response. Sometimes having to email a second
time. The problem with the email support system is the customer does not know
if the email has been received or read.
I have suggested on
Greetings list:
I'm writing some macros for the K3. One that I need is to save the current
VFO A and VFO B to channel 99. I'm using the following:
SWT15;MC099;SWT15;
It works, but when using the command tester of the k3 utility I receive a
?; after the command is sent, which the programmer
Hi Wayne.
I am expecting to buy a new radio next year so good discussion on the K4.
I expect to use my current upgraded K3 both at home and in the field,
perhaps at a field day event so high dynamic range is good. At home we
are out in a rural area so the K4 or K4D will be good.
I tend to
OK, I removed D16 and D17, and on the diode setting of my DVM, they both
measured the same value both forward and backward - 034. Which means they were
totally shorted.
I replaced them with new diodes (which measured 316 forward, and infinite
backward), and the RF display is once again
Rod,
I doubt that the Elecraft Principals and Engineers are such delicate snowflakes
that they are unable to deal with some frank feedback from any corner. And, in
many ways, critical feedback inviting a review of basic design principles is at
least as valuable as pages of Q about
I’ll be interested in hearing what you think after you use a K4.
Chuck Jack
KE9UW
Sent from my iPhone, cjack
> On May 24, 2019, at 7:00 PM, "hwhi...@maine.rr.com"
> wrote:
>
> Wayne and interested others,
>
> Way back when, I bought a loaded K3. I believe the S/N was around 4K? It was
>
Good answer. Reading that, I realize I don’t use B much.
Chuck Jack
KE9UW
Sent from my iPhone, cjack
> On May 24, 2019, at 7:43 PM, Wayne Burdick wrote:
>
> Hi Rick,
>
> Good question. Based in part on a survey of potential users, we chose to put
> the RIT/XIT knob at bottom right -- also
Not that I know of. But the knobs have only a minor draft, so custom bands
should work fine. I'd avoid anything very thick as that could impact usability
of nearby controls.
Same applies to the K4's VFO B and OFS knobs, which are the about the same size
as the K3's VFO B knob.
73,
Wayne
N6KR
I have done some searching to no avail. Is there a rubber cover for
the VFO B knob on K3/s radios?
Rich
K3RWN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Hi Rick,
Good question. Based in part on a survey of potential users, we chose to put
the RIT/XIT knob at bottom right -- also a traditional location, one that
matches that of the K3/K3S/KX2/KX3. VFO B is less often used in practice. That
said, the radio is only 4.5" tall and both knobs are
First, let me say, I have never owned an Elecraft radio or amplifier but I have
become interested in the K4 and the KPA1500 amplifier combination.
One of the most surprising features on the K4 is VFO B is located at the top
right side of the radio. Thus you cannot rest the palm of your hand
> On May 24, 2019, at 5:00 PM, hwhi...@maine.rr.com wrote:
> Last week the K4 was announced so I rejoined the reflector. ... From all that
> I have read, the controls will be even more complex.
The K4's controls are actually quite a bit simpler, and more intuitive, thanks
to the new
Harry, you got they the first time.
I respect your right to an opinion and right to vote with your dollars. You
represent a market segment that Elecraft May or may not choose to address. It’s
Wayne and Eric’s strategy to decide.
I for one may represent a different (slightly) younger market
Second try.
-Original Message-
From: hwhi...@maine.rr.com
Sent: Friday, May 24, 2019 8:00 PM
To: 'Wayne Burdick' ; 'Elecraft Reflector'
; 'k...@yahoogroups.com' ;
'elecraft...@groups.io'
Subject: RE: [Elecraft] Elecraft K4 and Accessibility
Wayne and interested others,
Way back
Wayne and interested others,
Way back when, I bought a loaded K3. I believe the S/N was around 4K? It was
back in the day when almost every DXpedition was using K3's so it was obviously
the radio to own. (Around 2009?) It was at the top of the Sherwood ratings.
Owner's bragged, incessantly,
yes
Eric
/elecraft.com/
On 5/24/2019 4:42 PM, Tom Warren wrote:
When the K4 is interfaced to a PC or TV monitor will it be possible to
completely
control the K4 via mouse, not only VFO’s but the button menus?
Tom
"Don’t confuse effort with results.”
When the K4 is interfaced to a PC or TV monitor will it be possible to
completely
control the K4 via mouse, not only VFO’s but the button menus?
Tom
"Don’t confuse effort with results.”
__
Elecraft mailing list
Home:
Apologies if I missed that one. Please re-send.
tnx
Wayne
N6KR
> On May 24, 2019, at 12:46 PM, Hisashi T Fujinaka wrote:
>
> Oh, one thing I forgot, I did send an email to Eric and Wayne about my
> odd interactions and I got no reply.
>
> On Fri, 24 May 2019, Hisashi T Fujinaka wrote:
>
>>
Thanks Wayne, something to look forward to
--David
-Original Message-
From: Wayne Burdick
Sent: Friday, May 24, 2019 3:39 PM
To: bear...@yahoo.com
Cc: Buddy Brannan ; Elecraft Reflector
; k...@yahoogroups.com; blind-h...@groups.io
Subject: Re: Elecraft K4 and Accessibility
Short
Short answer: yes, but I can't put a date on it yet.
Wayne
N6KR
> On May 24, 2019, at 1:09 PM, David wrote:
>
>
> Is it possible to get the audio CW feedback on the K4, or even the K3/K3S?
>
> --David
>
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net On
> Behalf
What is the Linux processor and stats in the K4?
Just curious like a nerd
Lee K0WA Nerd since 1950
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I am selling my K3S with extras
It includes:
KPA3A 100 watt amp
KAT3A ATU
KXV3A IF in/out
2nd Receiver
KIO3B USB audio in/out
Both Main RX and Sub RX have same filters in each
2 each KFL3A-2.7K (2.7khz, matched pair)
2 each KFL3A-400-IR (inrad filters, 400 hz, 8 pole)
2 each KFL3A-200 (200 hz,
What do people think about voice recognition? Recent Google Android phones
do a decent job of voice recognition on the phone itself with no connection
to the internet or cloud voice recogniton servers. There are open source
voice recognition software applications that run on Linux. No idea how
You forgot to mention that "miracle of control" called the K-Pod.
Without it, I would be chasing the K3 with a mouse via HRD (mouse or
K-Pod sits on the edge of my desk within easy reach). I prefer to run
without being tethered to a computer.
A few extra buttons on the K-Pod would be great,
Is it possible to get the audio CW feedback on the K4, or even the K3/K3S?
--David
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Buddy Brannan
Sent: Friday, May 24, 2019 11:26 AM
To: Wayne Burdick
Cc: Elecraft Reflector ; k...@yahoogroups.com;
Since on at least one occasion your unanswered email was discovered in
Elecraft’s spam folder, it’s possible your email domain is being flagged for
some reason by whatever mail host/service/application is being used at Elecraft.
Grant NQ5T
K3 #2091 KX3 #8342
> On May 24, 2019, at 3:46 PM,
So the problem is clearly in the transvertor.Given the fact that both rx and tx
follow roughly the same pattern a common cause seems to be logical.That could
be voltage or oscillator.Check if the voltage remains constant on both rx and
tx circuits. Also check the oscillator signal and level
Oh, one thing I forgot, I did send an email to Eric and Wayne about my
odd interactions and I got no reply.
On Fri, 24 May 2019, Hisashi T Fujinaka wrote:
I'm on the they're very good, but not everything goes right list.
My KPA1500 died (I think they had a bad run on capacitors because others
You are right Terry! And I need to get back to some that when I return, for
a little life balance.
73,
Dave, W8FGU
On May 24, 2019 09:46:28 "Terry Schieler" wrote:
In addition to Dave's many talents, he is also a fine drummer. "Steady
feet" are a requirement and a result of years of hard
I'm on the they're very good, but not everything goes right list.
My KPA1500 died (I think they had a bad run on capacitors because others
have reported the same thing to me via email) and I emailed the list
here on a Sunday. Eric immediately asked for logs to be sent to support.
Now I've had
Hi Wayne,
Thanks as always for your direct response. I appreciate your forthrightness on
this issue and willingness to tackle the more difficult
questions/aspects/design decision justifications.
Elecraft has, as I stated in my original email, always been supportive of the
blind ham community
Have you double checked all of the connections in and out of the 2M module?
I’ve found it’s important to remove the transverter’s top cover to do this —
because it is possible when pushing cables into the female connectors blind,
even being careful, to actually bend back the business end of
Hi Buddy et al,
We've definitely been thinking about this.
There's a paradigm shift going on in transceiver design, and we reached a point
where we needed to embrace it. This shift is not entirely aligned with
accessibility, as you know. I'll address alternatives in this email.
As for the K4
OK...here are some test results:
- Neither problem occurs on 10m FM
- The output power does also diminish on 2 meters - roughly follows the
reception "weakening". The S-Meter went from 60 over S9 to S8 over the period
of 45 minutes and the output power (measured by a Bird WM) fell from 12
'Sound card' clocks are usually independent of others in the system.
73,
Eric
/elecraft.com/
On 5/23/2019 8:20 PM, Tom Azlin W7SUA wrote:
Hi Eric,
Is the sampling clock for the internal sound card driven by the reference
oscillator? Or does it have an independent crystal oscillator for
In addition to Dave's many talents, he is also a fine drummer. "Steady
feet" are a requirement and a result of years of hard work.
Terry, WØFM
-Original Message-
From: Bill Johnson [mailto:k9...@live.com]
Sent: Thursday, May 23, 2019 7:02 PM
To: Dave Van Wallaghen;
Plenty of room and you will luv the K-pod!
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
Folks - this thread is getting a bit long - let's close it at this time in the
interest of keeping list volume reasonable for our other readers.
Also, once a thread had hit 5-10 posts, please do not continue to argue pro-con
positions on the list. At that point it is best taken to private email
I totally disagree. With the tools that are available to us these days,
one person could produce change pages for the K3 fairly quickly.
However, I think I have a homebrew solution - annotate the manual with
the changes reflected in the Release Notes, and keep them in a separate
binder, in
Plenty of room with out raising the rig.
Chuck Hawley
c-haw...@illinois.edu
Amateur Radio, KE9UW
aka Jack, BMW Motorcycles
From: elecraft-boun...@mailman.qth.net on
behalf of Tony - KM0O
Sent: Friday, May 24, 2019 8:18 AM
To: elecraft@mailman.qth.net
It will fit. My K3s sits flat with the K-Pod connected.
--ae0mm
‐‐‐ Original Message ‐‐‐
On Friday, May 24, 2019 8:18 AM, Tony - KM0O wrote:
> I'm thinking about purchasing a K-pod. My K3 sits flat on a shelf, on its
> four rubber feet without the bail extended. Will I have enough
I'm thinking about purchasing a K-pod. My K3 sits flat on a shelf, on its
four rubber feet without the bail extended. Will I have enough clearance
underneath the K3 to attach the K-pod cable, or does the front end of the K3
need to be raised?
Thanks and 73,
Tony KM0O
--
Sent from:
When I got my K3 at the end of 2008, I soon discovered that the firmware was
updated fairly often & I needed to keep track of the changes.
The hfwnotes.rft has every update from the first to the latest firmware
updates.
My career as as broadcast engineer I had developed a habit keeping all
Hi guys,For sale one assembled and fully functional KDSP2 with the mounting
hardware.Asking 150 USD plus shipping from my prezent QTH, Bucharest, Romania,
KN34BK (about 20 USD last time I checked).73' de YO3IAZ, Cristian
__
Elecraft
44 matches
Mail list logo