I dare any of the other major competitors to match Elecraft's response
time
73
Jay
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick
Sent: Tuesday, May 18, 2010 4:09 PM
To: elecraft...@yahoogroups.com
Cc:
Perhaps I stated the question incorrectly.
Is there a list of the factory default parameters
in the configuration, so that one can compare the default
to the present setting.
Jay
__
Elecraft mailing list
Home:
Thought there would be one of those in with the radio I got back yesterday
Wayne..:(
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick
Sent: Tuesday, September 29, 2009 8:34 PM
To: Larry - K2GN
Cc: Elecraft - K3
Anyone have any luck running N1MM directly on a laptop with
no serial connector and a USB to serial convertor?
Primarily for cw?
Thanks
Jay
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I have a problem with noise in the shack.
On transmit it is picked up by the mic. Other than lowering the RF gain I
understand that
there is a setting which could reduce or eliminate this
some where in the config. Any tgoughts would be appreciated.
Thanks
Jay
Jay Rodaman
Thanks for all the answer
I have tried the level at about 10
seems to do the trick.
73
jay
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I am able to access the bank 1 memories through N1MM and
figured how to access the Bank 2 memories also with N1MM.
however when I access the Bank 2 memories (N1MM F5-F8)
the F1 key then uses the Bank 2 K3 memories. That might not be clear
but what I want to end up with is N1MM F keys 1-8
Programming N1MM to use the K3 memories 1-4 is a great aid, but is there a
way to address memories in the 2nd bank M5-M8 in the same fashion?
Thanks
Jay
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Iain MacDonnell -
N6ML
I have also had a similar need for external speakers.
The recommendation from an unnamed source (heh heh) on the left coast
was the following
http://www.bestbuy.com/site/olspage.jsp?skuId=7314523type=productid=111884
3685964
they are not very expensive , to the delete of most of us
and seem
I guess to many times hitting the delete key...should have been delight
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jay Rodaman
Sent: Saturday, April 04, 2009 2:46 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft
I have turned on the sub-rx for diversity mode during the 160 test and find
the following.
1. The diversity works fine
2. When I click on the Q's and mults window the sub disengages
How can I keep the diversity mode engaged when clicking on spots?
Thanks
Jay
Thanks that did the trick..
Allu gots to du is aks ..lol
Jay
-Original Message-
From: Guy Olinger, K2AV [mailto:olin...@bellsouth.net]
Sent: Saturday, February 28, 2009 9:13 PM
To: Jay Rodaman; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 and N1MM (sub-rx)
This is an MM logger
I had the same problem, but during construction, probably over tightened the
little set screw, Should remember
It is a radio not a truck
Jay
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ron Hinton
Sent: Tuesday, February 03, 2009 7:45 PM
I second that!!
Jay(K2TTT)
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of DOUGLAS ZWIEBEL
Sent: Tuesday, January 27, 2009 7:38 AM
To: Elecraft Reflector
Subject: [Elecraft] why Elecraft is simply the BEST there is
RE:
It would be great if all you had to do was route a bnc jumper from RX ant
OUT to the AUX ant on the sub-
Receiver and in that way when the sub was active it would use the receive
antenna for diversity
And when inactive it would be the main receiver REC antenna.
-Original Message-
From:
Just getting my K3 up and running. I have a K9AY loop and would like to
Have that as the receive antenna each time I change band to 160/80
Is there a way for the radio to remember this activity? Or do
I have to press the rcv antenna switch each time?
Comments appreciated.
BTW a million
Just setting up my new K3 with sub receiver.
I have the Original Microkeyer and got the matching cable set for the K3
Question is:
There are two connectors that I do not know where to connect
1.RCA female marked INHIBIT
2. Female mini-plug marked SUB RX
Where do these go?
Thanks for any help
Jay
Just finished my K3 works great
Interfaced with the microkeyer
which reads the frequency and keys cw fine.
Now I need to configure N1MM to put it all together.
Created ports as follows in Router
2=Radio
3=Ptt
6=foot switch
8=winkey.
Can someone help me get N1MM configurer to
put all this
18 matches
Mail list logo