e original poster's question, yes, the amp will reduce output
as it gets warmer. In my case it drops about 100 watts (1500 -> 1400) which is
-0.3 dB. Hardly enough to worry about.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Kevin Robertson via E
SO2R setup and interleave QSOs.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Frank Scolaro
Sent: Friday, April 1, 2022 8:46 AM
To: James Bennett ; Elecraft Reflector Reflector
Subject: Re: [Elecraft] KPA500 Issue
Jim,.
I use the "1A2R" (one
"and sold his company to Raytheon..."
Didn't he sell to Rockwell? Then I think some of Rockwell went to Boeing, but
I'm not sure which part was the radio part.
Can't say I've ever seen a Boeing Collins radio though :^)
Ken K6MR
From: ele
n the frequency I want without removing
my hands from the keyboard.
I think with the amplifier they just had so much front panel space available
that they just couldn't think of anything else to put there. In the years I've
had KPA500s and a KPA1500 I have yet to touch the
As shown on page 5 of the KAT500 schematic: 12V levels, Tip = Rx, Ring = Tx.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Gordon LaPoint
Sent: Tuesday, March 22, 2022 10:29 AM
To: Elecraft Reflector
Subject: [Elecraft] KAT500 serial pinout
And let me add that the sound track was also produced by 100% Elecraft. Thanks
to Dean for making me look (er, sound) good.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Dean Wood
Sent: Friday, February 11, 2022 8:38 AM
To: elecraft
I don't remember the slider ever moving in response to the fan speed while in
Auto mode. The current fan level is noted in the lower info bar by a number (1
- 5), but that's it.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Ed G
Sent: Sunday
"If it is an FPGA, you will need to get Elecraft to program it."
No. The FPGA gets loaded each time you turn on the P3. There are different
code images for each monitor resolution. So the uP checks which resolution you
have selected and loads the proper code for that resolution.
The FPGA is a Xilinx XC6SLX9 in a FTG256 1.0 mm pitch BGA package.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Mark Goldberg
Sent: Thursday, January 20, 2022 4:18 PM
To: j...@audiosystemsgroup.com
Cc: Reflector Elecraft
Subject: Re
Not sure if this has been suggested: did you check the fuses on the power
supply board? Those will kill the LV supplies and will keep things from
powering up.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Sam Sargent via Elecraft
Sent: Monday
a ground
bounce. That is sure to take out lots of stuff.
Ken K6MR
From: Dr. William J. Schmidt<mailto:b...@wjschmidt.com>
Sent: Sunday, November 28, 2021 06:38
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft] [POSSIBLE SPAM] Re: [POSSIBLE SPAM]
Cheap too, I think it was no more than $10 per board parts cost.
Ken K6MR
From: David Gilbert<mailto:ab7e...@gmail.com>
Sent: Saturday, November 27, 2021 09:17
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft] [POSSIBLE SPAM] Re: Need K3 Board
I t
Thanks to everyone for the comments. Sounds like the KX3 works fine in this
environment. I should have known since it is an Elecraft radio :^)
Ken K6MR
From: Steve Hall<mailto:99sun...@gmail.com>
Sent: Monday, November 1, 2021 15:00
To: elecraft@mailman.qth.net<mailto
, which would be easy even
with the 100 watt amp.
Thanks for your thoughts and experiences.
Ken K6MR
From: kevin<mailto:kev...@coho.net>
Sent: Sunday, October 31, 2021 22:43
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] Elecraft CW Net Errata she
this is Q5 on the main RF board. The active device parameters are
different but not enough to worry about in the circuit where Q5 is used. It is
nothing but a switch to reverse the active state of the 7R line to activate the
big FET used for the Key Out line. The 2N7000 will be fine.
Ken K6MR
I’d start with the Public Utilities Commission. I had good response from them
when dealing with PG I ‘think’ cable companies are under their
jurisdiction, but if not they can probably tell you who does deal with them.
Ken K6MR
From: eric norris via Elecraft<mailto:elecraft@mailman.qth.
KPA1500 owner’s manual, page 31. Under “menu items”, “fan speed min”. There
are 5 levels from which to choose.
I’ll refrain from asking you why.
Ken K6MR
From: Ronnie Hull<mailto:w5...@comcast.net>
Sent: Sunday, August 8, 2021 10:08
To: elecraft@mailman.qth.net<mailto
My radios only do the power ramp up the first time you transmit after changing
bands. Doesn’t take that long though. Less than one second I would guess. As
noted, it’s the power control loop. Usually it’s not that noticeable.
Ken K6MR
From: John Reilly<mailto:reill...@gmail.com>
Config -> LIN OUT -> tap REV/2 button. Use VFO A knob to adjust t= xxx to set
transmit monitor level. 0 = none and up from there. Mine are set at 010.
YMMV.
Ken K6MR
From: HP<mailto:pfizenma...@q.com>
Sent: Wednesday, April 28, 2021 23:36
To: elecraft@mailman.qth.net<
seem
to be a big problem up here. One lineman told me they changed vendors to a new
style and he’s seen quite a few go bad.
My noise guy is still around, office in Cottonwood, just south of here.
Friendly enough, and does help the process move forward.
Ken K6MR
From: Josh Fiden<mailt
noise and they go to work.
Ken K6MR
From: MIKE ZANE<mailto:n...@comcast.net>
Sent: Tuesday, April 27, 2021 10:33
To: j...@kk9a.com<mailto:j...@kk9a.com>;
elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft] [OT] Ham Radio near high voltage power li
in hot exhaust from the top vents back into the amp. Of course this
won’t be a problem if you have the amp on a desk with nothing above it. I have
the minimum recommended clearance of 2” above the amp, and 4” above the power
supply.
Ken K6MR
From: N4ZR<mailto:n...@comcast.net>
Sent: Sa
“just not publically posted.”
Which seems very strange since they post for all the radios, which are far more
complex. When I asked about a schematic, I was told “No”. Same with some
updates.
Just seems strange.
Ken K6MR
From: Dr. William J. Schmidt<mailto:b...@wjschmidt.com>
Sent:
they’ve ever done
that before.
Ken K6MR
From: Dave<mailto:rocke...@gmail.com>
Sent: Sunday, February 21, 2021 11:06
To: Dana Roode K6NR<mailto:dana.ro...@gmail.com>
Cc: Elecraft Reflector<mailto:Elecraft@mailman.qth.net>
Subject: Re: [Elecraft] Sudden KpA1500 power reduction
I
deck is going to take some
time. I’d rather not if I don’t have to.
Ken K6MR
From: Dana Roode K6NR<mailto:dana.ro...@gmail.com>
Sent: Sunday, February 21, 2021 11:03
To: Frank Scolaro<mailto:fscol...@mindspring.com>
Cc: Elecraft Reflector<mailto:Elecraft@mailman.qth.net>
Subj
Don’t think so. The only way I know to use a big knob for RIT is a KPOD.
Ken K6MR
From: James AC0E<mailto:h...@ac0e.com>
Sent: Monday, February 15, 2021 15:26
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] Remap VFO "B"
Ju
is too short, 300
ms works, but may be overkill. If the value is 200 ms or less the radio drops
a few dits at 36 wpm when you first transmit after a split mode change.
What would be a good typical value that would always work?
Tnx,
Ken K6MR
Do not use a Y cable. I could go into the whole technical description, but
don’t.
I’m assuming here a normal non-USB K3. What you should do is connect the P3
normally to the K3 through the XCVR port on the P3, and then connect the
Microham device to the PC port on the P3.
Ken K6MR
From
It’s a common problem with documentation for just about everything these days.
Luckily with pdf files it’s pretty easy to add notes or edit things yourself.
And of course when all else fails there is always the group. Something about
the group being smarter than any individual!
Ken K6MR
You are reading an old description of the SUB button. A firmware change made
the long press of SUB the activation of Diversity. Linking is done through the
config menu.
Ken K6MR
From: John Lemay<mailto:j...@carltonhouse.eclipse.co.uk>
Sent: Saturday, December 26, 2020 09:13
To: El
Einstein had a whole bunch of great quotes:
“Only two things are infinite, the universe and human stupidity, and I'm not
sure about the former."
Ken K6MR
From: Phil Kane<mailto:k2...@kanafi.org>
Sent: Wednesday, December 23, 2020 19:57
To: elecraft@mailman.qth.net<m
Dunno. Works here.
Ken K6MR
From: Victor Rosenthal 4X6GP<mailto:k2vco@gmail.com>
Sent: Sunday, December 13, 2020 19:33
To: Ken K6MR<mailto:k...@outlook.com>; Elecraft
Reflector<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft] [K3] Locking VFO B
Still doesn't wor
Yep, looks like that’s either a bug or a feature. When in diversity mode and
BSET using LOCK gives the same response as RX ANT. Maybe what it’s trying to
say is that you can’t lock B because it is already “locked” to VFO A .
Ken K6MR
From: Victor Rosenthal 4X6GP<mailto:k2vco@gmail.
Long press A/B (BSET) and then long press RATE (Lock)
Ken K6MR
From: Victor Rosenthal 4X6GP<mailto:k2vco@gmail.com>
Sent: Saturday, December 12, 2020 20:24
To: Elecraft Reflector<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] [K3] Locking VFO B
I seem to recall that the
Yes.
Ken K6MR
From: eric norris via Elecraft<mailto:elecraft@mailman.qth.net>
Sent: Saturday, December 12, 2020 11:28
To: donw...@embarqmail.com<mailto:donw...@embarqmail.com>; Don
Wilhelm<mailto:donw...@embarqmail.com>; Elecraft
Reflector<mailto:elecraft@mailman.qth.n
Use the Kenwood diagram in the KPA manual. Use the pinout in the K2 manual
for the serial port and wire accordingly. 3 wires (TXD, RXD, GND) is all you
need from the K2. Then select SERIAL as the radio type in the KPA. You may
also need RADIO POLL to be turned on.
Ken K6MR
From: eric
Send a note to Elecraft support and ask for the manufacturer part number. I’ve
always received a reply and often with the Mouser or DigiKey part number
included.
Ken K6MR
From: hawley, charles j jr<mailto:c-haw...@illinois.edu>
Sent: Friday, November 6, 2020 07:55
To: Elecraf
You can buy Amphenol cables that are 15 wire with any combination of connectors
you want from places like Mouser and Digikey.
Ken K6MR
From: Eric Norris<mailto:norrislawfi...@gmail.com>
Sent: Tuesday, October 20, 2020 12:57
To: Howard Sherer<mailto:h...@lehigh.edu>
Cc: elecraft<
This is easy to do with an Arduino if you are capable with those kind of
things. The serial port on the Arduino can read the data from the K3, and
set/clear a relay at any frequency you want. Some assembly required. :^)
Ken K6MR
From: Dennis Ashworth<mailto:dennisashwort...@gmail.com>
switch on the
KPA or select operate. You should see the KPA500 Operate message. The other
way you can check is wiggle the PWR knob and make sure the * is in the window.
That tells you that the radio is using the amp power settings.
Ken K6MR
From: Tom Doligalski via Elecraft<mailto:elecr
Before the KPA1500 was released, I ran two KPA500s in parallel. On the high
bands, a K3 would not drive both amps to 500 watts. The NX1P mod enabled a
full 1000 W out on all bands.
Ken K6MR
From: Phil Hystad via Elecraft<mailto:elecraft@mailman.qth.net>
Sent: Thursday, June 18, 2020
You didn’t happen to notice the value of the changed resistor did you? The fan
resistor is the big one.
Ken K6MR
From: rocke...@gmail.com<mailto:rocke...@gmail.com>
Sent: Thursday, June 4, 2020 17:00
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft]
Not sure what you mean by “multi TX contest environment”, but I use mine in a
SO2R setup. Two K3s into the single KPA1500. Works just fine. It’s in the
closet and I hardly ever touch it. It just keeps making watts.
Ken K6MR
From: Salvatore Ted K2QMF<mailto:k2...@juno.com>
Sent: Sa
I think you are looking for the Tx line out monitor level. LIN OUT (from
Config menu) and press 2. 0 should give you no monitor output.
Ken K6MR
From: K9MA<mailto:k...@sdellington.us>
Sent: Sunday, November 17, 2019 14:29
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net
This just shows you how well this state is run. Fires, power outages,
homelessness, third world diseases in the big cities, and what do they decide
to do?
Luckily I’m in the State of Jefferson and we’re fine :^)
Ken K6MR
From: elecraft-boun
Yep, we’ve all received our text message, email, and phone call. They are
taking no chances.
My generator is fueled and ready :^)
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Ken G Kopp
Sent: Monday, October 7, 2019 2:33:29 PM
Cc
“We need a splitter/breakout device.”
N6TV’s Y Box.
From: elecraft-boun...@mailman.qth.net on
behalf of Randy (Art)
Sent: Monday, August 26, 2019 12:12:05 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] kpa 1500
Pete that would be in k3 test mode.
and the amps were remoted in a closet 20 feet from
the operating desk. No problems.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Bob McGraw K4TAX
Sent: Tuesday, August 20, 2019 12:59:11 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft
I pulled mine out a while back to understand the fan circuit and it’s pretty
obvious. Just make a diagram of the connectors so you don’t accidentally swap
one.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of eric norris via Elecraft
Sent
does make a bit of fan noise on RTTY when dual CQing, but otherwise
works just fine. I have the amp in a closet so the noise is not a concern.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of j...@kk9a.com
Sent: Friday, June 28, 2019 7:04:10 AM
Windows 10 allows you to delay updates for up to 35 days.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Jim Brown
Sent: Thursday, June 20, 2019 12:16:53 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] new computers, the search
True. However, the advantage of the K3/KAT500 (assuming you have the AuxBus
connected) is that the KAT500 will follow the K3 frequency without
transmitting. KPA1500 tuner does the same thing.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf
is way too short for anything other than a
standalone PC. Putting one into a high quality, specialized
instrument/radio/whatever makes no sense at all.
Ken K6MR (retired PE)
From: elecraft-boun...@mailman.qth.net on
behalf of Bryan Brauer
Sent: Monday, May 6
The B VFO doesn’t do anything in diversity receive. Both receivers are driven
by the A synth. B VFO is only used for a split transmit frequency if you want.
You are thinking of the VFO LINK mode where B follows A with a given split.
Ken K6MR
From
Use the command line options in a batch file. The options are COM Baud Port
timeout. Something like:
start KAT500-Remote.exe COM13 38400 4629 2000
start KPA500-Remote.exe COM11 38400 4627 2000
Insert your appropriate values.
Ken K6MR
From
What we call a “foot switch” is a “sustain pedal” in guitar speak (the real
market). The standard is a 1/4” plug. Buy an adapter.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Michael Gillen via Elecraft
Sent: Tuesday, April 16, 2019 6:05
I don’t operate there either!
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Tom Georgens
Sent: Monday, March 18, 2019 6:01:04 PM
To: j...@audiosystemsgroup.com; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Using Elecraft KPA-1500 for 2
Both amps and tuner have been sold. Thanks for everyone’s interest.
Thanks to the list (and Eric!) for the bandwidth.
Ken K6MR
From: Ken K6MR
Sent: Friday, March 1, 2019 4:58:42 PM
To: Elecraft Reflector Reflector
Subject: KPA500 / KAT500 For Sale
The new
great, no problems since I’ve had them. Excellent physical
condition.
Please contact off list for additional info, pictures, etc.
Ken K6MR
k6mroutlook.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo
is no problem.
The W6PQL splitter/combiner are the units he makes for his two pallet amplifier
kit. So they are being used well below the designed power level.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Bob McGraw K4TAX
Sent: Tuesday
. This allows a single K3 to drive both amps to
full output even on 10 meters.
Connect inputs to the splitter, outputs to the combiner using (obviously) equal
length coax to main phase relationship.
Some assembly required but not rocket science.
Ken K6MR
From
“Actually, I suppose one could drive 2 KPA500's
from one K3 and sum the output for a virtual KPA1000.”
Yes you can. I have been doing this for the last 3 years.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Fred Jensen
Sent: Tuesday
The RTL-SDR has a direct sampling mode that will do HF. $30 is about as cheap
as it gets. Not as good as a real P3 but it does work.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Bob McGraw K4TAX
Sent: Thursday, November 8, 2018 8:14:30
Configuration page of the utility, “Initial Power” tab. Uncheck “Power On when
DC power applied”.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Allen Bush via Elecraft
Sent: Wednesday, September 19, 2018 4:46:25 PM
To: elecraft
the desk and the
radios don’t make any noise.
Suum cuique!
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of Grant Youngman
Sent: Saturday, July 21, 2018 9:55:11 PM
To: kevinr
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Headphone jack
Best earbuds bar none: Etymotic. Not cheap. Nothing really good is.
Ken K6MR
From: elecraft-boun...@mailman.qth.net on
behalf of kevinr
Sent: Saturday, July 21, 2018 7:39:31 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] Headphone jack impedance
I
Proprietary. I’ve decoded a couple of messages, but AFAIK there is no
publication.
Ken K6MR
From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on
behalf of ANDY DURBIN <a.dur...@msn.com>
Sent: Sunday, April 29, 201
Page 15 of the owner’s manual has a table of the segment width vs. frequency.
So in answer to your question: “It depends”
Ken K6MR
From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on
behalf of Harlan Sherriff via Elecraft <
The beeps are not very loud, and fairly high pitched. I don’t bother shutting
them off because I never operate on a speaker and don’t notice them. But if
your high frequency hearing is pretty good you might notice the beeps in a
quiet room.
Ken K6MR
From: Kenneth Moorman<mailto:n...@cox.
Hold F1 during power up. It will revert to beeping at the next power up so
you need to do this each time it is power cycled.
Ken K6MR
From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on
behalf of Jim Miller <j...@jtm
Config -> VFO LNK and set to OFF. This is a by band setting so be sure you are
on 20 before changing.
Ken K6MR
From: Bob Gibson via Elecraft
Sent: Wednesday, February 28, 2018 11:42
To: Elecraft@mailman.qth.net
Subject: [Elecraft] VFO TRACKING
I have looked in both manuals to find out
you need their
high side driver board also.
Ken K6MR
From: Jack Brindle
Sent: Sunday, February 25, 2018 14:42
To: Reflector Elecraft
Subject: Re: [Elecraft] Advice needed: Remote Station Enhancement
Interesting idea, but I would talk to N6TV before going too far down this path.
The reason
(rather than absolute commands
like RT and XT) which requires knowing the current state of the function.
K3 fw 5.62, P3 FW 1.60
Ken K6MR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
You have super hi speed QRQ turned on. Go to Config->CW QRQ and set it
to off.
Ken K6MR
On 10-Feb-18 11:58:03, "Ken Widelitz" <kwidel...@gmail.com> wrote:
The "+" icon is on in the Mode portion of the LCD window in CW mode on
one
of my K3s. It is off in
The dummy load needs to be connected to the XVTR OUT jack, not the main
antenna connector. The tuner path has nothing to do with it.
See K3 manual around page 53 or so.
Ken K6MR
On 05-Feb-18 20:59:03, "John Woodard" <john.l.wood...@gmail.com> wrote:
On Sun, Feb 4, 20
/A for your radio.
Ken K6MR
On 01-Feb-18 20:36:25, "Andy Faber via Elecraft"
<elecraft@mailman.qth.net> wrote:
My K3 came back from being upgraded and seems to have a new menu item,
called ATTEN, with "10db" displayed. When I turn the big knob, it stays
at that value and
e
few use the VFO linking function. Those who do use VFO linking can still
turn it on by setting CONFIG:VFO LNK to ON. This menu entry can be
assigned to a programmable function switch for easy selection if
desired, eliminating the need to bring up the menu.
Ken K6MR
On 23-Jan-18 18:01:2
Just set the SWR thresholds so that it automatically goes into bypass
below whatever mismatch you consider good enough.
Ken K6MR
-- Original Message --
From: "j...@kk9a.com" <j...@kk9a.com>
To: elecraft@mailman.qth.net
Sent: 29-Nov-17 09:25:43
Subject: [Elecraft
.
Ken K6MR
From: E T <etks...@gmail.com>
Sent: Monday, November 6, 2017 5:28:16 PM
To: Ken K6MR
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 actual radiated power during tuning
I know the training process, have done it many times on all my
and switch values without any rf at all.
Ken K6MR
From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on
behalf of E T <etks...@gmail.com>
Sent: Monday, November 6, 2017 4:52:17 PM
To: Fred Jensen
Cc: elecraft@mailman.qth.net
Thanks for the responses (and to Eric and Wayne for the bandwidth).
Ken K6MR
From: Ken K6MR <k...@outlook.com>
Sent: Monday, October 30, 2017 5:16:38 PM
To: elecraft@mailman.qth.net
Subject: K3 filters available
I have some K3 filters I don’t nee
2.1K is sold. (Tnx Terry N7BDL)
Ken K6MR
From: Ken K6MR<mailto:k...@outlook.com>
Sent: Monday, October 30, 2017 17:17
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] K3 filters available
I have some K3 filters I don’t need:
(2) of the KFL3A-200
I have some K3 filters I don’t need:
(2) of the KFL3A-200 Fc = -0.98 and -0.94
(1) of the KFL3A-2.1K
$75 each shipped CONUS. Paypal preferred.
Ken K6MR
k6mr -at- outlook.com
__
Elecraft mailing list
Home: http://mailman.qth.net
Max-Gain Systems has 1.125” and 1.75” models if one of those would work.
Ken K6MR
From: Martin<mailto:dm...@t-online.de>
Sent: Thursday, September 14, 2017 09:12
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] OT: Looking for adaptor
Elecrafter
Green Heron Engineering is one possibility.
Ken K6MR
From: Gary Smith<mailto:g...@ka1j.com>
Sent: Tuesday, September 12, 2017 16:31
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] K3s & remote coax switching
Question: Is there a remote coax swi
Yes, but those electrons are really tired after all the work they did and need
to go home to rest and regenerate….
Ken K6MR
From: Fred Jensen<mailto:k6...@foothill.net>
Sent: Monday, September 4, 2017 11:05
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: R
Assuming it is in the vicinity of the K3, use the station power supply. If
it’s somewhere else, just about any wall wart will work. Spec is 200 mA typ.,
1.0A max.
Ken K6MR
From: Sid Frissell<mailto:sidfriss...@gmail.com>
Sent: Wednesday, August 23, 2017 20:46
To: Elecraft@mailman.q
Southern/Central
California to the eclipse area.
http://www.dot.ca.gov/dist2/travelmap.htmShould make for interesting
viewing this weekend. Click on the red dots to view the camera at the site.
I for one plan to stay well clear of I-5 this weekend…
Ken K6MR
From: Bill Fenech<mailto:w
Probably have to wait for the K4…
Ken K6MR
From: bill steffey<mailto:n...@arrl.net>
Sent: Friday, August 4, 2017 17:13
To: Elecraft Reflector Reflector<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] pre- distortion on k3???
Now that we will have a tx sample out on the back of
Yes. Use the Elecraft KPA500 remote software
http://www.elecraft.com/k2_remote.htm#k3remote
You can run it client/server if you have a PC on the remote end or use a serial
or USB server.
Ken K6MR
From: k...@gmx.com<mailto:k...@gmx.com>
Sent: Friday, July 28, 2017 10:50
To: el
level should be.
Ken K6MR
From: Jim N7US<mailto:j...@n7us.net>
Sent: Sunday, July 16, 2017 10:55
To: Elecraft Reflector<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] [K3S] Soundcard levels
The Windows recording and playback levels of the soundcard in my K3S seem to
both be ve
an interface that let you move
the controls around on the screen. Pretty much build any front panel layout
you wanted.
Ken K6MR
From: K9ZTV<mailto:k9...@socket.net>
Sent: Tuesday, May 30, 2017 5:25 PM
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft
info the better. I don’t
do assisted (no distracting band map) and my favorite contests are Sprints.
Just pure radio with a little technology to record the results.
Getting a bit OT here so I better quit before Eric finds out….
Ken K6MR
From: Buddy Brannan<mailto:bu...@brannan.name>
Sent: T
and click. This is radio, not a
video game.
And now back to your regular conversation…. ;^)
Ken K6MR
From: Phil Hystad<mailto:phys...@mac.com>
Sent: Tuesday, May 30, 2017 3:18 PM
To: Thom<mailto:k...@ki8w.com>
Cc: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject:
Uh, No. CI-V is a CSMA-CD type of system, with station addressing. RS-232 is
nothing like it. You can’t just put RxD and TxD on the same wire. Data format
is way different.
Ken K6MR
From: Nr4c<mailto:n...@widomaker.com>
Sent: Sunday, May 7, 2017 10:56 AM
To: barry whittemore<m
I believe the most important item to note is the “TX SAMPLE” jack on the rear
panel. That has SDR written all over it.
Ken K6MR
From: Kevin Stover, AC0H<mailto:ksto...@ac0h.net>
Sent: Friday, May 5, 2017 3:26 PM
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
My “Aux” cable is about 25 feet long. It’s just a CAT5 cable wired
appropriately. Works fine.
Ken K6MR
From: Harry Yingst via Elecraft<mailto:elecraft@mailman.qth.net>
Sent: Friday, May 5, 2017 9:38 AM
To: Michael Walker<mailto:va...@portcredit.net>
Cc: elecraft@mailman.qth.net<
.
Ken K6MR
From: Harry Yingst via Elecraft<mailto:elecraft@mailman.qth.net>
Sent: Thursday, May 4, 2017 8:02 PM
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [Elecraft] Remoting the KPA500 & KAT500?
More and more I'm considering remoting my KPA500 out of
Turn off the VFO lock. Hold the rate/lock button.
Ken K6MR
From: KG7FYI<mailto:stan...@surcp.org>
Sent: Saturday, April 29, 2017 11:04 AM
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft] K3 P3 and KAT500
Thanks Matt. Nope all bands are set to In.
It’s just you: http://www.isup.me/elecraft.com
It's just you. http://elecraft.com<http://elecraft.com/> is up.
Ken K6MR
From: Ian Kahn<mailto:km4ik@gmail.com>
Sent: Friday, April 28, 2017 7:06 PM
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: [
1 - 100 of 143 matches
Mail list logo
