I am using the Times Microwave connectors on Times Microwave LMR-400 for my HF
antennas. Except a Belsen 8267 jumper around the rotor to Yagi. The Times
Mocrowave connectors for RG8, 214, 214, 9913, and LMR400. I had the LMR400 left
over from a job so no cost except the UJF male and one UHF
On 7/12/2021 9:34 AM, Bill Steffey NY9H wrote:
I'll bet he meant Amphenol
Yes. Bad fingers!
73, Jim
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
No question about that, but my comments were with respect to coax other
than hard line.
73, Jim K9YC
On 7/12/2021 8:09 AM, j...@kk9a.com wrote:
So does Andrew/Commscope.
John KK9A
WO2X wrote:
Times Microwave also make good connectors. We use them on UHF, but most cables
we make are
5/32” inches is 0.156” which is 3.968 mm. So if the Asian manufacturer
considers 4 mm easier and close enough the pin will be oversize.WW II
drawings give the pin diameter as max/min 0.158/0.154 . 5/32 is right in the
middle of this range. I don’t have the MILSPEC documentation but guess
Probably! Belden cable with Amphenol connectors ...
Hugo
Message d'origine
De : Bill Steffey NY9H
Date : 2021-07-12 12 h 34 (GMT-05:00)
À : Hugo Loranger , elecraft@mailman.qth.net
Objet : Re: [Elecraft] KAT500 ANT1 problem
I'll bet he meant Amphenol
On 7/12/2021
...@audiosystemsgroup.com>>
To: elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>
Subject: Re: [Elecraft] KAT500 ANT1 problem
Message-ID:
mailto:ec5ede20-52e9-33a4-677a-2fd2c60fd...@audiosystemsgroup.com>>
Content-Type: text/plain; charset=utf-8; format=flowed
On 7/11/2021 1:52 PM,
>
Subject: Re: [Elecraft] KAT500 ANT1 problem
Message-ID:
mailto:ec5ede20-52e9-33a4-677a-2fd2c60fd...@audiosystemsgroup.com>>
Content-Type: text/plain; charset=utf-8; format=flowed
On 7/11/2021 1:52 PM, Dave wrote:
> What had apparently happened was that I had a batch of the of
Yes, Andrews especially for Heliax hardline
73
Dave wo2x
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of j...@kk9a.com
Sent: Monday, July 12, 2021 11:09 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 ANT1 problem
So does Andrew/Commscope
So does Andrew/Commscope.
John KK9A
WO2X wrote:
Times Microwave also make good connectors. We use them on UHF, but most cables
we make are designed to be put in place semi-permantly.
73
Dave wo2x
Sent from my iPad
> On Jul 12, 2021, at 12:07 AM, Jim Brown wrote:
>
> On 7/11/2021 1:52 PM,
A PL-259 should have a 5/32" (4mm) pin.
John KK9A
kd4iz wrote:
What had apparently happened was that I had a batch of the offshore made
"Amazon Special" PL-259s that appear to have a slightly oversize center pin.
The patch cable used until recently had one of them on one end. It had
spread
Times Microwave also make good connectors. We use them on UHF, but most cables
we make are designed to be put in place semi-permantly.
73
Dave wo2x
Sent from my iPad
> On Jul 12, 2021, at 12:07 AM, Jim Brown wrote:
>
> On 7/11/2021 1:52 PM, Dave wrote:
>> What had apparently happened was
On 7/11/2021 1:52 PM, Dave wrote:
What had apparently happened was that I had a batch of the offshore made
"Amazon Special" PL-259s that appear to have a slightly oversize center
pin.
For several decades, I've served on the Standards Committee of the Audio
Engineering Society with
"The secondary toroid of the directional coupler has a direct path to ground.
That means there is no straight-through DC path."
I may have misunderstood the schematics. What I see is a DC path between J1
input and "ATU". If K20, K21 and K18 are all in the NC state there will be a
low
Andy, my friend, you are forgetting something. The secondary toroid of the
directional coupler has a direct path to ground. That means there is no
straight-through DC path.
Rare that I catch Andy on something…
73,
Jack, W6FB
> On Jul 11, 2021, at 6:12 PM, Andy Durbin wrote:
>
> KAT500
ent: Sunday, July 11, 2021 14:07
To: kd...@frawg.org
Subject: RE: [Elecraft] KAT500 ANT1 problem
Jack,
The KAT500 schematic is on line (partial)
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page1.png
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page2.png
https://www.qsl.net/wb
Don,
Already gone and replaced...
Jack - KD4IZ
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Don Wilhelm
Sent: Sunday, July 11, 2021 17:07
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 ANT1 problem
And discard those "Amazon Special" PL
July 11, 2021 14:07
To: kd...@frawg.org
Subject: RE: [Elecraft] KAT500 ANT1 problem
Jack,
The KAT500 schematic is on line (partial)
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page1.png
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page2.png
https://www.qsl.net/wb4kdi/Elecraft/KAT5
-
From: kirk.hard...@k6kar.com
Sent: Sunday, July 11, 2021 14:07
To: kd...@frawg.org
Subject: RE: [Elecraft] KAT500 ANT1 problem
Jack,
The KAT500 schematic is on line (partial)
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page1.png
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA
@k6kar.com
Sent: Sunday, July 11, 2021 14:07
To: kd...@frawg.org
Subject: RE: [Elecraft] KAT500 ANT1 problem
Jack,
The KAT500 schematic is on line (partial)
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page1.png
https://www.qsl.net/wb4kdi/Elecraft/KAT500/KAT500_RevA_page2.png
https://w
19 matches
Mail list logo
