Folks,
$90 shipped CONUS--includes camera complete with all the manuals and
cables; Canon DK110 power supply/batt-charger; a new battery; and 2
compact flash cards one 8Mb the other 64 Mb. Everything is in near new
condition.
This is a great camera for the many TTF events coming up. The S10
I have a KIO2 serial port for the Elecraft K2 transceiver for sale. This
one has not been hooked up to a computer so I really can't verify if it
works. All of the voltages and checks are correct by the instruction
manual. I have no reason to believe that anything is wrong with it. My
Hi Craig,
The problem with ear buds is that they do not fit my ears. I have tried
many of them. They hurt terribly. Also I have to press them forcibly
against my head to get the best around. That's why I will try the Koss
type that have the narrow sound pipe and the compressible foam around
I am finishing a KX1 and have a question. When tuning the radio, there is a
LOT of DDS hash when turning the tuning knob. I am just finished with the 20
meter and 40 meter testing. Will this always be there? Is there a way to
reduce this?
Jess EACH
I'm building my K2, #4759, in page 53.
The fifth step in page is:
Install the BFO crystals X3 and X4 (near J7). Important: trim X3's
leads, and fold them down flat against their pads, before soldering.
Then use a minimal amount of solder. This is necessary to avoid
interference between X3
Yves,
That is UNBELIEVABLE !
Did the parcel go through Canada Customs, or somehow get bypassed?
Everytime I order anything it takes 14 to 20 days to arrive, even small
envelopes of parts.
Did you use US Mail Service?
73, Bob VE3XM
___
Elecraft
Hi All
I was measuring the gain difference of the OP1 x-tal filter and the
CW filter on my K2.
It seems that the OP1 filter has +10dB more gain than the CW filter
I have the 2.5kHz OP1 filter mod and the stock CW filter on 2.4kHz.
Measurements are done on 7 MHz band on LSB.
I did the
The KIO2 has been spoken for.
Thanks
Brent
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Just a quick note to acknowledge all who checked in last evening. This was our
second week operating at 0100z - but with daylight savings time, it looks like
quite a few more folks from the west coast checked in.
CALL NAME ST RIG SNRST Sent
== = == = =
Marteinn Sverrisson wrote:
I was measuring the gain difference of the OP1 x-tal filter and the
CW filter on my K2.
It seems that the OP1 filter has +10dB more gain than the CW filter
I have the 2.5kHz OP1 filter mod and the stock CW filter on 2.4kHz.
Measurements are done on 7 MHz band on LSB.
Marteinn,
The CW filter has a greater signal loss than the OP1 filter mainly because of
it's varicap variable bandwidth design. My K2 has about a 6dB loss relative to
the OP1. Your CW filter loss of 10dB may be a bit high. I would check the
varicap lead orientation.
73
Stewart G3RXQ
On Fri, 8
K6DGW's KX1 S/N is #897. I guess it got lost in transmission. I was
surprised at the signal strengths out here on the frontier ... NK8Q was
easily a real 569 as was Daniel. 0100Z works pretty good for us PDT
types unless we have family or friends over for dinner.
73,
Fred K6DGW
Auburn CA
Dan,
Thanks for running the net. My first ECN/30 check-in. Was glad to hear Steve,
N7VS whom I had worked a couple of weeks ago when I was at Pulpit Rock for
MoonLight Madness with EPA QRP Club. I was calling him to let him know that
during the net I was finally finishing the QSL card for
Marteinn Sverrisson wrote:
Vic and Stewart, Tanks for answering
well, the ripple on the CW filter at 2kHz BW is abt 8db p-p.
the gain difference when the CW filter is offset to 1.2kHz
(for digital modes) and its BW is 1kHz is abt -3dB relative to
the OP1 filter (not bad?).
with the same at
Thanks to all who replied regarding using OSHA ear plugs on ear buds to
keep them in. Not sure why I couldn't find it in the archives ... short
attention span while searching, I guess.
73,
Fred K6DGW
Auburn CA CM98lw
___
Elecraft mailing list
Post
Hi all,
I am selling a K2, built by me. It includes SSb adapter, 160M/RX
adapter, Noise blanker, AF filter, 60M/xverter adapter, KAT2 tuner, and
Elecraft hand mic. Will sell for $1000.00 shipped anywhere in the lower
48 of the US.
Please do not reply on this list, send email to:
[EMAIL
Hi all,
Well spring is in the air and old man's fancy turns to antennas.
I have a K2 (s/n 1103) without the 100 watt amp and with the internal low
power ATU. Unless procrastination gets the best of me again, I'd like to string
up a new wire antenna this spring.
I have a chunk of 400
Thanks all
I checked T7, it is OK, so are the varcaps. My K2 seems OK
I fiddled with the CW filter settings, changed the BW and it does indeed
show the expected behavior, to much bandwidth 1kHz, to little bandwidth
200 Hz did show lower filter gain, so I just selected BWs which
do not have
-Original Message-
From: W3FPR - Don Wilhelm
I put the tiny LED in the SPOT button, I figure its function is more
intuitive in that position.
--
This is neat and something I've been looking for for a long time - a
solution for indicator lights for those of us
Hi Folks:
I have just posted a slightly edited copy of Don's alternate LED
installation instructions on my web site www.n0ss.net right below the
docs for assembly and alignment of the CW Tuning Indicator.
Over the next couple weeks, basically as soon as Don comes up from Income
Tax
I have found that some ear buds fit better if you switch them to the other
ear, or turn them slightly so that the wire exits at an angle to the rear of
the head.
Maybe you can find a more comfortable position that way.
On another headphone note: From time to time, I report on using Cosmetic
Stuart Rohre wrote:
On another headphone note: From time to time, I report on using Cosmetic
Sponges as cushions for old fashioned headphones of the high impedance
bakelite type. Besides Walgreens drug Store, I have found some of the
local Dollar Stores carries 8 White sponge disks for
Hi Vic,
The diameter of the cosmetic pads I have found is smaller, (slightly) than
the Trimm type and Military Surplus phones I have used them on. I do wear
glasses 100 per cent of the time, and these pads have not been a problem.
They do not stick out forward of the ear enough to touch the
From time to time, discounts appear on the Weller PT tips
(which is the temperature sensor function of this soldering station)
The eBay store for esoutlet is offering a wide variety of PTx tips for
$2.99 each.
For example, Item number: 3874077906 (PTL tip) with a selection of 600, 700 or
800
Just worked SP0PAPA, special even station(s) in Poland commemorating the life
of Pope John Paul II on 40m. The operator was working split and there was a
pileup. I had just finished raising one end of my windom antenna a bit
higher and brought the center back up since the winter winds are
I got a pair of these for Christmas.
http://store.yahoo.com/earplugstore/chmisearph.html
Very good fit!
Jeff Burns
AD9T
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Steven Pituch
Sent: Friday, April 08, 2005 7:57 AM
To: 'Elecraft Reflector'
May be out of order on this reflector, but yesterday I had a mssage to post
concerning a big trouble with my K2 SN 4498 and the following was all what I
got in return...!!! So what can I do to post an e-mail from
Europe?
Thank you very much for the pass band ! F5UL
27 matches
Mail list logo
