yep there is one under development but I am not sure when it was due, last
call I had with the developer was in the summer and he was a long way off
there was also work on a 4m version too (mod of 6m)
rgds
Simon DL4PLM/GM4PLM
From: Doug Shields [EMAIL PROTECTED]
Reply-To: Doug Shields
James T. Jim Rogers, W4ATK wrote:
I have not been sucessful in sending CW via the CAT interface.
DTR always off
RTS always off
Hi Jim,
I have DTR and RTS always on. Everything else is the same except I run
mine from a USB port through a
So K2 Gentelmans...one question..
To fix RF switching problem in KPA100 there are 3 way's available (posted)
1. 12pF to ground from 1n4007's junction (just mooves a problem arround)
2. 1K resistor instead of RFC3 (affects RX preformance and marginal
switching at high power levels)
3. Change
On Thu, 13 Jan 2005 15:16:53 +0100, S55M wrote:
So K2 Gentelmans...one question..
To fix RF switching problem in KPA100 there are 3 way's available (posted)
1. 12pF to ground from 1n4007's junction (just mooves a problem arround)
2. 1K resistor instead of RFC3 (affects RX preformance and
I have been given the electronic of such a unit? Does anybody know if
there are suitable enclosures available?
Regards
Ed
On Wed, 12 Jan 2005 14:55:18 -0500,
[EMAIL PROTECTED]
[EMAIL PROTECTED] wrote:
I can heartily endorse the AADE LC meter ( see http://www.aade.com/)
I received a kit
I have built 80 K2's to date. Let me build one for you. My prices are
reasonable and you receive a completed K2 ready to enjoy.
73
Alan
W1HYV
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Go to http://www.aade.com/ and ask
if you can buy just the housing.
Good luck and 73
Bob N6WG
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Adi,
Stewart Baker G3RXQ has also been fighting this problem and he sent me a
note a week or so ago saying that he understood that on Dec 14th Eleraft
issued an Errata for the KPA100 which changed R4 in the HV osc from 100k to
39k and ** added a 1k resistor in parallel with RFC3 ***. There
B. Scott Andersen [EMAIL PROTECTED] wrote :
4. I'm drooling over the hex paddles now advertised on the
Elecraft web site. It looks JUICEY! But, I would want it to
be the key that travels with the radio. Does anybody have this
item? If so, could you render an opinion about how well it
might
Finally had a chance to work on some of my kits.
I had completed the DSP kit and just now am installing
it.
No smoke
That's good!
but the red LED remains on.
That's not so good.
...
Any suggestions?
The LED comes on when the DSPx resets, and goes off when it handshakes
with U1 on the
I know I ask this beore, but do not remember as response. Is there, was
there, a K2 to Argonaut V side by side ever done
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr.
I just heard a radio Commerical,
by the ARRL promoting amatuer (ham) radio.
FAR OUT
de rc kc5wa
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 265.6.11 - Release Date: 1/12/2005
___
Elecraft
-Original Message-
There is an Errata from Elecraft which does not appeared to have made it
onto their Web site yet. It is:-
---
K2/100 MANUAL (Appendix G) ERRATA
Rev. C-3, December 14, 2004
On Jan 13, 2005, at 10:25 AM, William E. Twaddell wrote:
I know I ask this before, but do not remember as response. Is there,
was there, a K2 to Argonaut V side by side ever done?
Hi William (Bill?),
There probably are independent comparisons out there somewhere.
Meanwhile, both the K2 and
Hi
My KIO2 has just stopped communicating.
Osc is OK, neg volts -10
Volt checks look OK except for
U1 Pin 5 which is 13 should be -8
U1 Pin 12 is 0 should be 5?
BUT U1 pin 5 goes to the TXD line and thence to the control boards U6 pin 25,
which is shown in the Manual as being at 0
Thanks for the suggestion Lyle. I'll check that out. I
didn't have a speaker or headphones connected. From
the SEC menu, I was not able to turn the DSP on.
73,
Julius
n2wn
--- Lyle Johnson [EMAIL PROTECTED] wrote:
Finally had a chance to work on some of my kits.
I had completed the DSP kit
Hi William -
If you are a member of the ARRL you can download the reviews of each radio
plus the detailed reports too.
I've owned an ArgoV, Orion and K2.Orion had best receiver but did not
copy anything during close-in contest QRM/DX pileups that the K2 couldn't
copy too.
The ArgoV was poor
Since this list is a font of everything electronic, can y'all help me with
this?
I've got a HP DC power supply (6443B) that's worked great for a long time. I
DON'T have a service manual for it (of course). Recently, when I turn this
thing on, the voltage comes up, then drops off slowly (this
I'm not sure what the question is, but those look like 4500 micro-farad, 150VDC
electrolytic caps. What would the HP manual tell you about them?
On Fri, 14 Jan 2005 09:12:18 +1200, Richard T. Perry
[EMAIL PROTECTED] wrote:
Since this list is a font of everything electronic, can y'all help me
4500 Microfarad 150 Volts DC
-Stuart
K5KVH
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Richard,
That is a 4700 uF 150 volt capacitor. You may not be able to find an exact
replacement, but do check the mounting and the size that will fit. You are
seeking a replacement capacitor that will fit into the available space and
can be properly mounted - the capacitance should be
Hello all,
The ARCBS Toy Store is open! This is where members and non-members will
find covered bridge and amateur related items.
The new ARCBS World Guide to Covered Bridges 2005 is there!
Check it out at:
http://www.arcbs.org/files/ARCBSadministration/ARCBStoyStore.html
72/73,
Ed,
I've always experienced low RF output on SSB from my K2/100 when using my Heil
ProSet Plus headset.
While building my KAT-100 I also upgraded from 1.02 to 1.09 firmware on the
KSB2 board.
WHAT A DIFFERENCE!Now I get full power output on all bands in SSB mode.
The sheet that comes with
My K2 number 4245 is finally on the air. I bought the kit at Dayton
then within two weeks changed jobs and moved half way across the state.
The kit sat unopened until November of last year, when I finally got
through with the moving in, honey-do tasks and set-up of a work shop to
begin
Hi Group,
I've just recently finished a K2, S/N 4630. It has DSP, SSB, 160M
Option,KI02 and the K60XV.
All appeared well until today, when I noticed that tapping the DISPLAY
Button from the frequency display to the DSP Menu, I get a cyclic
beep...or burp. It changes frequency from DSP on
It happens to everybody...you just can't stay in the DSP menu when you
are receiving. The DSP manual explains it; it is the noise of the
auxbus communications which are normally done only with the RX muted and
infrequently.
___
Elecraft mailing list
26 matches
Mail list logo