Martin ,for the bad results of K2+Transverter probably both of them
contributed.
My first try with transverter+K2 was in Marconi CW contest (November
2004).Before that i used FT1KMP and Javornik transverter.
Other stations told me, that i was very noisy over a whole 2m band while on
TX.
At that
Hi all,
#4044 has died. It simply stopped working during the ARRL contest last
weekend. It does not receive, transmit or speak to the PC. I have
tried a full reset to no avail and I have removed the PA. The fault
seems to lie on the rf board somewhere and I would appreciate some
pointers. I
David, I replied to this once but didn't see it show up so if it shows up
twice, I apologize.
I would disagree with you on your suggestion.
One of the things that makes contesting a little easier (sometimes) is that the
exchanges are publishes, so you know what to expect next.
How many times
On Fri, 2005-03-11 at 10:08 +, Ian J Maude wrote:
Hi all,
#4044 has died. It simply stopped working during the ARRL contest last
weekend. It does not receive, transmit or speak to the PC. I have
tried a full reset to no avail and I have removed the PA. The fault
seems to lie on the rf
Ian,
It is difficult to say where the problem might be when all I really know is
'it is broken'.
The best place to start is to determine what does work. Do you have
voltages anywhere (check input and output of the regulators on the control
board)? Are the voltage readings good (compare with
On Fri, 2005-03-11 at 11:54 +, Ian J Maude wrote:
I really should have added that the on/off, display, menus etc all
work.
The K2 sees the additional boards etc so it would seem that DC power
is
not the problem.
ok, getting there. I decided as I had already done a reset that I would
On Fri, 2005-03-11 at 12:19 +, Ian J Maude wrote:
Problem solved. Thanks to all that enailed with help. As I suspected
it was down to a poorly soldered joint. I warmed up quite a few
connections in that area to be honest so I cannot be sure which did it.
The main thing is that everything
I know this is a bit long but it so represents the spirit of this
reflector, I just had to pass it along. Enjoy. As one of Jeff's Elmers I
know I walk a little taller after reading this.
73s Jim, W4ATK
Find the Golden Thread in BARC
By Jeff Drew, N4JDU
There is a value to club
Someone once wisely suggested picking a non-cardinal frequency for the ECN -
and I think I really need to heed that advice next week - so watch for an odd
frequency (e.g. 10118.7) for the net next week.
Running QRP-10W has it's disadvantages - especially when a DX station
(TO7K/TO7C?) starts
Mike:
Well, I agree that my suggestion to use the short-hand response is
not that good, but not for the reason you give. Wayne correctly
pointed out that it would confuse informal participants, and I think
that is true. However, your concern does not really have force. Since
non-Elecraft
Hello Dwight,
The External PA Key jack does not source current to drive a relay;
rather, it sinks current from the relay, so you essentially connect your
relay between the +12 volt source and the External PA Key jack. So, if
what you're asking, is how to connect an external relay with a 12
I read this reflector via AC6RM's excellent online service.
Is there an option to cut out most of the various List... headers so I
don't have to scroll down the page for each message to see the actual text.
--
Julian, G4ILO
G4ILO's Shack: http://www.tech-pro.net/g4ilo
Hi Martin,
I don't use samba much so I'm not positive what the problem is, but do a
man lpoptions if you're using CUPS to manage your print services. It
sounds like you might want to do something like lpoptions -o
job-sheets=none to turn off banner page printing. If you're not using
CUPS,
Hi Lee,
Something that I have used in the pass was a PL259
fitted with a 6-32 (I think that was the size) brass
threaded rod or a long screw with the head removed.
Solder it to the center pin, close off the ground
holes with tape and fill the body with epoxy. This
leaves you with a threaded
W3FPR - Don Wilhelm wrote:
If the tone pitch change is 20 Hz or less it is because of the quantizing
error in the K2 and nothing can be done about it. The K2 firmware works to
preserve the pitch no matter where the filters are set as long as the signal
is anywhere within the filter passband.
Sold my K2 last year and never installed the following:
BFOMDKT Toroid/PLL xtal upgrade
E850006 Match xtals(7) CW
K2KSB2XTLS Match Xtals(14)
XFILMDKIT 2nd Filter upgradetotal cost $47.00
asking $35 shipped CONUS
Ron
Thanks all.
ROn
_
Express yourself instantly with MSN Messenger! Download today - it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
___
Elecraft mailing list
It looks like your RBW is way too high, which will increase the apparent
noise level by a large amount. It should be set to 100 Hz also. Set your
sweep to auto so it will go slowly enough to make the measurement. It
will take some time for the sweep.
73, Eric
S55M wrote:
Hy Eric!
Thanks
Just a quick reminder that the Elecraft QSO Party starts tomorrow at
1500 Z and runs through Sunday at the same time. The bands are open
here today -- with any luck they will be tomorrow, too.
Details at:
http://www.elecraft.com/Awards/eqp_2005.htm
I'll be trying to make QSOs on all
Tom Juelich wrote:
I am just wondering what for are C78 and RFC8 on the RF
board? They are only supplied with the 80m kit.
I don't remember what Gary Surrency at Elecraft said about the problems that
were found on 80m that required these components. You could email him directly.
I just went
OK, I am cutting thru this I/O kit like butter. Should have it done in
another hour.. I am very interested in what type of software is available.
Of course like everybody else, I want the rig on the laptop for control
and display.
I am ultra interested in hidden menues or CPU instruction
I have a like new K2 serial no. 349X for sale. It included the KSB2 and KAT2
adapters and all paperwork. It works great! I want to build another and that
is why I am selling. This is the second I have built. I am a retired
electronics instructor and have built many, many kits and homebrew
22 matches
Mail list logo