Hi,
this weekend from Saturday 13.00 UTC to Sunday 12.59 UTC is the Region
1 SSB Field Day. So keep your ears open for puny signals coming from
our side of the pond! This year our local club will be running Field
Day stations at three different QTHs simultaneously.
For more information
Hm. a perspective from the other side of the Pond.
On the contrary, I found conditions pretty reasonable on 20m at the
weekend. I had a go at the SCC RTTY contest and got most of your East
Coast regulars, plus some far-east Siberian stuff and north of South
America.
If that's bad
hb9ari wrote:
I work essentially with JT65A mode; as this mode
is a single tone mode, i've set the modulation
level just before full ALC and power to 50W
(for DX only...). At the beginning of a
JT65A transmit sequence, the power start
at ~ 25W and go up to ~ 48W in 3 to 5 sec.
I'm
hb9ari wrote:
Hi Trev,
Since the beginning, i always get the same behavior
with my K3 #1212 (factory build). I work
essentially with JT65A mode; as this mode
is a single tone mode, i've set the modulation
level just before full ALC and power to 50W
(for DX only...). At the beginning
hb9brj wrote:
I'm active in WSPR mode, which is a single tone as well.
Mode = DATA A, ALC = 4 bars, PWR = 5W.
An external wattmeter shows an absolutely steady power throughout the
entire 2-minute TX cycle.
The bottom cover just underneath the LPA gets pretty hot, but at 5W the
KPA3 is
Hi Markus,
you prabably know but maybe good for the others trying WSJT/WSPR:
You can try very simply power levels per tone by using WSJT menu Setup
- Generate messages for test tones.
Then you have @A - @D and @1000 and @2000 in TX1 - TX6 windows
You can test each tone separately and try to
Hi Julian,
I don't remember the reason(...) but i work
in USB mode. I will try to work in DATA A
mode this week-end and at the same time,
recover the reason for the USB mode choice!
(i read that somewhere!)
For the ALC, i set the level just before the
end of variation (if i'm correct, as i'm not
Hi Lexa,
Very good info, i will do some tests this week-end.
At the same time, a verification of the audio level
response (WSJT/Sound card) should be a good precaution...
73 QRO de Rudolf, HB9ARI
Alexandr Kobranov wrote:
Hi Markus,
you prabably know but maybe good for the others trying
Julian, G4ILO wrote:
It would be nice to have the option to leave the KPA3 in at low power. I
avoid using QRP for high duty cycle modes because I'm afraid it stresses
the radio more than using 12W does.
Julian, you can force the KPA3 to stay on by means of a workaround:
Set PWR = 15W,
Ok! It's in the to do list!
73,
Rudolf
Alexandr Kobranov wrote:
Absolutely!
One thing is to have uniformity of power out (this is what we need as
a final), the other is to know levels of AF out per tone from the
sound card and then characteristic of the rest of line.
Let me know your
Trev,
You're Welcome!
As written, i've also to work on the problem...
73,
Rudolf
TREVOR WATERS wrote:
Rudolf,
Many thanks for the reply to my post. Still working on the problem here.
Many thanks for your thoughts
Gud DX Best 73
Trev GW4IMC
--- On *Wed, 2/9/09, hb9ari
...you can force the KPA3 to stay on by means of a workaround:
Set PWR = 15W, then define actual TX power using MIC gain.
This will most likely result in the radio's long term ALC gradually
increasing gain in the transmit path until it either (a) runs out of
gain or (b) hits it
Hello all,
I am wanting to buy a K3 and need to sell my loaded K2.
The serial # is 3644. I have used the rig for receive only as I never finished
the transmitter alignment.
My ears could not discern a difference in tone. The soldering is professional.
The options have never been
Dear all,
Problem:
Low output on RTTY and PSK31 on 80 meters using the mode DATA-R and output
from sound card.
Situation:
Starting on 15 meters running RTTY or PSK31 with an output of about 85 W.
Using Ham Radio Deluxe switching to 80 meters, also switching antenna.
The output falls down to
Thanks to Gordan and Larry.
I do not run the station hot. Max temp seen has been 73 degrees centigrade
(auto shut down is at 85 C). Most of the time max temp is 67 C.
I do have the same number of ALC bars on 80 meters as on 15 meters.
Increasing the output from my sound card just made the
On Sep 2, 2009, at 9/29:26 AM, Kjeld Holm wrote:
Just now I noticed that for the last second or so of the
transmission it
seems like I have full output also on 80 meters. BUT it is not a
question of
warming up as the full output is seen only for the last second
whether I am
K3 beta-test firmware revision 3.30 (with DSP rev. 2.26) is now
available. See release notes below.
Please send problem reports to k3supp...@elecraft.com. Beta firmware
load instructions can be found at
http://www.elecraft.com/K3/k3_software.htm
73,
Wayne
N6KR
* * *
MCU 3.30 / DSP
Bingo! SubRX NB working at last.
Thanks heaps!
73
Glenn ON4WIX
- Original Message -
From: wayne burdick n...@elecraft.com
To: Elecraft Reflector elecraft@mailman.qth.net
Cc: elecraft...@yahoogroups.com; elecr...@yahoogroups.com
Sent: Wednesday, September 02, 2009 7:59 PM
Subject:
Good afternoon, Folks.
First off, I have NO COMPLAINTS WHATSOEVER on my K3/100 - Kit [S/N 2802]!
I have five Filters installed [the bandwidths of which I won't mention fearing
massive retribution - but personally they suite me just fine as I'm a
CW operator only!], the Ant Tuner and the
On Wed, 2 Sep 2009 13:10:25 -0700 (PDT), James Harris
capo...@bellsouth.net wrote:
Good afternoon, Folks.
First off, I have NO COMPLAINTS WHATSOEVER on my K3/100 - Kit [S/N 2802]!
I have five Filters installed [the bandwidths of which I won't mention fearing
massive retribution - but
Excellent work -- best of both worlds. Exactly what I was hoping for!
Now if only PB CTRL SHIFT=.01 had the same 0.40-2.60 FC range as SHIFT=.05
... (nudge)
;-)
73,
Paul WW2PT
wayne burdick wrote:
* MORE NR (NOISE REDUCTION) SETTINGS: There are now 32 NR settings.
F1-x to F4-x
Good afternoon, Dick.
Thanks for you quick reply.
a.) - I have a straight through 9 male pin to 9 pin female cable.
b.) - As far as I know, the cable isn't a special USB-to-Serial Cable. I have
checked it with a meter and there is straight-through continuity on all pins:
no groundings or
I think you're using a USB to Serial Adapter in addition to a straight
thru 9-pin male to female connector.
The Keyspan 19HS is a USB to Serial Adapter. COM4 is the port you're
loading the K3 through, right?
If your personal computer has any free serial RS-232 ports (the 9-pin D
male
Hi, Dick.
Maybe I need to describe my setup a bit more thoroughly.
I do not have a Serial Port of any kind on my DELL laptop computer: hence
trying an Adapter.
So yes, I'm using a KEYSPAN USB-to-Serial Adapter with a straight through
9-pin male to 9-pin female cable to my K3.
But
But the reliance on insulation rather than grounding for safety seems to be
bringing us back many unsafely grounded outlets. It's now very common to
have even brand new construction, signed off by all the appropriate
inspectors, turn up reversed wired outlets and missing grounds.
Electrician
Ken,
While 160 meter receive may seem good, the bandpass filter may still
have a problem.
I would first try to isolate the problem - turn the manual to appendix E
page 14 - set the transmit power for 5 watts and check the RF voltages
with your RF Probe at the points listed (Transmit Mixer,
Jim,
Given that you are using a laptop with no serial ports, a USB-to-serial
adapter is probably your simplest option. There are such things as PCMCIA
serial cards, but there is no guarantee that one of them wouldn't give you
just as many problems. You might have better luck with a different
I've messed with quite a few of these adapters and one of the most rock
solid ones I've used are the chipsets from FTDI. You can read about their
stuff at http://www.ftdichip.com. I have no affiliation with the company
other than that I've designed a few of their parts into systems that I've
a simple question with probably an obvious answer, but that's why i
get paid the big bucks!
i've been running my K3 off one power supply and measured the voltage
at Pin 2 of the ACC at 4.96, so that's what i set up in the CONFIG.
today i got one of the tiny Gamma HPS-1a supplies (its so small
I normally use a headset while operating. Now that I'm dabbling with RTTY
there seems to me little need for this, however, I would still like to hear the
audio while tuning around.
My headset is plugged into the rear headphone and mic jacks and is a pain to
unplug so I've set the config to
30 matches
Mail list logo