Hi there!
I was totally happy when I found this patch through the wiki.
Everything went pretty smooth. After i found the right firmware,
scanning in Kaffeine worked for me.
But there is another question:
This USB Stick is a hybrid one. Due to this i also gave xawtv a try, but
after some
Hi hans, thanks for the idea, but the result is the same. I extracted the
firmware for the windows driver using your tool and when I use it, it seems
to work except for a repeating message of;
dvb-usb: error while querying for an remote control event.
I think they have an other .sys for the
I got it I remembered that on PCTV DVB-T 72e they had a similar problem,
which was solved leaving GPIO6 to 0. Doing this the tuning seems to work
fine. SNR is always reported as 0% but I think this is not a problem, now I
can scan and tune dvb-t channels. Firmware is 1.10 and xc3028-v27 with
Albert,
I am happy to hear that your TV-card finally works.
However, I am still a bit unsure about these GPIO settings. Initially, I just
copied the GPIO-settings from another entry and
then left it because it seemed to work. Now, I have digged a little bit into
this issue and found, that under
Hi Hans, with this configuration it does not work. As I commented it seems
that it does not work if GPIO6 is set to 1. If I change to 0 it works fine.
Just one comment, GPIO0 for sure is the LED output of my card. :P
Albert
2008/2/17, Hans-Frieder Vogt [EMAIL PROTECTED]:
Albert,
I am happy
For what I understand, changing the Firmware 64 to 6200 changes the if
frequency to 5.2MHz. So this modification on the firmware should make the
card work. What it's more strange for me is that when trying to scan no
signal or SNR is reported, so it seems like xc3028 firmware is not working
Albert,
your dmesg-output looks absolutely fine for me (besides the already discussed
xc2028 4-0061: Error on line 1063: -5
message).
Since you also obvisouly succeeded to patch the xc3028 firmware so that the
scode can be loaded (which in my
cinergy did not make any noticeable difference), I
Hi Albert,
On Thu, 14 Feb 2008 21:20:32 +0100
Albert Comerma [EMAIL PROTECTED] wrote:
[ 2251.856000] xc2028 4-0061: Error on line 1063: -5
The above error is really weird. It seems to be related to something that
happened before xc2028, since firmware load didn't start on that point of the
Hi Albert, Hi Mauro,
I have successfulli patched and compiled the driver. Im using the terratec
cinergy device and it works fine.
[ 2251.856000] xc2028 4-0061: Error on line 1063: -5
This error message looked very familar to me, so i searched my log and guess
what I found:
Feb 15 20:42:18
Aah now I remember that issue, in fact it is no issue. I was seeing that
problem when send the sleep command or any other firmware command without
having a firmware running. In was, so far, no problem.
Patrick.
On Fri, 15 Feb 2008, Holger Dehnhardt wrote:
Hi Albert, Hi Mauro,
I have
For the DiB7000 the code I sent is requiring a 5.2 IF firmware.
Although it should be possible to recover an offset of 200kHz I would
recommend to use this firmware.
Patrick.
--
Mail: [EMAIL PROTECTED]
WWW: http://www.wi-bw.tfh-wildau.de/~pboettch/
On Fri, 15 Feb 2008, Mauro Carvalho
So, If it's not a problem, any of you could send me the current xc3028
firmware you are using, because mine does not seem to work... Thanks.
Albert
2008/2/15, Patrick Boettcher [EMAIL PROTECTED]:
Aah now I remember that issue, in fact it is no issue. I was seeing that
problem when send the
Hi I've been trying to load the tunner-xc2028 module in debug mode. I send
the results, there's the same error and also some things when loading the
firmware. Hans could you send me your firmware to check that it's not an
error of that (I mean, when I scan there's no signal or SNR, perhaps this
Albert,
your dmesg output looks quite good. In fact, the only line that irritates me is
the line with
xc2028 4-0061: Error on line 1063: -5
This line indicates an i2c-communication problem with the tuner.
As it happens BEFORE the XC3028 firmware is loaded, it cannot have anything to
do with
Hi Hans, thanks for your answer, I say what I tryed;
your dmesg output looks quite good. In fact, the only line that irritates me
is the line with
xc2028 4-0061: Error on line 1063: -5
This line indicates an i2c-communication problem with the tuner.
As it happens BEFORE the XC3028 firmware
The latest dib0700-firwmare is dvb-usb-dib0700-1.10.fw not
dvb-usb-dib0700-03-pre1.fw.
Patrick.
___
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Ok, both give the same error, the only one wich does not report any error is
the 0.1. Thanks.
Albert
2008/2/13, Patrick Boettcher [EMAIL PROTECTED]:
The latest dib0700-firwmare is dvb-usb-dib0700-1.10.fw not
dvb-usb-dib0700-03-pre1.fw.
Patrick.
That's what I supposed... So we must get working the 1.10. Thanks again.
2008/2/13, Patrick Boettcher [EMAIL PROTECTED]:
On Wed, 13 Feb 2008, Albert Comerma wrote:
Ok, both give the same error, the only one wich does not report any
error is
the 0.1. Thanks.
Just because it does not
Finally I got what you mean... you changed the extract_firmware.pl, but not
only the comment I guess... also the values below. I tested both and the
result is the same as described before, everything seems correct, but I have
some errors on dmesg and nothing is detected on scan (I must try with an
Hi Hans, you where faster than me... I don't understand what you did with
the firmware. I just extracted the xc3028-v27.fw from the win driver as
commented in other threads.
Then I added my card (pinnacle 320cx) to your patch with some
mid-successfully results, this is the dmesg;
[ 8067.028000]
Hi List,
attached is a patch that extends the dib0700 driver to support the DVB-part of
the Cinergy HT USB XE (USB-ID: 0ccd:0058).
Analogue part not tested (and probably also not supported). Remote Control
seems to work (tested with mini remote from
pinnacle).
I use the driver with the standard
21 matches
Mail list logo
