Re: [linux-dvb] illegal bandwith value, driver for Terratec Cinergy DT usb XS
Hi Derk, On 3/10/08, Derk Dukker [EMAIL PROTECTED] wrote: Thank you very much Markus!! Do you also have any idea how to get the Cinergy CI usb working? I live in Holland and most of the channels are encrypted, so I need to use the Cinergy CI usb but I can't find drivers/information anywhere. I bought this in the firstplace for my playstation 3 with linux on it, I knew that support for CI was hard, but they said it would work with eyetv. So I thought, if it isn't working on linux it will on mac with eyetv. Everything works on my mac with eyetv except the CI usb :( there's no support for this CI device at this time. Markus ___ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
[linux-dvb] illegal bandwith value, driver for Terratec Cinergy DT usb XS
The driver in linux kernel 2.6.24.2 for Terratec Cinergy DT usb XS diversity sets the reported bandwith outside the fe_bandwidth_t range. The value 0 (BANDWIDTH_8_MHZ) is replaced with 8000. Here is an example showing the problem... Device: Terratec Cinergy DT usb xs diversity Linux: 2.6.24.2 (modules: mt2266, dvb_usb_dib0700) Firmware: dvb-usb-dib0700-1.10.fw Received event for frontend 0 Status for frontend 0 is now: 0 (no signal) Reported parameters for frontend 0 are now: Frequency: 71400 Hz Inversion: AUTO (2) Bandwidth: 8 (0) High priority stream code rate: AUTO (9) Low priority stream code rate: AUTO (9) Constellation: QAM64 (3) Transmission mode: AUTO (2) Guard interval: AUTO (4) Hierarchy information: AUTO (4) Received event for frontend 0 Status for frontend 0 is now: FE_HAS_SIGNAL (found something above the noise level) FE_HAS_CARRIER (found a DVB signal) FE_HAS_VITERBI (FEC is stable) FE_HAS_SYNC (found sync bytes) FE_HAS_LOCK (everything's working) Reported parameters for frontend 0 are now: Frequency: 71400 Hz Inversion: AUTO (2) Bandwidth: ??? (8000) High priority stream code rate: 2/3 (2) Low priority stream code rate: 1/2 (1) Constellation: QAM64 (3) Transmission mode: 8K (1) Guard interval: 1/8 (2) Hierarchy information: NONE (0) ___ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Re: [linux-dvb] illegal bandwith value, driver for Terratec Cinergy DT usb XS
On Mon, Mar 10, 2008 at 12:59:55PM +0100, Derk Dukker wrote: I also have a Terratec Cinergy DT XS diversity but can't get it working with the Cinergy CI usb, do you have any idea how I can make it work? I don't have any CI units so I haven't tested. ___ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Re: [linux-dvb] illegal bandwith value, driver for Terratec Cinergy DT usb XS
Hi Tero, I also have a Terratec Cinergy DT XS diversity but can't get it working with the Cinergy CI usb, do you have any idea how I can make it work? By the way, they showed on CEBIT a EeePC with linux on it with the Cinergy XSS. They also said that they will release linux drivers for all of their tv tuners. Regards On Mon, Mar 10, 2008 at 12:17 PM, Tero Pelander [EMAIL PROTECTED] wrote: The driver in linux kernel 2.6.24.2 for Terratec Cinergy DT usb XS diversity sets the reported bandwith outside the fe_bandwidth_t range. The value 0 (BANDWIDTH_8_MHZ) is replaced with 8000. Here is an example showing the problem... Device: Terratec Cinergy DT usb xs diversity Linux: 2.6.24.2 (modules: mt2266, dvb_usb_dib0700) Firmware: dvb-usb-dib0700-1.10.fw Received event for frontend 0 Status for frontend 0 is now: 0 (no signal) Reported parameters for frontend 0 are now: Frequency: 71400 Hz Inversion: AUTO (2) Bandwidth: 8 (0) High priority stream code rate: AUTO (9) Low priority stream code rate: AUTO (9) Constellation: QAM64 (3) Transmission mode: AUTO (2) Guard interval: AUTO (4) Hierarchy information: AUTO (4) Received event for frontend 0 Status for frontend 0 is now: FE_HAS_SIGNAL (found something above the noise level) FE_HAS_CARRIER (found a DVB signal) FE_HAS_VITERBI (FEC is stable) FE_HAS_SYNC (found sync bytes) FE_HAS_LOCK (everything's working) Reported parameters for frontend 0 are now: Frequency: 71400 Hz Inversion: AUTO (2) Bandwidth: ??? (8000) High priority stream code rate: 2/3 (2) Low priority stream code rate: 1/2 (1) Constellation: QAM64 (3) Transmission mode: 8K (1) Guard interval: 1/8 (2) Hierarchy information: NONE (0) ___ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ___ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Re: [linux-dvb] illegal bandwith value, driver for Terratec Cinergy DT usb XS
Thank you very much Markus!! Do you also have any idea how to get the Cinergy CI usb working? I live in Holland and most of the channels are encrypted, so I need to use the Cinergy CI usb but I can't find drivers/information anywhere. I bought this in the firstplace for my playstation 3 with linux on it, I knew that support for CI was hard, but they said it would work with eyetv. So I thought, if it isn't working on linux it will on mac with eyetv. Everything works on my mac with eyetv except the CI usb :( Regards, Derk On Mon, Mar 10, 2008 at 4:37 PM, Markus Rechberger [EMAIL PROTECTED] wrote: Hi, On 3/10/08, Derk Dukker [EMAIL PROTECTED] wrote: Hi Tero, I also have a Terratec Cinergy DT XS diversity but can't get it working with the Cinergy CI usb, do you have any idea how I can make it work? By the way, they showed on CEBIT a EeePC with linux on it with the Cinergy XSS. They also said that they will release linux drivers for all of their tv tuners. This was an eeePC with a Terratec Hybrid XS FM (Analog TV, Radio, DVB-T), Pinnacle also had an eeePC with a Pinnacle 330e (Analog TV and DVB-T) both Empia em28xx based. Here's the 3liner installation instruction: http://mcentral.de/pipermail/em28xx/2008-March/001320.html Markus ___ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
