They pretty much have to. There is no way the FCC can mandate anyone to
allow any/all other licensed hams use of their station. As I said from
day one: this petition was doomed before it was written.
Joe M.
WA3GIN wrote:
Thanks for the info,
I suspect the FCC is going to frustrate
Yes I am , thanks. Chet
--- On Sat, 8/29/09, n...@no6b.com n...@no6b.com wrote:
From: n...@no6b.com n...@no6b.com
Subject: Re: [Repeater-Builder] Yaesu 5200 dual band
To: Repeater-Builder@yahoogroups.com
Date: Saturday, August 29, 2009, 12:43 AM
At 8/28/2009
I'm surprised there's not more documentation for the Spectrum
gear available on the web.
I scanned in the paperwork from some receiver and transmitter
strips I bought in 1995 and they seem to circulate around on
the web. I've even found and re-downloaded them from various
web sites when I
I also am experiencing a power-up problem with a 900 MHz Spectra. This one is
one I converted to an A9 control head and conventional operation. It's been
working fine for about the past three months or so, but now I am stuck in, for
lack of a better description, a boot loop. The radio
Hi. I have a 70cm repeater that has 2 Mastr II's, 1 for repeater, 1 for link.
Several months ago, everything worked great. I pulled it offline several
months ago and had it in my shop until a few days ago. I fired it back up, and
both receviers are dead. I can inject a 11.2 MHz signal
Did you open the preselctors?
If it is a bright tin casting you may have a tin whisker problem.
http://www.repeater-builder.com/ge/mastr2/m2casting.html
If not, I would suspect the first active device is shot.
On Sat, Aug 29, 2009 at 2:39 PM, terry dalpoaskm...@yahoo.com wrote:
Hi. I
I've got the VHF version of the SCR-500, but the manual shows the
crystal information for all the bands. I'm showing the same formula
that you have below for the UHF 406-512 receiver. My manual is dated
Edition 1, 7/87.
It specifies that the mode is 3rd overtone. Did you get a 3rd overtone
OK, let's give this a shot here. I have (tried) to install a CAT 300DXL
controller on my 7000. I programed the repeater to turn off all timers, tails,
ID's, etc. Turned the repeater button (repeat) off and turned on (remote)
button. I programmed the CAT300, EVERYTHING works except the repeated
Verify there is a jumper installed on the controller at J5 between
pins 1 and 2 if you do not have an audio delay line installed.
Also refer to:
http://www.repeater-builder.com/yaesu-vertex-standard/vxr-7000/CAT-Note-11.htm
On Sat, Aug 29, 2009 at 3:35 PM, n4zkfn4...@yahoo.com wrote:
OK,
I have the DL-1000C Audio delay board installed and had Note 11 with me at the
time. But thanks for the advise.
--- In Repeater-Builder@yahoogroups.com, DCFluX dcf...@... wrote:
Verify there is a jumper installed on the controller at J5 between
pins 1 and 2 if you do not have an audio delay
In that case make sure the COR polarity jumper on the DL-1000 is on
the right setting and that the cable between the controller and the
board is installed correctly.
Also you may try installing the jumper back on J5 if you have bad delay board.
On Sat, Aug 29, 2009 at 4:35 PM,
Well, that is possible I guess. I just got the whole controller brand new
yesterday. But I will give that a try tomorrow. Thanks,
--- In Repeater-Builder@yahoogroups.com, DCFluX dcf...@... wrote:
In that case make sure the COR polarity jumper on the DL-1000 is on
the right setting and that
Does anyone have an owners manual for the IFR FM/AM 1500 that is surplus to
their needs? I've had one for quite a while and I'm familiar with most of it's
operation but wouldn't mind having the proper manuals for it. My unit has the
digital attenuator with LCD display on it.
Would prefer not
I found some Plans on this groups page for a home made 4 pole array
http://forums.radioreference.com/antennas-coax-forum/109144-4-bay-vhf-dipole-array-project.html
scroll down a few responses and download the PDF document, I'm building one at
this time.
I just started to look at the spacings
14 matches
Mail list logo