used to
have.
Chris
N9LLO
l
(http://groups.yahoo.com/;_ylc=X3oDMTJjanNjbTc1BF9TAzk3NDc2NTkwBGdycElkAzEwNDE2OARncnBzcElkAzE3MDUwNjMxMDgEc2VjA2Z0cgRzbGsDZ2ZwBHN0aW1lAzEyNzg5MDk1OTU-
)
.
Don't assume anything
In a message dated 2/12/2010 9:07:44 P.M. Eastern Standard Time,
shield1...@yahoo.com writes:
Let me get this right...you are txing on channel 31 and rxing on Channel 1
in the CB band? You are not in the US I assume.
I use a program called slowdown and it works for me, check this link, I use
the slowint1 utility
_http://bretjohnson.us/source/source.htm_
(http://bretjohnson.us/source/source.htm)
Chris
N9LLO
In a message dated 12/25/2009 11:58:31 P.M. Eastern Standard Time,
w5jr.m...@gmail.com
Don't know where they came from but our club has one just like it on a 100w
MSF5000.
Works very well
Chris
N9LLO
In a message dated 11/25/2009 9:52:05 A.M. Eastern Standard Time,
p...@chargertech.com writes:
This set of cans has been in our club since before I was involved. None
I had to heat the lightning spike with a propane torch, there is a copper
rod soldered to a hole in it. Have someone else pulling the thing out while
you heat, after you remove the 3 screws already mentioned of course.
chris
N9LLO
In a message dated 9/9/2009 5:35:51 A.M. Eastern Daylight
Looking to convert a station with PURC control chassis to a standard
control chassis. Need backplane or complete control chassis for non-unified
(ribbon cable) Micor
Chris
N9LLO
I am interested in your antenna setup. Can you provide more details?
Chris
N9LLO
In a message dated 3/4/2009 7:35:56 P.M. Eastern Standard Time,
myto...@alltel.net writes:
One option that I like is the Syntor x9000 low band. It will do 29 to 53
Mhz, and anything in between
DTV channel numbers are relatively meaningless, it's the frequency that
counts.
Chris
N9LLO
In a message dated 2/23/2009 5:08:41 P.M. Eastern Standard Time,
wd8...@gmail.com writes:
JOHN MACKEY wrote:
If the digital is on a very different frequency, then the frequency
change
wish they would bring back the days of the licensed radio technician for land
mobile)
Chris
N9LLO
P1-18-50354
In a message dated 8/12/2008 5:08:09 P.M. Eastern Standard Time,
[EMAIL PROTECTED] writes:
I would not use them. The front end on a scanner receiver is as wide as a
double
MSR2000 that was traded in at the GE place. Best
of both worlds.
Chris
N9LLO
In a message dated 5/27/2008 3:32:57 P.M. Eastern Daylight Time,
[EMAIL PROTECTED] writes:
On May 26, 2008, at 9:56 PM, ldgelectronics wrote:
Deals like this may not be found everyday, but this one
-Builder folks want it for a scan.
Chris
N9LLO
In a message dated 5/19/2008 12:56:14 P.M. Eastern Standard Time,
[EMAIL PROTECTED] writes:
: David n1roa@ wrote:
: Well,
: I have been in touch with gamecountry.: I have been in touch w
: for $20.00 but they cannot offer nor do
In a message dated 3/13/2008 11:20:57 A.M. Eastern Standard Time,
[EMAIL PROTECTED] writes:
Maybe it is not too late to turn down the contract. Did you really think
you would be able to get them licensed to a VHF pair, or were they not totally
upfront about what they had and wanted.
at full
power,
within a given time period. That is based on the size of the heat sink.
Chris
N9LLO
**Biggest Grammy Award surprises of all time on AOL Music.
(http://music.aol.com/grammys/pictures/never-won-a-grammy?NCID=aolcmp00300025
48)
from a DB engineer back in a different time. I have one and
it
works fine.
Chris
N9LLO
**Start the year off right. Easy ways to stay in shape.
http://body.aol.com/fitness/winter-exercise?NCID=aolcmp0030002489
present on
the input will be passed right along. This results in reduced range. This is
a good way for Hams to start using their P25 radios immediately while
shopping for a Quantar. I am building one right now.
Chris
N9LLO
**See AOL's top rated recipes
In a message dated 11/15/2007 12:16:03 P.M. Eastern Standard Time,
[EMAIL PROTECTED] writes:
have finally completed construction on my 927.5250 repeater.
Where is it?
Chris
N9LLO
** See what's new at http://www.aol.com
. Greatly simplified,
thank you FCC.
Everyone here should probably take a good look at the current rules judging
by some of the replies.
That is one of the reasons these topics are not too well liked by the
admin's, everyone has their own wrong opinion of what is right.
Chris
N9LLO
the hardware.
Chris
N9LLO
** See what's new at http://www.aol.com
for a
digital transparent repeater on the ham bands. I would also like the exciter or
a complete radio would be good.
Chris
N9LLO
** See what's free at http://www.aol.com.
connector to the cap the same way. You should then be able to tune the low pass
side
notch up 25 mhz.
Chris
N9LLO
** See what's free at http://www.aol.com.
Ma-Com. The only to tell is check the flashcode. If
the
seller cant provide the flashcode
I would not consider it.
Chris
N9LLO
** See what's free at http://www.aol.com.
.
However you loose the benifit of data regeneration and error correction.
Chris
N9LLO
** See what's free at http://www.aol.com.
station.
Chris
N9LLO
** See what's free at http://www.aol.com.
In a message dated 4/15/2007 12:32:50 AM Central Daylight Time, [EMAIL
PROTECTED]
writes:
That's interesting since the FLEX cable in an HT1000 went NLA before
they even stopped making new radios! That's right - you could buy a new
radio that had one, but if it went out, you have to get one
I got one on EBAY several years ago. I think it is a 3RP1A
Chris
N9LLO
BRBRBR**BR AOL now offers free
email to everyone. Find out more about what's free from AOL at
http://www.aol.com.
You will need to change the value of the cap in parallel with the trimmer to
get it to go on freq. After that check it for excvessive temp drift. You may
still have to send the whole element in. You can also try your other elements.
Chris
N9LLO
. If your stage wont tune
after you replace the cores make sure you got the right stuff.
Chris
N9LLO
Sounds like you need to repair/replace the station control or the repeater
control board. You might need to look at the line driver also. I dont have a
manual in front of me so I am going from memory. You need the service manual
and
some test equipment.
Chris
N9LLO
In a message dated 4/30/2006 5:32:57 PM Eastern Daylight Time, [EMAIL PROTECTED] writes:
In Repeater-Builder@yahoogroups.com, [EMAIL PROTECTED] wrote: Is this in addition to lengthening the cans?Yes, I would expect that you would need a can stretcher. You get themfrom the same place as coax
This is not a Ham repeater is it? You can dial my work radio from anywhere if I give you the number!
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Looks ike a 10uf 25v to me
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
I seem to recall a band select jumper on the display boardin the 722R manual.
J2 selects UHFor VHF J3 selects repeater or base
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, sen
There is firmware replacementfor the TMX9XXX series radios to do 900 HAM. Drop a note over on the GE list.
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, send an email to:[EMAIL
The 1000 series only has one tone generator, you must use it for PL OR test tone. If you want both you must use an external tone generator for the second tone.
Chris
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from
Are you buying the crystal and soldering it in yourself? I have done many that way and about 15% of the time you have to change the capvaluein parallel with the trimmer to get it to net. This is true no matter where I get them from. The only sure bet is to send the element in.
Chris
N9LLO
cost prohibitive once you figure in shipping.
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
. The GMRS rules tell you to WRITE (not call) the FCCto see if a paticular radio is accepted for part 95. The above is pretty much the answer you will get.
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from
In a message dated 11/29/05 9:35:16 AM US Eastern Standard Time, [EMAIL PROTECTED] writes:
Is that any radio? Is there any specification as to the frequency tolerance of the transmitter mentioned? Guess I had better look it all up. I don't know why I am interested, guess it's because I have
I sent the mods for this to Kevin some time ago, they are on the Repeater-Builder site here
http://www.repeater-builder.com/db/db-4032-conversion.gif
I use one and it works fine.
Chris
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder"
The DB probucts folded dipoles are good. Good job keeping the RCA stuff on the air!
Chris (ex RCA employee)
N9LLO
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, send an email to:[EMAIL PROTECT
operational wise. I guess there are some areas of the country where things are out of hand but the primary responsibility is on the repeater owner/trustee who's
callsign is on the system. The FCC does not issure repeater licenses anymore, they are under the callsign or the owner or trustee.
Chris
N9LLO
Put me down for 1
Chris
N9LLO
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
Looking for a couple of channel elements for an RCA Tac200 UHF mobile. Also looking for a manual. This is radioabout the size of a Mastr II and the elements look similar.
Chris
N9LLO
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater
ever see one of those at a site, I will find outwhose it is and raise hell. Especially if me or my customer is havinginterference problems.-- Jim BarbourWD8CHL
They have been part 90 accepted for quite some time now.
Chris
N9LLO
Yahoo! Groups Links
To visit your group on the web, go
GMRS. All station equipment in a GMRS system must comply with the technical rules in part 95.
Notice they say to WRITE.
NEVERcall the FCC and get a rule interpretation by phone, It is legally worthless.
P.S. dont worry, be happy, run your Micor.
Chris
N9LLO
Yahoo! Groups Links
To
127.3 or 82.5 for their area.
I cant believe the IRC would tell you to move freq in this situation, this is a user problem, pretty much out of your control. I would hold my ground at least for now.
Chris
N9LLO
927.4875
444.025
53.39
Kokomo In.
444.025
Yahoo! Groups Links
To visit
46 matches
Mail list logo