Hi all
i am Golan
and i make my fuel for almost a year already.
something strange happened to me earlier today
a 100 liter batch i made last week
which passed quality test both wash test and Jan Warnqvist test
as well as aggressive stir wash -twice
turn into emulsion in the third wash
it was
?the methanol was clear and nothing at the bottom.36 hours later it was all separated i did extra 2 washes with no other problemsteal have no explanation for it
thanks anywayGolan Jim Golan Shmuel wrote: Hi all i am Golan and i make my fuel for almost a year already. something strange
On 28/08/06, Golan Shmuel [EMAIL PROTECTED] wrote:
hi andrew
i missed your respond some how sorry
any way no brown staff at the bottom
i have no explenation for it but im saspecting the viniger
im moving to the next batch
all the best
golan
hi
any explanation for passing methanol tests perfectly
but steal having third layer 3-4 mm in the wash tests
happened to me in 3 last batch's
thanks
Golan
___
Biofuel mailing list
Biofuel@sustainablelists.org
hi!
does any of you notice major difference in titration values in thesame oil before and after 1-2 months in stalling tank?
i have anew 1000 liter black staling tank outside in the sun (it get very hot here in the summer 38-45 c July Aug)
same oil that titrated 2.4 for few times before
Be careful to titrate each time you use the oil. There may be a gradient as you go down the tank. (Increasing titration#)
Best of luck.
Congratulations on the quality tests
Tom
- Original Message -
From: Golan Shmuel
To: Biofuel@sustainablelists.org
Sent: Thursday, September 21
to check methanol for water??
thanks alot
Golan
- Original Message -
From: Golan Shmuel
To: Biofuel@sustainablelists.org
Sent: Thursday, September 21, 2006 1:51 PM
Subject: [Biofuel] qulity tests help please
hi
any explanation for passing methanol tests perfectly
but steal having
of your water content. This may not be perfectly accurate but will be good enough to tell you if your methanol is contaminated. If you have a temperature close to 23 degrees you can use my data, it is here:
http://www.nonprofitfuel.ca/Reactor.htmlBest regards.Joe
Golan Shmuel wrote:
hi tom
Causes
://www.nonprofitfuel.ca/Reactor.htmlBest regards.Joe
Golan Shmuel wrote:
hi tom
Causes of soap:
1. Water in oil/chemicals used
2.Too much caustic
3. Glycerine contamination
- Is youroil dry/your chemicals pure?
- Careful titration, calculations, measurement of caustic
- Do you allow the glycerine mix to settle
hay every onei was thinking that after 500 liter good quality b.d i left the big mistakes behind me.any way the last batch i did yesterday turned out with no separation at all.it was 95 liter wvo titration
1.4.used 19 liter methanol 466g laysame reactor and reaction time (90 min) as batches
hi joe
iuse the test and it still gives me hadeake .
at list half of the times are not as it should be
im at the begining of the way and it give me direction.
i just put abigger pump and it already looking better
i alsow parchesed a PH tester and i start to take test from old BD sampels
hi mark
i use 2500 kw heating elements that being used in home boilers they are very cheap not from Cooper i don't no whats it from .have two of them in a 150 liters reactor
yet most of theprocess i use only 1 only in thebeginning when iheat the oil i use both of them to speed things up i change
.
At 20:43 05/12/2006, Golan Shmuel wrote:
HI U ALL
I HAD JUST BEEN OFFER TO USE KIND OF WONDER
MPG-CAP™ is a caplet you put into your fuel tank:This makes the fuel,
petrol or diesel, burn more efficiently, increasing the power
SAVES 15-20% FROM THE
FUEL CONSUMPTION ,CUT DOWN
13 matches
Mail list logo