Hi there, Go to the following site. http://www.linux-usb.org/SpeedTouch/suse/index.html It gives you a step by step guide to get st330 working on 10.2. It works its what I use on my OpenSuSE 10.2
Regards, Davids C. Findlay On 29/07/07, Ed Vaessen <[EMAIL PROTECTED]> wrote: > > I installed OpenSuSE 10.2 on an Athec LT51 laptop. It seems that no script > is activated to load the firmware on the Speedtouch 330 modem when it is > plugged in. > What I did was simply installing OpenSuSE 10.2 and after installation > copying the binaries speedtch-1.bin and speetch-2.bin in /lib/firmware. On > boot or on hotplugging, the modem is recognized, but after that no further > action is taken by the system. Here the output from /var/log/messages. > > Jul 7 14:10:34 AtemboPC kernel: usb 2-3: new full speed USB device using > ohci_hcd and address 3 > Jul 7 14:10:35 AtemboPC kernel: usb 2-3: new device found, idVendor=06b9, > idProduct=4061 > Jul 7 14:10:35 AtemboPC kernel: usb 2-3: new device strings: Mfr=1, > Product=2, SerialNumber=3 > Jul 7 14:10:35 AtemboPC kernel: usb 2-3: Product: Speed Touch 330 > Jul 7 14:10:35 AtemboPC kernel: usb 2-3: Manufacturer: ALCATEL > Jul 7 14:10:35 AtemboPC kernel: usb 2-3: SerialNumber: 0090D05EDE23 > Jul 7 14:10:35 AtemboPC kernel: usb 2-3: configuration #1 chosen from 1 > choice > > Normally, one might expect further messages like the following: > > Jul 7 14:10:35 AtemboPC firmware.sh[10651]: Cannot find firmware file > 'speedtch-1.bin.2.00' > Jul 7 14:10:35 AtemboPC firmware.sh[10655]: Cannot find firmware file > 'speedtch-1.bin.2' > Jul 7 14:10:35 AtemboPC kernel: speedtch 2-3:1.0: found stage 1 firmware > speedtch-1.bin > Jul 7 14:10:35 AtemboPC firmware.sh[10663]: Cannot find firmware file > 'speedtch-2.bin.2.00' > Jul 7 14:10:35 AtemboPC firmware.sh[10667]: Cannot find firmware file > 'speedtch-2.bin.2' > Jul 7 14:10:36 AtemboPC kernel: speedtch 2-3:1.0: found stage 2 firmware > speedtch-2.bin > Jul 7 14:10:40 AtemboPC kernel: ATM dev 0: ADSL line is synchronising > Jul 7 14:10:51 AtemboPC kernel: ATM dev 0: DSL line goes up > Jul 7 14:10:51 AtemboPC kernel: ATM dev 0: ADSL line is up (3072 kb/s > down | 512 kb/s up) > > > I had a look at the output of udevmonitor --env to see what happens when > the modem is plugged in and I find, among a lot of output, the line: > > PHYSDEVDRIVER=usb > > Now I also have openSuSE 10.2 installed on a desktop, where the same > speedtouch modem functions correctly and there the corresponding line > reads: > PHYSDEVDRIVER=speedtch > > Also, the module speedtch is not found on my laptop > > I am not at home with all the kernel business, so can someone please tell > what is wrong on my laptop? > > Ed > > > Liste de diffusion modem ALCATEL SpeedTouch USB > Pour se désinscrire : mailto:[EMAIL PROTECTED] > > > Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]