Carlos, So, I think the best solution here would be to send the camera to us. You could try updating the software but most likely it won't work.
Sorry for the troubles. Best regards, Oleg Dzhimiev Electronics Engineer phone: +1 801 783 5555 x124 Elphel, Inc. On 21 May 2012 18:41, Carlos Padial <palidoestud...@gmail.com> wrote: > the pc is connected over a cable to the router, and also the camera. > > in the ttylog i get no outputs when the stream stops... > > in the telnet session one time i get this message, but no longer repeats... > > Elphel353 login: root > Password: > [root@Elphel353 /root]1068# killall -9 str > [root@Elphel353 /root]1068# /usr/local/bin/str > STATE_DISCONNECT; fd == 10; revents == 25 > > After that using this command flavio suggest: > mplayer rtsp://192.168.0.9:554 -vo x11 -vf scale=480:320 > > for a while it remains with crashes (with no report) > and after that i managed to stream 1920x1088 24.995fps 136K > for several minutes the live preview works fine... then crashes and > need to restart. > > just when mplayer crashes, top is updated and all process disapear > except a few ones... > > Mem: 26048K used, 14328K free, 0K shrd, 0K buff, 14984K cached > CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq > Load average: 0.08 0.18 0.12 3/34 1151 > PID PPID USER STAT VSZ %MEM %CPU COMMAND > 831 830 root R 44928 111% 5% /usr/local/bin/str > > again, after stream live preview for two seconds at 800x608 50K > > Mem: 26216K used, 14160K free, 0K shrd, 0K buff, 15016K cached > CPU: 57% usr 7% sys 0% nic 31% idle 0% io 0% irq 3% sirq > Load average: 0.61 0.40 0.20 7/35 1281 > PID PPID USER STAT VSZ %MEM %CPU COMMAND > 770 764 root S 30936 76% 21% /usr/local/sbin/php > 771 764 root S 30936 76% 19% /usr/local/sbin/php > 836 1 root S 44928 111% 1% /usr/local/bin/str > > again > > Mem: 26064K used, 14312K free, 0K shrd, 0K buff, 15016K cached > CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq > Load average: 0.24 0.35 0.19 6/34 1281 > PID PPID USER STAT VSZ %MEM %CPU COMMAND > 839 838 root S 44928 111% 6% /usr/local/bin/str > 769 756 root R 1496 4% 0% top > 836 1 root S 44928 111% 0% /usr/local/bin/str > > again > > Mem: 26056K used, 14320K free, 0K shrd, 0K buff, 15016K cached > CPU: 0% usr 4% sys 0% nic 93% idle 0% io 0% irq 1% sirq > Load average: 0.01 0.19 0.16 2/34 1283 > PID PPID USER STAT VSZ %MEM %CPU COMMAND > 839 838 root S 44928 111% 4% /usr/local/bin/str > 712 1 root S 1136 3% 0% /bin/utelnetd -d > 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure > > sometimes after that i need to wait some minutes, and the camera > responds again, but after that i need to reboot... > > sometimes i can acces telnet when the camera crashes, i kill str and > run it again, but almost everytime it is not possible as telnet gets > freezed. > > 640x480 works always and full window works for 30-60 seconds... > > When connected directly to the pc (without router), stream least a > little more time, but no other changes... > > ??? > > > 2012/5/19 Oleg <support-list@support.elphel.com>: >> Well. I see, thanks for the logs. >> >> 1. Are your PCs connected over WiFi or cable? Try to connect one of the PCs >> over a cable - so the LAN from the camera to a PC would be wired only. >> 2. If you kill the streamer process and start it manually it will be >> displaying errors at the output. So it should report an error when mplayer >> crashes. >>> >>> killall -9 str >>> >>> /usr/local/bin/str >> >> >> Oleg > > > > -- > Carlos Padial > surreal.asturnazari.es > > _______________________________________________ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com _______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
