Could you also check the network statistics - packets/lost packets? Do you have lost packets before streaming? After?
Also, when telnet dies - and after some time comes back alive - do you have to reconnect or does it look like it hanged? Check the cables as well. On 24 May 2012 10:27, Oleg <support-list@support.elphel.com> wrote: > One more thing though. > > In the cases when you cannot telnet to the camera - > I got that the serial output doesn't display to much. Can you send > commands through the serial cable? "ifconfig", for example. > > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 5555 x124 > Elphel, Inc. > > On 24 May 2012 09:57, Oleg <support-list@support.elphel.com> wrote: >> Carlos, >> >> So, I think the best solution here would be to send the camera to us. >> You could try updating the software but most likely it won't work. >> >> Sorry for the troubles. >> >> Best regards, >> Oleg Dzhimiev >> Electronics Engineer >> phone: +1 801 783 5555 x124 >> Elphel, Inc. >> >> On 21 May 2012 18:41, Carlos Padial <palidoestud...@gmail.com> wrote: >>> the pc is connected over a cable to the router, and also the camera. >>> >>> in the ttylog i get no outputs when the stream stops... >>> >>> in the telnet session one time i get this message, but no longer repeats... >>> >>> Elphel353 login: root >>> Password: >>> [root@Elphel353 /root]1068# killall -9 str >>> [root@Elphel353 /root]1068# /usr/local/bin/str >>> STATE_DISCONNECT; fd == 10; revents == 25 >>> >>> After that using this command flavio suggest: >>> mplayer rtsp://192.168.0.9:554 -vo x11 -vf scale=480:320 >>> >>> for a while it remains with crashes (with no report) >>> and after that i managed to stream 1920x1088 24.995fps 136K >>> for several minutes the live preview works fine... then crashes and >>> need to restart. >>> >>> just when mplayer crashes, top is updated and all process disapear >>> except a few ones... >>> >>> Mem: 26048K used, 14328K free, 0K shrd, 0K buff, 14984K cached >>> CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq >>> Load average: 0.08 0.18 0.12 3/34 1151 >>> PID PPID USER STAT VSZ %MEM %CPU COMMAND >>> 831 830 root R 44928 111% 5% /usr/local/bin/str >>> >>> again, after stream live preview for two seconds at 800x608 50K >>> >>> Mem: 26216K used, 14160K free, 0K shrd, 0K buff, 15016K cached >>> CPU: 57% usr 7% sys 0% nic 31% idle 0% io 0% irq 3% sirq >>> Load average: 0.61 0.40 0.20 7/35 1281 >>> PID PPID USER STAT VSZ %MEM %CPU COMMAND >>> 770 764 root S 30936 76% 21% /usr/local/sbin/php >>> 771 764 root S 30936 76% 19% /usr/local/sbin/php >>> 836 1 root S 44928 111% 1% /usr/local/bin/str >>> >>> again >>> >>> Mem: 26064K used, 14312K free, 0K shrd, 0K buff, 15016K cached >>> CPU: 0% usr 4% sys 0% nic 92% idle 0% io 0% irq 1% sirq >>> Load average: 0.24 0.35 0.19 6/34 1281 >>> PID PPID USER STAT VSZ %MEM %CPU COMMAND >>> 839 838 root S 44928 111% 6% /usr/local/bin/str >>> 769 756 root R 1496 4% 0% top >>> 836 1 root S 44928 111% 0% /usr/local/bin/str >>> >>> again >>> >>> Mem: 26056K used, 14320K free, 0K shrd, 0K buff, 15016K cached >>> CPU: 0% usr 4% sys 0% nic 93% idle 0% io 0% irq 1% sirq >>> Load average: 0.01 0.19 0.16 2/34 1283 >>> PID PPID USER STAT VSZ %MEM %CPU COMMAND >>> 839 838 root S 44928 111% 4% /usr/local/bin/str >>> 712 1 root S 1136 3% 0% /bin/utelnetd -d >>> 751 1 root S 4136 10% 0% /usr/local/sbin/autoexposure >>> >>> sometimes after that i need to wait some minutes, and the camera >>> responds again, but after that i need to reboot... >>> >>> sometimes i can acces telnet when the camera crashes, i kill str and >>> run it again, but almost everytime it is not possible as telnet gets >>> freezed. >>> >>> 640x480 works always and full window works for 30-60 seconds... >>> >>> When connected directly to the pc (without router), stream least a >>> little more time, but no other changes... >>> >>> ??? >>> >>> >>> 2012/5/19 Oleg <support-list@support.elphel.com>: >>>> Well. I see, thanks for the logs. >>>> >>>> 1. Are your PCs connected over WiFi or cable? Try to connect one of the PCs >>>> over a cable - so the LAN from the camera to a PC would be wired only. >>>> 2. If you kill the streamer process and start it manually it will be >>>> displaying errors at the output. So it should report an error when mplayer >>>> crashes. >>>>> >>>>> killall -9 str >>>>> >>>>> /usr/local/bin/str >>>> >>>> >>>> Oleg >>> >>> >>> >>> -- >>> Carlos Padial >>> surreal.asturnazari.es >>> >>> _______________________________________________ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com _______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
