Hi Linden, You need a program like minicom to display a serial port output. The speed settings for the serial port are 115200 8N1 <https://wiki.elphel.com/wiki/Elphel_353_series_quick_start_guide#Serial_port_.2810369_board_required.29>. And the device is normally: /dev/ttyUSB0
Do you have the cable? It consists of 3 parts: parts 1 & 2, part 3 <https://wiki.elphel.com/wiki/File:Rs232-usb.jpeg>): parts 1&2: > RS-232 Adapter/Cable is used to connect to the serial port of NC353L-369 > cameras. This port outputs all the boot and debug messages and provides > system console that can be used for software development - this console > allows to control the camera even if the network is misconfigured. > This kit consists of 2 parts: 0353-01-04 - DB9 to modular adapter with > custom wiring and a > 0353-01-05 - 6-wire modular cable with crossover wiring (6-wire modular > telephone cable) part3: > USB to RS-232 converter cable - an addition to RS-232 Adapter/Cable that > allows to use a host PC's USB port instead of RS232. Regards, Oleg On Tue, Sep 10, 2019 at 5:01 PM Linden @ Zone4 <lin...@zone4.ca> wrote: > Hi Oleg, > > I have another camera with issues booting that I would like to diagnose. > Discovered I have a 10369 board can you pass along some instructions and I > will see if it has a bad block. > > Thanks, > > Linden Mills-Connery > Zone4 Team <https://zone4.ca/contact/> > 205-820 Main Street > Canmore, AB, T1W2B7 > 403-401-7215 > > > On Tue, 28 Aug 2018 at 16:19, Oleg <support-list@support.elphel.com> > wrote: > >> Linden, >> >> I reflashed the 000E64081CA1 - and it works now. >> >> It had a bad block. See the old bootlog from the serial output (via the >> extension board 10369) below. >> >> Have you ever reflashed a camera? One of the tests that can tell if the >> flash is probably corrupted is putting the camera in the netboot mode. Then >> reflash if possible - during reflashing it detects and skips the bad blocks. >> >> Boot log: >> >>> ETRAX FS NAND boot loader >>> >>> >>> >>> ========================= >>> >>> >>> >>> Rev 1, Nov 23 2009 12:31:43 >>> >>> >>> >>> Boot config: 0x00040000->0x40440000, len 0x00200000, boot @ 0x40440000 >>> >>> >>> >>> CPU revision: 0x00000020 >>> >>> >>> >>> Bootloader main at 0x38000ce2 >>> >>> >>> >>> Data end: 0x3800573c >>> >>> >>> >>> Bss: 0x38008000 >>> >>> >>> >>> Heap: 0x38008000 >>> >>> >>> >>> Identifying nand chip... >>> >>> >>> >>> maf_id: 0x0000002c; dev_id: 0x000000f1 >>> >>> >>> >>> mtd->size == 0x08000000 >>> >>> >>> >>> scan_bbt(); mtd->size == 0x08000000 >>> >>> >>> >>> scan_bbt() ...01; mtd->size == 0x08000000 >>> >>> >>> >>> len == 0x00000100; and BBT_LEN_1 == 0x00000400 >>> >>> >>> >>> scan_bbt() ...02; mtd->size == 0x08000000 >>> >>> >>> >>> scan_bbt() ...03; mtd->size == 0x08000000 >>> >>> >>> >>> scan_bbt() ...1; mtd->size == 0x08000000 >>> >>> >>> >>> scan_bbt() ...2; mtd->size == 0x08000000 >>> >>> >>> >>> scan_bbt() search_read_bbts(); mtd->size == 0x08000000 >>> >>> >>> >>> search_read_bbts() search primary table; mtd->size == 0x08000000 >>> >>> >>> >>> search_bbt() ...1; mtd->size == 0x08000000 >>> >>> >>> >>> search_bbt() ...2; maxblocks: 0x00000004; mtd->size == 0x08000000 >>> >>> >>> >>> Block: 0x000003ff >>> >>> >>> >>> Check, if we found a bbt for each requested chip >>> >>> >>> >>> Bad block table found at page0x0000ffc0, version 0x00000001 >>> >>> >>> >>> search_read_bbts() search mirror table >>> >>> >>> >>> search_bbt() ...1; mtd->size == 0x08000000 >>> >>> >>> >>> search_bbt() ...2; maxblocks: 0x00000004; mtd->size == 0x08000000 >>> >>> >>> >>> Block: 0x000003ff >>> >>> >>> >>> Block: 0x000003fe >>> >>> >>> >>> Check, if we found a bbt for each requested chip >>> >>> >>> >>> Bad block table found at page0x0000ff80, version 0x00000001 >>> >>> >>> >>> scan_bbt() ...3 >>> >>> >>> >>> Done. >>> >>> >>> >>> Chip identified... 3; NAND 128MiB 3,3V 8-bit >>> >>> >>> >>> type: 0x00000004 >>> >>> >>> >>> flags: 0x000000c5 >>> >>> >>> >>> size: 0x08000000 >>> >>> >>> >>> erasesize: 0x00020000 >>> >>> >>> >>> oobblock: 0x00000800 >>> >>> >>> >>> oobsize: 0x00000040 >>> >>> >>> >>> ecctype: 0x00000002 >>> >>> >>> >>> eccsize: 0x00000100 >>> >>> >>> >>> Oob info: >>> >>> >>> >>> useecc: 0x00000002 >>> >>> >>> >>> eccbytes: 0x00000018 >>> >>> >>> >>> eccpos: 0x00000028 0x00000029 0x0000002a 0x0000002b 0x0000002c >>> 0x0000002d 0x0000002e 0x0000002f 0x00000030 0x00000031 0x00000032 >>> 0x00000033 0x00000034 0x00000035 0x00000036 0x00000037 0x00000038 >>> 0x00000039 0x0000003a 0x0000003b 0x0000003c 0x0000003d 0x0000003e 0x0000003 >>> >>> Bootload in progress... >>> >>> >>> >>> New block 0x00040000;len: 0x00200000;start: 0x00040000 >>> >>> >>> >>> New block 0x00060000;len: 0x001e0000;start: 0x00060000 >>> >>> >>> >>> New block 0x00080000;len: 0x001c0000;start: 0x00080000 >>> >>> >>> >>> New block 0x000a0000;len: 0x001a0000;start: 0x000a0000 >>> >>> >>> >>> New block 0x000c0000;len: 0x00180000;start: 0x000c0000 >>> >>> >>> >>> New block 0x000e0000;len: 0x00160000;start: 0x000e0000 >>> >>> >>> >>> New block 0x00100000;len: 0x00140000;start: 0x00100000 >>> >>> >>> >>> New block 0x00120000;len: 0x00120000;start: 0x00120000 >>> >>> >>> >>> New block 0x00140000;len: 0x00100000;start: 0x00140000 >>> >>> >>> >>> New block 0x00160000;len: 0x000e0000;start: 0x00160000 >>> >>> >>> >>> New block 0x00180000;len: 0x000c0000;start: 0x00180000 >>> >>> >>> >>> complete, status 0xffffffb6, loaded 0x00140000 bytes >>> >>> >>> >>> Data in DRAM: >>> >>> >>> >>> 0x25f005b0 0x009cedff 0xbeef05b0 >>> >>> >>> >> >> >>> >>> >>> >>> >>> >>> >>> Corrupt data in NAND flash. >>> >>> >>> >>> >>> >>> >>> >>> -- System halted >> >> >> On Mon, Aug 20, 2018 at 1:53 PM Linden @ Zone4 <lin...@zone4.ca> wrote: >> >>> Thanks for the tip, solved it: >>> I recall the autocampars.php file was causing issues on this camera >>> before and I probably tried to fix it by pasting in the file from source >>> into the web based terminal ( >>> http://10.23.33.9/index.php?site=phpshell.php). This converts all the >>> HTML entities (&npsp; etc...) to the wrong thing. I SCPed in the original >>> source, deleted /etc/autocampars.xml and ran /usr/html/autocampars.php >>> --init. Working again. >>> >>> I am still going to ship you the 000E64081CA1 mainboard (the one that >>> won't boot). >>> >>> Thanks, >>> >>> Linden Mills-Connery >>> Zone4 Team <https://zone4.ca/contact/> >>> 205-820 Main Street >>> Canmore, AB, T1W2B7 >>> 403-401-7215 >>> >>> On 20 August 2018 at 10:43, Oleg <support-list@support.elphel.com> >>> wrote: >>> >>>> Linden, >>>> >>>> Does the file look ok? It should have ~4k lines. >>>> >>>> http://192.168.0.9/index.php?site=admin-bin/editcgi.cgi?file=/usr/html/autocampars.php >>>> >>>> Regards, >>>> Oleg >>>> >>>> On Fri, Aug 17, 2018 at 6:57 PM Linden @ Zone4 <lin...@zone4.ca> wrote: >>>> >>>>> I have run '/usr/html/autocampars.php --init', looks like a very >>>>> similar error trace to loading >>>>> http://10.23.33.9/index.php?site=autocampars.php. Output posted at >>>>> bottom of GDoc: >>>>> >>>>> https://docs.google.com/document/d/1WfGlWGk0A7zLgAl1EptMntTKoKLJLodron0P0zYcpB4/edit?usp=sharing >>>>> >>>>> Linden Mills-Connery >>>>> Zone4 Team <https://zone4.ca/contact/> >>>>> 205-820 Main Street >>>>> <https://maps.google.com/?q=205-820+Main+Street+Canmore,+AB,+T1W2B7&entry=gmail&source=g> >>>>> Canmore, AB, T1W2B7 >>>>> <https://maps.google.com/?q=205-820+Main+Street+Canmore,+AB,+T1W2B7&entry=gmail&source=g> >>>>> 403-401-7215 >>>>> >>>>> On 17 August 2018 at 17:53, Oleg <support-list@support.elphel.com> >>>>> wrote: >>>>> >>>>>> I deleted /etc/autocampars.xml and went to >>>>>>> http://10.23.33.9/index.php?site=autocampars.php again to >>>>>>> re-generate it which just resulted in an error message. The error >>>>>>> message >>>>>>> is also in the GDoc. >>>>>>> >>>>>> That worked with the board I'm testing. >>>>>> >>>>>> What if you reboot? >>>>>> Try from command line? >>>>>> >>>>>> [root@Elphel353 /root]759# */usr/html/autocampars.php --init* >>>>>>> autocampars.php created a new configuration file >>>>>>> /etc/autocampars.xml from defaults. >>>>>>> Current frame=1266, sleeping to give daemons a chance >>>>>>> Current frame=1319, waking up, daemons should be dead already >>>>>>> before reset - current frame=0 >>>>>>> after reset - current frame=2 >>>>>>> setting COMPRESSOR_RUN=2 >>>>>>> setting DAEMON_EN=Array >>>>>>> ( >>>>>>> [DAEMON_EN_AUTOEXPOSURE] => 1 >>>>>>> [DAEMON_EN_STREAMER] => 1 >>>>>>> [DAEMON_EN_CCAMFTP] => 0 >>>>>>> [DAEMON_EN_CAMOGM] => 0 >>>>>>> [DAEMON_EN_TEMPERATURE] => 0 >>>>>>> [DAEMON_EN] => 3 >>>>>>> ) >>>>>>> after setParsFromPage - current frame=12 >>>>>>> Sensor was successfully initialized at August 17, 2018, 11:49 pm >>>>>>> from /etc/autocampars.xml page 0 >>>>>> >>>>>> >>>>>> Regards, >>>>>> Oleg >>>>>> >>>>>> >>>>> _______________________________________________ >>>>> Support-list mailing list >>>>> Support-list@support.elphel.com >>>>> >>>>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>>>> >>>> >>>> >>> _______________________________________________ >>> Support-list mailing list >>> Support-list@support.elphel.com >>> >>> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >>> >> >> >> -- >> Best regards, >> Oleg Dzhimiev >> Electronics Engineer >> phone: +1 801 783 5555 x124 >> Elphel, Inc. >> > _______________________________________________ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
_______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
