You say same tape, same drive,  Take drive1 offline to TSM and do
operation again which will force tape to another drive.

If I have a bad tape, I try a MOVE DATA, several times to make it 
use different drives and I can generally get all data off of it after a few tries.

David Longo

>>> [EMAIL PROTECTED] 06/12/03 04:10AM >>>
Hi

I've got the following problem.
The following shows up in the activity log:

ANR8944E Hardware or media error on drive DRIVE1          
                       (mt2.0.0.2) (OP=LOCATE, Error Number=23, CC=0, KEY=03,   
                       ASC=14, ASCQ=00, SENSE=70.00.03.00.00.00.00.1C.00.00.00.-
                       00.14.00.07.00.20.84.FF.FF.00.03.20.20.20.20.20.20.20.0D-
                       .00.00.1C.A7.02.00.00.00.00.00.00.00.00.00.00.00.00.00.0-
                       0.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.-
                       00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00-
                       .00.00.00.00.00.00.00.00.00.00, Description=An           
                       undetermined error has occurred).  Refer to Appendix D in
                       the 'Messages' manual for recommended action.            
11-06-2003 07:59:14   ANR8359E Media fault detected on LTO volume 000765L1 in   
                       drive DRIVE1 (mt2.0.0.2) of library 3583LIB.             
11-06-2003 08:01:14   ANR8944E Hardware or media error on drive DRIVE1          
                       (mt2.0.0.2) (OP=LOCATE, Error Number=23, CC=0, KEY=03,   
                       ASC=14, ASCQ=00, 

And repeats itself, same drive same volume.
If this was a scratch volume then i think there is a solution for it because i've read 
something about TSM still trying to use a scratch tape with media faults because it 
cannot mark scratch tapes damaged.
Problem here is that is is a tape with data (q libv status) and i'm not sure how to 
fix this problem.

Can anyone shed some light on this?

Thanks in advance,

Klaas Talsma


--
Bell Microproducts Europe BV

This message is intended only for the use of the person(s) (\"the intended 
recipient(s)\") to whom it is addressed.  It may contain information which is 
privileged and confidential within the meaning of applicable law.  If you are not the 
intended recipient, please contact the sender as soon as possible.  The views 
expressed in this communication may not necessarily be the views held by Bell 
Microproducts Europe BV.

##############################################################
This message is for the named person's use only.  It may 
contain confidential, proprietary, or legally privileged 
information.  No confidentiality or privilege is waived or 
lost by any mistransmission.  If you receive this message 
in error, please immediately delete it and all copies of it 
from your system, destroy any hard copies of it, and notify 
the sender.  You must not, directly or indirectly, use, 
disclose, distribute, print, or copy any part of this message
if you are not the intended recipient.  Health First reserves
the right to monitor all e-mail communications through its
networks.  Any views or opinions expressed in this message
are solely those of the individual sender, except (1) where
the message states such views or opinions are on behalf of 
a particular entity;  and (2) the sender is authorized by 
the entity to give such views or opinions.
##############################################################

Reply via email to