We used ERPS with great results. Sub millisecond caliber with no precepts packet loss even for voice. But, you can't see anything past the shut down ports. We used it with planet switches. We had to manually shut down ports to test the alternate paths which in most cases didn't happen often enough.
We did have a failure because we didn't test the alternate path often enough. If there was a way to automated that it would be better. I would listen to Hinojosa this. He has been where you are going. On Wed, Jul 4, 2018, 5:55 AM Gino A. Villarini <[email protected]> wrote: > You need to look into Juniper MX series > > From: AF <[email protected]> on behalf of Carl Peterson < > [email protected]> > > > > *Gino A. Villarini* > President > Metro Office Park #18 Suite 304 Guaynabo, Puerto Rico 00968 > > Reply-To: AnimalFarm Microwave Users Group <[email protected]> > Date: Tuesday, July 3, 2018 at 4:12 PM > To: AnimalFarm Microwave Users Group <[email protected]> > Subject: Re: [AFMUG] G.8032v2 or ERPS ring with 10G wireless links > > "You also loose a great deal of bandwidth If one side is blocking an fully > modulated link and the active path is no running full rate." > > Strong reason not to use a ring in general. In this case, I have two 10G > legs. One is only 550 meters. If is is gone, then something is really > wrong and the other will be out as well since it is much longer. Good > argument for running G.8032v2 so I can put the owner on one side of the > long link with the neighbor on the other. This way the unused link will be > the long link. > > Thinking about it, another reason to do G8032v2 is at least with Calix, > all the links with ERPS need to be the same speed, ie 10g, but with G.8032v2, > at least according to the docs, You can run different interface speeds on > different legs so I could leave an older 1G Siklu on the backup path for > now. > > We would obviously run the Siklus out of band. I have existing management > networks at each of these locations, but you could just connect the > management interface on the radio to another port on the E7 and run a > management VLAN on the ring. > > We are currently running Juniper MPLS on routers (MX and M7i). Could look > at replacing the M7i routers with Juniper switches but they don't do well > outside of a data center environment IMHO. That is the path I was going > down but doing it on the E7s is much easier from a cost, power, and cooling > perspective. The E7-2 on the other hand, is designed to run in a cabinet > by the side of the road and half of them are already in place. > > On Tue, Jul 3, 2018 at 3:35 PM, Trey Scarborough <[email protected]> wrote: > >> I am not too familiar with the Calix G8032 but some of the things I could >> see being issues would be pulling management out of the ring so that you >> don't loose connectivity to the radios on the blocked port. You also loose >> a great deal of bandwidth If one side is blocking an fully modulated link >> and the active path is no running full rate. If it uses CFM/OAM for link >> monitoring you could have issues configuring this over the radio links. You >> pretty much are forced to do this or run out of band management and force >> the ports down on link failure. >> >> Personally I would look in to Juniper Nokia 7210 or ciena 3928. The >> Nokia does full MPLS ciena does MPLS-TP and would possibly be abetter >> solution. >> >> On 7/3/2018 10:49 AM, Carl Peterson wrote: >> >> >> After moving most of our network over to VPLS, I'm working on pushing 10G >> further into the network. It doesn't make a lot of sense to do this with >> routers (cost & power) and since we use a lot of Calix gear for our GPON >> and already have some of it in place it makes sense to me to just set up a >> 10G ring and hang routers off of that where we need them. A couple of the >> legs are going to be wireless 10G links for now so I'm looking for feedback >> on G.8032v2 vs ERPS rings with wireless paths. >> >> Going to be running ~20-30 Service VLANs with multiple CVLANS and 20-30 >> other single tagged VLANs over the ring (router to router, dedicated links, >> etc). The only drawback I see is the inability to do traffic engineering >> the way we an with MPLS VPLS but I'll still have that with the transport to >> the core ring. >> >> Any gotchas I should look for? Issues with wireless? benefits of one vs >> the other? >> >> >> >> >> >> >> >> -- >> AF mailing list >> [email protected] >> http://af.afmug.com/mailman/listinfo/af_af.afmug.com >> >> > > > -- > > Carl Peterson > > *PORT NETWORKS* > > 401 E Pratt St, Ste 2553 > > Baltimore, MD 21202 > > (410) 637-3707 > -- > AF mailing list > [email protected] > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list [email protected] http://af.afmug.com/mailman/listinfo/af_af.afmug.com
