Ours are connected to 24V rectifiers and work great. On Fri, Oct 26, 2018 at 6:29 PM Ken Hohhof <[email protected]> wrote:
> This would seem to imply they want 24 volts: > > https://www.streakwave.com/itemdesc.asp?ic=24V4APOW > > > > It’s possible they could also accept 48 volts, but without some assurance > that’s true, I wouldn’t risk it. > > > > > > *From:* AF <[email protected]> *On Behalf Of *SmarterBroadband > *Sent:* Friday, October 26, 2018 4:08 PM > *To:* 'AnimalFarm Microwave Users Group' <[email protected]> > *Subject:* Re: [AFMUG] Powering Mikrotik CCR from DC > > > > We already have 1016 and 1032 at all our sites. Therefore I would like > to use them. +48v would be great!!!! > > > > *From:* AF [mailto:[email protected] <[email protected]>] *On > Behalf Of *Mathew Howard > *Sent:* Friday, October 26, 2018 1:22 PM > *To:* AFMUG <[email protected]> > *Subject:* Re: [AFMUG] Powering Mikrotik CCR from DC > > > > I'm pretty sure the 4011 doesn't have an internal power supply. I think > it's just got a normal AC adapter, like 2011 and 3011. it'll also take > 12-57v (same as the 1100AHx4, I think). > > > > There's at least one model of CCR (a 1009, I don't know if they ever did > that with anything bigger) that's made for DC and doesn't have an internal > power supply. > > > > On Fri, Oct 26, 2018 at 2:47 PM Ken Hohhof <[email protected]> wrote: > > If you’re willing to downsize a bit from the CCR, the 1100AHx4 has a 48VDC > terminal block on the back in addition to 2 AC power supplies. It has > switch chips though, each Ethernet port isn’t connected directly to the > CPU, so there are some 2.5 Gbps bottlenecks, plus it has less total CPU > horsepower. It also seems a shame to waste the AC power supplies. Makes > it easy to power them up on the bench though. The soon-to-be-available > 4011 has the same CPU but AFAIK doesn’t have a DC power input except maybe > for POE. > > > > > > *From:* AF <[email protected]> *On Behalf Of *Adam Moffett > *Sent:* Friday, October 26, 2018 2:23 PM > *To:* [email protected] > *Subject:* Re: [AFMUG] Powering Mikrotik CCR from DC > > > > Yes I've done that many times. > I don't know what their acceptable range is, so I use a regulated DC-DC > converter to give it exactly 24V. I've used Meanwell and Traco coverters. > > I drill a hole in the back of the CCR case and feed a heavy jacketed 16/2 > through it and secure it with a zip tie on the inside of the case. There > are two tiny holes near the corner that are just right to feed a little zip > tie through....I'm not sure what their actual purpose is, but they are > perfect to secure the DC cable. > > The polarity is not marked on the motherboard, so I always verify the > polarity of the existing power wire and mark a + on the white plug with a > sharpie. I leave the AC brick in their with the DC side cut off and taped > up. My thinking is that if I had to I could reconnect the AC brick. > > -Adam > > On 10/26/2018 3:04 PM, SmarterBroadband wrote: > > Is anyone powering Mikrotik CCR routers from DC. It looks like if you > pull the included AC PSU it feeds the Tik with 24volt DC. So can we just > remove the supply and feed the tik from a 24v DC supply? Anyone doing > this? Anyone know what the make / model of plug on the PSU? > > > > > > -- > AF mailing list > [email protected] > http://af.afmug.com/mailman/listinfo/af_af.afmug.com > > -- > AF mailing list > [email protected] > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list [email protected] http://af.afmug.com/mailman/listinfo/af_af.afmug.com
