I used to manufacture scada systems back in 1990. I used modules for everything. https://www.analog.com/en/products/landing-pages/001/7b/7b-series-overview.html Sure made it easy to answer “yes, we can do that”. There were the analog in and out modules and much cheaper digital modules.
Nice little sockets that you pressed into plated holes and soldered into the PCB along with a PEM nut for securing the module. Was a nice product back in the day. From: Bill Prince Sent: Wednesday, November 28, 2018 7:45 AM To: [email protected] Subject: Re: [AFMUG] Solar Array Voc A voltage divider is always an option. It just requires knowing the conversion for the particular site. bp <part15sbs{at}gmail{dot}com> On 11/27/2018 9:28 PM, Forrest Christian (List Account) wrote: Let me see if I can re-phrase my question: I'm redesigning a voltage input circuit for one of the sitemonitor products - this is for voltage metering, not for powering the device. One of the common questions I get asked is 'can I monitor my solar array voltage'. Currently the answer is usually 'probably not, unless you are certain the Voc is below 60V, and that one side of the array is already grounded to common (often isn't for mppt controllers)'. I'd rather be able to say something like 'sure, as long as the Voc isn't over X volts', where X is high enough that it contains a reasonable subset of the arrays out there. I don't think supporting 150V arrays is in the cards (and yes, I know the tristar MMPT goes up to 150V), since that starts getting in the range where clearances get hard to do on the circuit board. So I guess the question should be: What voltage would be able to measure most of the array voltages out there? On Tue, Nov 27, 2018 at 7:07 PM Robert <[email protected]> wrote: Morningstar makes one of the better charge controllers and the one that I like has ethernet access built in. It takes up to 150 V from the arrays. They also have their new Mega Controller that will do up to 600 Volts I don't know of any WISPs that are using it. We have sites that we have 2x Morningstars feeding our battery sets... Robert On 11/27/18 5:07 PM, Forrest Christian (List Account) wrote: > Looking at determining the maximum reasonable voltage range for a new > product I'm working on. > > I'm wanting to include a reasonable input for measuring solar panel > voltage (a common request). For those who are running solar arrays to > charge a DC site (not grid-connected), I'm wondering what type of array > voltages you're running. I'd prefer the Voc figure since that is worst > case, but even the nameplate voltage (i.e. multiples of 12V) would be > useful since I can kinda infer the Voc from that. > > I suspect some of you are running rather high voltages (>100Voc) on your > arrays, not sure If I'm going to be able to measure that high, but would > like to get a feel for what the reality is. > > -- > *Forrest Christian* /CEO//, PacketFlux Technologies, Inc./ > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > [email protected] <mailto:[email protected]> | > http://www.packetflux.com <http://www.packetflux.com/> > <http://www.linkedin.com/in/fwchristian> > <http://facebook.com/packetflux> <http://twitter.com/@packetflux> > > > > -- AF mailing list [email protected] http://af.afmug.com/mailman/listinfo/af_af.afmug.com -- Forrest Christian CEO, PacketFlux Technologies, Inc. Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 [email protected] | http://www.packetflux.com -------------------------------------------------------------------------------- -- AF mailing list [email protected] http://af.afmug.com/mailman/listinfo/af_af.afmug.com
-- AF mailing list [email protected] http://af.afmug.com/mailman/listinfo/af_af.afmug.com
