I have an old SAF Lumina 18ghz that is single copper only. Before I knew better.
Part of me wants to open it up and wire up the SFP with a fancy ODC so I have a 
fiber port.



> On Apr 24, 2017, at 9:54 AM, Josh Luthman <[email protected]> wrote:
> 
> I thought it was Fiber or Fiber + Copper?  Can't remember for sure...
> 
> 
> Josh Luthman
> Office: 937-552-2340
> Direct: 937-552-2343
> 1100 Wayne St
> Suite 1337
> Troy, OH 45373
> 
> On Mon, Apr 24, 2017 at 11:13 AM, Mathew Howard <[email protected] 
> <mailto:[email protected]>> wrote:
> Only if you ordered the SAF with a fiber port... I'm not sure if there's any 
> way they can be added if you got it with copper only. I made that mistake on 
> ours... but it was a long time ago, when I didn't know any better (it also 
> doesn't even cause any issue, so I don't really care, but still... ).
> 
> On Mon, Apr 24, 2017 at 9:50 AM, Josh Luthman <[email protected] 
> <mailto:[email protected]>> wrote:
> Should have a "fiber port" with their badass connector on it.  Or an SFP.
> 
> 
> Josh Luthman
> Office: 937-552-2340 <tel:(937)%20552-2340>
> Direct: 937-552-2343 <tel:(937)%20552-2343>
> 1100 Wayne St
> Suite 1337
> Troy, OH 45373
> 
> On Mon, Apr 24, 2017 at 1:05 AM, Steve Jones <[email protected] 
> <mailto:[email protected]>> wrote:
> do i drill a hole in the saf and push the fiber in the hole and the radio 
> mites will just make it work? :-)
> <quote-if-we-had-some-eggs-we-could-have-eggs-and-ham-if-we-had-some-ham-groucho-marx-78-93-48.jpg>
> 
> 
> On Sun, Apr 23, 2017 at 11:57 PM, Josh Luthman <[email protected] 
> <mailto:[email protected]>> wrote:
> Best solution would be to do fiber IMO.  SFP right into the RB.
> 
> 
> Josh Luthman
> Office: 937-552-2340 <tel:(937)%20552-2340>
> Direct: 937-552-2343 <tel:(937)%20552-2343>
> 1100 Wayne St
> Suite 1337
> Troy, OH 45373
> 
> On Mon, Apr 24, 2017 at 12:32 AM, Steve Jones <[email protected] 
> <mailto:[email protected]>> wrote:
> thanks man
> 
> i would lock it down but i dont know whats causing it, im fearful it would 
> just dump the link all together, which is fine if im on the network, but if 
> im off network (as i found out the hard way tonite) my remote access to the 
> shop drops and all the site routers ACLs limit access to the office IP. I had 
> to VPN into a contact services customer who is on our network and then 
> connect to our office so i could flip the port back on, this, btw is also why 
> i hate having to have static routes on our OSPF network,
> 
> On Sun, Apr 23, 2017 at 11:08 PM, Adam Moffett <[email protected] 
> <mailto:[email protected]>> wrote:
> I'm 100% sure a script could do that.
> 
> :global interfacestats
> :global int "ether2"
> :set interfacestats value=[/interface ethernet monitor [find name=$int] 
> as-value]
> :if (($interfacestats->"rate")!="1000Mbps") do={/interface ethernet disable 
> [find name=$int]; :delay 3; /interface ethernet enable [find name=$int]}
> 
> That took me a strangely long time to figure out how to do because Mikrotik 
> scripts are friggin weird.   But there it is.  You could schedule that every 
> xx minutes if you wanted.
> :delay 3; might not be necessary.  I'm not sure.
> 
> On the other hand, what if you just disallow all auto-negotiation options 
> except for 1000/F ?
> 
> 
> ------ Original Message ------
> From: "Steve Jones" <[email protected] 
> <mailto:[email protected]>>
> To: "[email protected] <mailto:[email protected]>" <[email protected] <mailto:[email protected]>>
> Sent: 4/23/2017 10:59:17 PM
> Subject: [AFMUG] mikrotik port monitor script
> 
>> we have a saf 11ghz primary link interconnecting our two upstream locations, 
>> about once every 6 or 7 months the mikrotik renegotiates to 100mbps. 
>> disable/enable the port fixes it.
>> 
>> Ive never been able to reproduce it because it only happens once or twice a 
>> year.
>> 
>> Is there a script i can run on the mikrotik that monitors that specific port 
>> and flaps it if it is ever not running 1gbps?
> 
> 
> 
> 
> 
> 

Reply via email to