Hello Jean-Louis,
should i apply the path on trunk or release 3.3.3?
On 19.02.2013, at 20:58, Jean-Louis Martineau wrote:
> Hello Karsten,
>
> Can you try the attached patch?
>
>
> Jean-Louis
>
>
> On 02/18/2013 06:57 AM, Karsten Fuhrmann wrote:
>> I still can't get tapespan to work, with my single tape drive setup.
>> I added interactivity and tapescan to amanda.conf. And updated amanda to
>> version 3.3.3
>>
>> Now even when i load the right tape into the tapedrive, when i run amcheck,
>> i got the following message by email:
>>
>>
>> No acceptable volumes found
>>
>> Insert volume labeled 'cf-daily-lto8' in chg-single:tape:/dev/nsa0
>> or write the name of a new changer in '/tmp/email_input'
>> or write 'abort' in the file to abort the scan.
>>
>> if i write 'abort' into /tmp/email_input it aborts. but if i just touch
>> /tmp/email_input to tell amanda that the proper tape is inserted, i get the
>> above email again. What is going on here?
>> My shell session looks like this:
>>
>> % sudo -u amanda amcheck cf-daily-lto
>> Amanda Tape Server Host Check
>> -----------------------------
>> WARNING: holding disk /mnt/amanda-holding: only 4 GB free, using nothing
>> WARNING: Not enough free space specified in amanda.conf
>> slot 0: volume 'cf-daily-lto8'
>> slot 0: volume 'cf-daily-lto8'
>>
>> The second 'slot 0: volume 'cf-daily-lto8' comes after i touched the
>> /tmp/email_input file.
>>
>> Here are the relevant parts of my amanda.conf:
>>
>> define taperscan le_scan {
>> comment "bla"
>> plugin "lexical"
>> }
>>
>> define interactivity email {
>> comment "interactivity email"
>> plugin "email"
>> property "mailto" "[email protected]"
>> property "resend_delay" "0"
>> property "check-file" "/tmp/email_input"
>> property "check-file-delay" "10"
>> }
>> interactivity "email"
>> taperscan "le_scan"
>>
>> tpchanger "chg-single:tape:/dev/nsa0"
>>
>>
>> Please help me, this thing is killing me.
>>
>>
>> On 14.02.2013, at 18:13, Karsten Fuhrmann wrote:
>>
>>> Hi, now i added this:
>>>
>>> define taperscan oldest {
>>> comment "bla"
>>> plugin "oldest"
>>> }
>>> taperscan "oldest"
>>>
>>> into my amanda.conf. Now i got an email to change the tape. But then i am
>>> stuck, amanda does not notice the newly inserted tape, and also does not
>>> react on the file /tmp/email_input i created with touch.
>>> It just waits forever. What am i missing?
>>>
>>>
>>> On 14.02.2013, at 16:53, Jean-Louis Martineau wrote:
>>>
>>>> On 02/14/2013 10:00 AM, Karsten Fuhrmann wrote:
>>>>> Hello,
>>>>> i tried that but does not work. I dont get an email to change the tape,
>>>>> instead amanda quits with:
>>>>>
>>>>> FAILURE DUMP SUMMARY:
>>>>> datastore /tank/koh/user/./k-o lev 0 partial taper: No acceptable
>>>>> volumes found
>>>>>
>>>>> i added the following in my amanda.conf:
>>>>>
>>>>> define interactivity email {
>>>>> comment "interactivity email"
>>>>> plugin "email"
>>>>> property "mailto" "[email protected]"
>>>>> property "resend_delay" "0"
>>>>> property "check-file" "/tmp/email_input"
>>>>> property "check-file-delay" "10"
>>>>> }
>>>>> interactivity "email"
>>>>>
>>>>>
>>>> The default taperscan do not use the interactivity module, you must use
>>>> the 'oldest' or 'lexical' taperscan.
>>>> see: man amanda-taperscan
>>>>
>>>> Jean-Louis
>>>>
>>> Greetings,
>>> Karsten Fuhrmann
>>> System Administrator
>>> Rothkirch Cartoon-Film GmbH
>>> Hasenheide. 54
>>> D-10967 Berlin
>>> phone +49 30 698084-109
>>> fax +49 30 698084-29
>>> mobile +49 176 49118462
>>> skype: parceval3000
>>> AIM: [email protected]
>>> Jabber: [email protected]
>>>
>>>
>> Greetings,
>> Karsten Fuhrmann
>>
>
> <single-interactivity-r3.diff>
Greetings,
Karsten Fuhrmann
System Administrator
Rothkirch Cartoon-Film GmbH
Hasenheide. 54
D-10967 Berlin
phone +49 30 698084-109
fax +49 30 698084-29
mobile +49 176 49118462
skype: parceval3000
AIM: [email protected]
Jabber: [email protected]
