Its not assigning a trade price outside the boundaries of the bar. Its assigning it to the low of the bar, not the close. So where does lower than low come in to play? -----Original Message----- From: "progster01" <[email protected]> Date: Wed, 30 Dec 2009 18:21:07 To: <[email protected]> Subject: [amibroker] Re: Backtester is opening positions at bar *low*,not at *close*
No, he meant "lower than low" as stated. The reason is that the backtester "knows" not to assign a trade price outside the boundaries of the bar. --- In [email protected], "Potato Soup" <potatoso...@...> wrote: > > You mean with prices lower than "Close", not Low right? > -----Original Message----- > From: Tomasz Janeczko <gro...@...> > Date: Wed, 30 Dec 2009 16:48:53 > To: <[email protected]> > Subject: Re: [amibroker] Re: Backtester is opening positions at bar *low*, > not at *close* > > Hello, > > Such behaviour can only have one explanation, you > are overriding BuyPrice/ShortPrice with prices lower than Low. > It can happen for example if you are referring to previous day prices > (using Ref()) > that can easily be lower than todays. > If you can not spot the error in formula send it to support and Marcin > will tell you where > error is. > > Best regards, > Tomasz Janeczko > amibroker.com > > On 2009-12-30 13:12, Potato Soup wrote: > > > > > > I have that value set to 0% in the Portfolio tab. Has been that way > > for some tmie. I will run the test with detailed reports. Thanks. > > > > ------------------------------------------------------------------------ > > *From:* Mike <sfclimb...@...> > > *To:* [email protected] > > *Sent:* Wed, December 30, 2009 1:32:53 AM > > *Subject:* [amibroker] Re: Backtester is opening positions at bar > > *low*, not at *close* > > > > There is a setting in AA Settings that prevents taking a position if > > your volume exceeds a certain threshold of the bar's volume. If you > > were right on the cusp of that threshold with a lessor commission, > > perhaps with the greater commission (fewere units, same total price) > > you squeeked under the limit and took the trade. > > > > Best way to compare is to set AA Settings reporting to detailed, then > > run under both scenarios and compare the output. You will see why each > > signal was accepted/rejected. > > > > Mike > > > > --- In [email protected] <mailto:[email protected]>, > > Potato Soup <potatosoupz@> wrote: > > > > > > Well I have my account balance at $350k and I'm trading no more than > > $30k max in positions, how on earth could it skip a trade with that? I > > am using 2:1 margin but with that ratio of capital to exposure it > > should be impossible to have an effect. What else could be the reason? > > > > > > Also I have no changes or uses of BuyPrice/SellPrice and I have > > trade delays set to 0 for all four types of orders. > > > > > > Given all that, what other reasons could cause this behavior? > > > > > > Thanks for your help, as always. > > > > > > > > > > > > > > > ________________________________ > > > From: Mike <sfclimbers@> > > > To: [email protected] <mailto:[email protected]> > > > Sent: Tue, December 29, 2009 11:52:48 PM > > > Subject: [amibroker] Re: Backtester is opening positions at bar > > *low*, not at *close* > > > > > > 1. Changing *any* setting related to pricing can affect your trades. > > All it takes is one penny too little in your account to prevent the > > taking of a trade, which in turn would mean having more funds > > available for the next opportunities (i.e. able to take other trades) > > that would not have been there if the original trade were able to be > > taken at a penny less. > > > > > > 2. If you've confirmed that the AA Settings window has the trade > > price marked as Close, and that you have not put in an override in > > your AFL code (look for BuyPrice, SellPrice and Signal alteration in > > custom backtester code), then check too that you have not set any > > trade delays. A trade delay will cause the next bar(s) price to be > > used which will likely be different than that of the bar on which the > > signal was triggered. > > > > > > Mike > > > > > > --- In [email protected] <mailto:[email protected]>, > > Potato Soup <potatosoupz@> wrote: > > > > > > > > Now this is really weird. I just ran the backtester again and also > > noticed that the trade opening and closing is happening on the LOW of > > bars that have signals, not on the CLOSE, as I've defined it in the > > settings for the backtester. I have it set to execute trades on Close > > for all four parameters (buy,sell,short,cover). > > > > > > > > Why would this be happening? I haven't overriden it in my AFL > > either. It's completely throwing off the results of the test. > > Obviously there's no way to know what the low of a bar would be until > > the bar is complete, and in the past. > > > > > > > > > > > > > > > > > > > ------------------------------------ > > > > > > **** IMPORTANT PLEASE READ **** > > > This group is for the discussion between users only. > > > This is *NOT* technical support channel. > > > > > > TO GET TECHNICAL SUPPORT send an e-mail directly to > > > SUPPORT {at} amibroker.com <http://amibroker.com> > > > > > > TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at > > > http://www.amibroker.com/feedback/ > > > (submissions sent via other channels won't be considered) > > > > > > For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG: > > > http://www.amibroker.com/devlog/ > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > ------------------------------------ > > > > **** IMPORTANT PLEASE READ **** > > This group is for the discussion between users only. > > This is *NOT* technical support channel. > > > > TO GET TECHNICAL SUPPORT send an e-mail directly to > > SUPPORT {at} amibroker.com > > > > TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at > > http://www.amibroker.com/feedback/ > > (submissions sent via other channels won't be considered) > > > > For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG: > > http://www.amibroker.com/devlog/ > > > > Yahoo! Groups Links > > > > > > [email protected] > > <mailto:[email protected]> > > > > > > > > > > > > > ------------------------------------ **** IMPORTANT PLEASE READ **** This group is for the discussion between users only. This is *NOT* technical support channel. TO GET TECHNICAL SUPPORT send an e-mail directly to SUPPORT {at} amibroker.com TO SUBMIT SUGGESTIONS please use FEEDBACK CENTER at http://www.amibroker.com/feedback/ (submissions sent via other channels won't be considered) For NEW RELEASE ANNOUNCEMENTS and other news always check DEVLOG: http://www.amibroker.com/devlog/ Yahoo! Groups Links
