Hi All, I am trying to port gingerbread on omapevm3530 based target board using latest gingerbread source code and rowboat fyoro kernel 2.6.32. I have checked out the latest source code and built android root file system and kernel. <http://git.android-x86.org/> I am facing below kernel panic --
## Booting image at 80000000 ... Image Name: Linux-2.6.32 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2407496 Bytes = 2.3 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................................................................................... Linux version 2.6.32 (r...@celestial-laptop) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #6 Fri Dec 24 16:37:18 CST 2010 CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: OMAP3 EVM Memory policy: ECC disabled, Data cache writeback OMAP3430/3530 ES2.1 (l2cache iva sgx neon isp ) SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 Reserving 4194304 bytes SDRAM for VRAM Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk0p2 androidboot.console=ttyS0 rw ip=off devfs=mount init=/init rootdelay=3 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 120348KB available (4212K code, 824K data, 168K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:402 Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz Reprogramming SDRC clock to 332000000 Hz GPMC revision 5.0 IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller OMAP GPIO hardware version 2.5 OMAP clockevent source: GPTIMER1 at 32768 Hz Console: colour dummy device 80x30 Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok regulator: core version 0.5 NET: Registered protocol family 16 omap3evmdc: Driver registration complete OMAP DMA hardware revision 4.0 bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 regulator: VMMC1: 1850 <--> 3150 mV normal standby regulator: VDAC: 1800 mV normal standby regulator: VAUX2_4030: 1800 mV normal standby regulator: VPLL2: 1800 mV normal standby regulator: VSIM: 1800 <--> 3000 mV normal standby regulator: VUSB1V5: 1500 mV normal standby regulator: VUSB1V8: 1800 mV normal standby twl_reg twl_reg.18: can't register VUSB1V8, -16 twl_reg: probe of twl_reg.18 failed with error -16 i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz Switching to clocksource 32k_counter musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. omap-iommu omap-iommu.0: isp registered OMAP35x Linux PSP version 03.00.01.06 (OMAP3EVM) NetWinder Floating Point Emulator V0.97 (double precision) ashmem: initialized VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. msgmni has been set to 235 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OMAP DSS rev 2.0 OMAP DISPC rev 3.0 OMAP VENC rev 2 OMAP DSI rev 1.0 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 console [ttyS0] enabled serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 brd: module loaded loop: module loaded omap2-nand driver initializing OneNAND driver initializing omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, virtual base c8880000 Muxed OneNAND 128MB 1.8V 16-bit (0x30) OneNAND version = 0x0221 Scanning device for bad blocks onenand_bbt_wait: ecc error = 0x2222, controller error 0x2400 Bad eraseblock 676 at 0x05480000 Creating 5 MTD partitions on "omap2-onenand": 0x000000000000-0x000000080000 : "xloader-onenand" 0x000000080000-0x000000260000 : "uboot-onenand" 0x000000260000-0x000000280000 : "params-onenand" 0x000000280000-0x000000780000 : "linux-onenand" 0x000000780000-0x000008000000 : "jffs2-onenand" smsc911x: Driver version 2008-10-21. smsc911x-mdio: probed eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1) net eth0: MAC Address: 00:50:c2:7e:88:a4 usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver dm9601 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OMAP-EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd usb usb1: SerialNumber: ehci-omap.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbtest android init android_probe pdata: c047bac8 android_bind android_usb gadget: android_usb ready musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: MUSB HDRC host driver usb usb2: Manufacturer: Linux 2.6.32 musb-hcd usb usb2: SerialNumber: musb_hdrc hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected f_adb init android_register_function adb adb_bind_config f_mass_storage init android_register_function usb_mass_storage input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0 ads7846 spi1.0: touchscreen, irq 335 input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi1.0/input/input1 using rtc device, twl_rtc, for alarms twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 twl_rtc twl_rtc: Power up reset detected. twl_rtc twl_rtc: Enabling TWL-RTC. i2c /dev entries driver Linux video capture interface: v2.00 tvp514x 3-005d: Registered to v4l2 master omap34xxcam!! omap-iommu omap-iommu.0: isp: version 1.1 usbcore: registered new interface driver uvcvideo USB Video Class driver (v0.1.0) OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' Advanced Linux Sound Architecture Driver Version 1.0.21. usbcore: registered new interface driver snd-usb-audio No device for DAI omap-mcbsp-dai-0 No device for DAI omap-mcbsp-dai-1 No device for DAI omap-mcbsp-dai-2 No device for DAI omap-mcbsp-dai-3 No device for DAI omap-mcbsp-dai-4 OMAP3 EVM SoC init asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok ALSA device list: #0: omap3evm (twl4030) TCP cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 Power Management for TI OMAP3. Division by zero in kernel. [<c0038890>] (unwind_backtrace+0x0/0xd0) from [<c017cb5c>] (Ldiv0+0x8/0x10) Division by zero in kernel. [<c0038890>] (unwind_backtrace+0x0/0xd0) from [<c017cb5c>] (Ldiv0+0x8/0x10) SmartReflex driver initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) mmc0: new high speed SD card at address b368 mmcblk0: mmc0:b368 SD02G 1.85 GiB mmcblk0: p1 p2 tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb tvp514x 3-005d: Unable to detect decoder tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb tvp514x 3-005d: Unable to detect decoder tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb tvp514x 3-005d: Unable to detect decoder tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb tvp514x 3-005d: Unable to detect decoder omapdss DPI error: display already enabled omap_vout omap_vout: 'lcd' Display already enabled omapdss DPI error: display already enabled omap_vout omap_vout: 'lcd' Display already enabled omap_vout omap_vout: Buffer Size = 3686400 omap_vout omap_vout: : registered and initialized video device 0 omap_vout omap_vout: Buffer Size = 3686400 omap_vout omap_vout: : registered and initialized video device 1 Waiting 3sec before mounting root device... kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:2. Freeing init memory: 168K Warning: unable to open an initial console. init: cannot open '/initlogo.rle' Kernel panic - not syncing: Attempted to kill init! Any help will be highly appreciated. Thanks & Regards, Deepak -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
