First try with generic buid using make command On Fri, Dec 24, 2010 at 8:11 PM, Srinidhi K V <[email protected]>wrote:
> Hi Deepak, > > Glad that you could fix the issue. Can you please share the steps you > followed on building Ginger bread for your target. > I am trying to build Ginger bread for hawkboard, when build completes > out/target/product/hawkboard/root is empty. > I don't understand where I am missing out. > > Thanks > Srinidhi > > > On Fri, Dec 24, 2010 at 5:34 PM, deepak singal <[email protected]>wrote: > >> Done ....... >> simply comment on fs in init.rc file >> >> >> On Fri, Dec 24, 2010 at 7:00 PM, deepak singal <[email protected]>wrote: >> >>> Hi All, >>> >>> I'm facing below error msg at loglevel 6 ---- >>> >>> >>> VFS: Mounted root (ext3 filesystem) on device 179:2. >>> Freeing init memory: 168K >>> Warning: unable to open an initial console. >>> init: cannot open '/initlogo.rle' >>> init: command 'loglevel' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'export' r=0 >>> init: command 'symlink' r=0 >>> init: command 'symlink' r=0 >>> init: command 'symlink' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mount' r=-1 >>> init: command 'mkdir' r=0 >>> init: command 'symlink' r=0 >>> init: command 'mkdir' r=-17 >>> init: command 'mkdir' r=-17 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mount' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mount' r=0 >>> init: command 'write' r=0 >>> init: command 'write' r=0 >>> init: command 'write' r=0 >>> init: command 'write' r=-2 >>> init: command 'write' r=-2 >>> init: command 'write' r=0 >>> init: command 'write' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'mount' r=-1 >>> init: command 'chown' r=0 >>> init: command 'chown' r=-2 >>> init: command 'chmod' r=-2 >>> init: command 'write' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'chown' r=-2 >>> init: command 'chmod' r=-2 >>> init: command 'write' r=0 >>> init: command 'mkdir' r=0 >>> init: command 'chown' r=-2 >>> init: command 'chmod' r=-2 >>> init: command 'write' r=0 >>> init: processing action 0x27d90 (fs) >>> >>> Kernel panic - not syncing: Attempted to kill init! >>> >>> Thanks & Regards >>> Deepak >>> >>> >>> On Fri, Dec 24, 2010 at 6:54 PM, Srinidhi K V <[email protected]>wrote: >>> >>>> Hi Deepak, >>>> I has the same issue while porting Froyo on Hawkboard. I had flashed the >>>> kernel to NAND, I erased it and reflashed it to NAND and this did the >>>> trick. >>>> I am not sure it will work, but you can give a try. >>>> >>>> Thanks >>>> Srinidhi >>>> >>>> On Fri, Dec 24, 2010 at 2:17 PM, deepak singal <[email protected]>wrote: >>>> >>>>> Hi All, >>>>> >>>>> I am trying to port gingerbread on omapevm3530 based target board using >>>>> latest gingerbread source code and rowboat fyoro kernel 2.6.32. >>>>> I have checked out the latest source code and built android root file >>>>> system and kernel. >>>>> <http://git.android-x86.org/> >>>>> I am facing below kernel panic -- >>>>> >>>>> ## Booting image at 80000000 ... >>>>> Image Name: Linux-2.6.32 >>>>> Image Type: ARM Linux Kernel Image (uncompressed) >>>>> Data Size: 2407496 Bytes = 2.3 MB >>>>> Load Address: 80008000 >>>>> Entry Point: 80008000 >>>>> Verifying Checksum ... OK >>>>> OK >>>>> >>>>> Starting kernel ... >>>>> >>>>> Uncompressing >>>>> Linux..................................................................................................................................................... >>>>> Linux version 2.6.32 (r...@celestial-laptop) (gcc version 4.4.1 >>>>> (Sourcery G++ Lite 2010q1-202) ) #6 Fri Dec 24 16:37:18 CST 2010 >>>>> CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c53c7f >>>>> CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache >>>>> Machine: OMAP3 EVM >>>>> Memory policy: ECC disabled, Data cache writeback >>>>> OMAP3430/3530 ES2.1 (l2cache iva sgx neon isp ) >>>>> SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 >>>>> Reserving 4194304 bytes SDRAM for VRAM >>>>> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >>>>> 32512 >>>>> Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk0p2 >>>>> androidboot.console=ttyS0 rw ip=off devfs=mount init=/init rootdelay=3 >>>>> PID hash table entries: 512 (order: -1, 2048 bytes) >>>>> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) >>>>> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) >>>>> Memory: 128MB = 128MB total >>>>> Memory: 120348KB available (4212K code, 824K data, 168K init, 0K >>>>> highmem) >>>>> Hierarchical RCU implementation. >>>>> NR_IRQS:402 >>>>> Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz >>>>> Reprogramming SDRC clock to 332000000 Hz >>>>> GPMC revision 5.0 >>>>> IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts >>>>> Total of 96 interrupts on 1 active controller >>>>> OMAP GPIO hardware version 2.5 >>>>> OMAP clockevent source: GPTIMER1 at 32768 Hz >>>>> Console: colour dummy device 80x30 >>>>> Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) >>>>> Mount-cache hash table entries: 512 >>>>> CPU: Testing write buffer coherency: ok >>>>> regulator: core version 0.5 >>>>> NET: Registered protocol family 16 >>>>> omap3evmdc: Driver registration complete >>>>> OMAP DMA hardware revision 4.0 >>>>> bio: create slab <bio-0> at 0 >>>>> SCSI subsystem initialized >>>>> usbcore: registered new interface driver usbfs >>>>> usbcore: registered new interface driver hub >>>>> usbcore: registered new device driver usb >>>>> i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz >>>>> twl4030: PIH (irq 7) chaining IRQs 368..375 >>>>> twl4030: power (irq 373) chaining IRQs 376..383 >>>>> twl4030: gpio (irq 368) chaining IRQs 384..401 >>>>> regulator: VMMC1: 1850 <--> 3150 mV normal standby >>>>> regulator: VDAC: 1800 mV normal standby >>>>> regulator: VAUX2_4030: 1800 mV normal standby >>>>> regulator: VPLL2: 1800 mV normal standby >>>>> regulator: VSIM: 1800 <--> 3000 mV normal standby >>>>> regulator: VUSB1V5: 1500 mV normal standby >>>>> regulator: VUSB1V8: 1800 mV normal standby >>>>> twl_reg twl_reg.18: can't register VUSB1V8, -16 >>>>> twl_reg: probe of twl_reg.18 failed with error -16 >>>>> i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz >>>>> i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz >>>>> Switching to clocksource 32k_counter >>>>> musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 >>>>> musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 >>>>> NET: Registered protocol family 2 >>>>> IP route cache hash table entries: 1024 (order: 0, 4096 bytes) >>>>> TCP established hash table entries: 4096 (order: 3, 32768 bytes) >>>>> TCP bind hash table entries: 4096 (order: 2, 16384 bytes) >>>>> TCP: Hash tables configured (established 4096 bind 4096) >>>>> TCP reno registered >>>>> UDP hash table entries: 256 (order: 0, 4096 bytes) >>>>> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) >>>>> NET: Registered protocol family 1 >>>>> RPC: Registered udp transport module. >>>>> RPC: Registered tcp transport module. >>>>> RPC: Registered tcp NFSv4.1 backchannel transport module. >>>>> omap-iommu omap-iommu.0: isp registered >>>>> OMAP35x Linux PSP version 03.00.01.06 (OMAP3EVM) >>>>> NetWinder Floating Point Emulator V0.97 (double precision) >>>>> ashmem: initialized >>>>> VFS: Disk quotas dquot_6.5.2 >>>>> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >>>>> JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. >>>>> msgmni has been set to 235 >>>>> alg: No test for stdrng (krng) >>>>> io scheduler noop registered >>>>> io scheduler deadline registered >>>>> io scheduler cfq registered (default) >>>>> OMAP DSS rev 2.0 >>>>> OMAP DISPC rev 3.0 >>>>> OMAP VENC rev 2 >>>>> OMAP DSI rev 1.0 >>>>> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >>>>> serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 >>>>> console [ttyS0] enabled >>>>> serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 >>>>> serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 >>>>> brd: module loaded >>>>> loop: module loaded >>>>> omap2-nand driver initializing >>>>> OneNAND driver initializing >>>>> omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, >>>>> virtual base c8880000 >>>>> Muxed OneNAND 128MB 1.8V 16-bit (0x30) >>>>> OneNAND version = 0x0221 >>>>> Scanning device for bad blocks >>>>> onenand_bbt_wait: ecc error = 0x2222, controller error 0x2400 >>>>> Bad eraseblock 676 at 0x05480000 >>>>> Creating 5 MTD partitions on "omap2-onenand": >>>>> 0x000000000000-0x000000080000 : "xloader-onenand" >>>>> 0x000000080000-0x000000260000 : "uboot-onenand" >>>>> 0x000000260000-0x000000280000 : "params-onenand" >>>>> 0x000000280000-0x000000780000 : "linux-onenand" >>>>> 0x000000780000-0x000008000000 : "jffs2-onenand" >>>>> smsc911x: Driver version 2008-10-21. >>>>> smsc911x-mdio: probed >>>>> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, >>>>> irq=-1) >>>>> net eth0: MAC Address: 00:50:c2:7e:88:a4 >>>>> usbcore: registered new interface driver cdc_ether >>>>> usbcore: registered new interface driver dm9601 >>>>> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >>>>> ehci-omap ehci-omap.0: OMAP-EHCI Host Controller >>>>> ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 >>>>> ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 >>>>> ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 >>>>> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 >>>>> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >>>>> usb usb1: Product: OMAP-EHCI Host Controller >>>>> usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd >>>>> usb usb1: SerialNumber: ehci-omap.0 >>>>> hub 1-0:1.0: USB hub found >>>>> hub 1-0:1.0: 3 ports detected >>>>> Initializing USB Mass Storage driver... >>>>> usbcore: registered new interface driver usb-storage >>>>> USB Mass Storage support registered. >>>>> usbcore: registered new interface driver usbtest >>>>> android init >>>>> android_probe pdata: c047bac8 >>>>> android_bind >>>>> android_usb gadget: android_usb ready >>>>> musb_hdrc musb_hdrc: MUSB HDRC host driver >>>>> musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 >>>>> usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 >>>>> usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >>>>> usb usb2: Product: MUSB HDRC host driver >>>>> usb usb2: Manufacturer: Linux 2.6.32 musb-hcd >>>>> usb usb2: SerialNumber: musb_hdrc >>>>> hub 2-0:1.0: USB hub found >>>>> hub 2-0:1.0: 1 port detected >>>>> f_adb init >>>>> android_register_function adb >>>>> adb_bind_config >>>>> f_mass_storage init >>>>> android_register_function usb_mass_storage >>>>> input: TWL4030 Keypad as >>>>> /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0 >>>>> ads7846 spi1.0: touchscreen, irq 335 >>>>> input: ADS7846 Touchscreen as >>>>> /devices/platform/omap2_mcspi.1/spi1.0/input/input1 >>>>> using rtc device, twl_rtc, for alarms >>>>> twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 >>>>> twl_rtc twl_rtc: Power up reset detected. >>>>> twl_rtc twl_rtc: Enabling TWL-RTC. >>>>> i2c /dev entries driver >>>>> Linux video capture interface: v2.00 >>>>> tvp514x 3-005d: Registered to v4l2 master omap34xxcam!! >>>>> omap-iommu omap-iommu.0: isp: version 1.1 >>>>> usbcore: registered new interface driver uvcvideo >>>>> USB Video Class driver (v0.1.0) >>>>> OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec >>>>> usbcore: registered new interface driver usbhid >>>>> usbhid: USB HID core driver >>>>> logger: created 64K log 'log_main' >>>>> logger: created 256K log 'log_events' >>>>> logger: created 64K log 'log_radio' >>>>> logger: created 64K log 'log_system' >>>>> Advanced Linux Sound Architecture Driver Version 1.0.21. >>>>> usbcore: registered new interface driver snd-usb-audio >>>>> No device for DAI omap-mcbsp-dai-0 >>>>> No device for DAI omap-mcbsp-dai-1 >>>>> No device for DAI omap-mcbsp-dai-2 >>>>> No device for DAI omap-mcbsp-dai-3 >>>>> No device for DAI omap-mcbsp-dai-4 >>>>> OMAP3 EVM SoC init >>>>> asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok >>>>> ALSA device list: >>>>> #0: omap3evm (twl4030) >>>>> TCP cubic registered >>>>> NET: Registered protocol family 17 >>>>> NET: Registered protocol family 15 >>>>> Power Management for TI OMAP3. >>>>> Division by zero in kernel. >>>>> [<c0038890>] (unwind_backtrace+0x0/0xd0) from [<c017cb5c>] >>>>> (Ldiv0+0x8/0x10) >>>>> Division by zero in kernel. >>>>> [<c0038890>] (unwind_backtrace+0x0/0xd0) from [<c017cb5c>] >>>>> (Ldiv0+0x8/0x10) >>>>> SmartReflex driver initialized >>>>> VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 >>>>> twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC >>>>> (946684800) >>>>> mmc0: new high speed SD card at address b368 >>>>> mmcblk0: mmc0:b368 SD02G 1.85 GiB >>>>> mmcblk0: p1 p2 >>>>> tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb >>>>> tvp514x 3-005d: Unable to detect decoder >>>>> tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb >>>>> tvp514x 3-005d: Unable to detect decoder >>>>> tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb >>>>> tvp514x 3-005d: Unable to detect decoder >>>>> tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb >>>>> tvp514x 3-005d: Unable to detect decoder >>>>> omapdss DPI error: display already enabled >>>>> omap_vout omap_vout: 'lcd' Display already enabled >>>>> omapdss DPI error: display already enabled >>>>> omap_vout omap_vout: 'lcd' Display already enabled >>>>> omap_vout omap_vout: Buffer Size = 3686400 >>>>> omap_vout omap_vout: : registered and initialized video device 0 >>>>> omap_vout omap_vout: Buffer Size = 3686400 >>>>> omap_vout omap_vout: : registered and initialized video device 1 >>>>> Waiting 3sec before mounting root device... >>>>> kjournald starting. Commit interval 5 seconds >>>>> EXT3-fs (mmcblk0p2): using internal journal >>>>> EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode >>>>> VFS: Mounted root (ext3 filesystem) on device 179:2. >>>>> Freeing init memory: 168K >>>>> Warning: unable to open an initial console. >>>>> init: cannot open '/initlogo.rle' >>>>> Kernel panic - not syncing: Attempted to kill init! >>>>> >>>>> >>>>> Any help will be highly appreciated. >>>>> >>>>> Thanks & Regards, >>>>> Deepak >>>>> >>>>> -- >>>>> unsubscribe: >>>>> [email protected]<android-porting%[email protected]> >>>>> website: http://groups.google.com/group/android-porting >>>>> >>>> >>>> >>> >> > -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
