On Sat, 2003-05-31 at 21:34, TC wrote: > Yea looks like i have a issue with t400 spans 2 & 4 :( > I now can get 2 pretty green lights on span 1 and span 3 & > on the adit 600 on T1-1 and T1-2 ..and the 2 fxs/3fxo card are all green > So i plow'd ahead on possible shakey ground ... >
Eep... Bad card maybe? > But now i dont get any dial tone when i pick up a hand set, the adit 600 > recognizes the off hook & goes amber but * does not see it off hook > And it has registered the channels > == Parsing '/etc/asterisk/zapata.conf': Found > -- Registered channel 1, FXO Kewlstart signalling > > just curious what signaling did you need on the ports for * to be a happy > camper > with adit fxs cards > I think you may have fxs and fxo reversed. for the channels bound to the fxo-8 boards, asterisk has to be set to fxs signalling, and vice versa. asterisk needs to be told what signalling to PUT on the line, as opposed to the signalling the adits expect to GET from the line. I have 1 fxo-8 board (for the inbound pots lines) and 5 fxs-8 boards (for the phones), and asterisk has channels 1-8 fxsks and 9-24 fxoks. > >>After mucking around with it a bit, I was able to get it to sync with the > >>channel bank as the clock source for the line: > >>jsci-cbank1> show clock > >> Primary Master Transmit Clock Source: Internal > >> Secondary Transmit Clock Source: Slot A DS1 2 > So this means you have the adit suppling timing to asterisk t1 spans > so your zaptel looks like this > span=1,0,0,esf,b8zs > span=2,0,0,esf,b8zs > span=3,0,0,esf,b8zs > span=4,0,0,esf,b8zs > fxoks=1-24 No, I have: fxsks=1-8 fxoks=9-24 span=1,1,0,esf,b8zs > > > Could post the output of > print config > > from the adit 600 cli sure, here ya go: jsci-cbank1> print config ------------------------------------------------------------- -Adit 600 configuration file -Created on 01/09/1999 at 00:48:13 for antkojm1 -This file is valid for the following configuration only: - - CardType - -------- -SLOT A T1x2 SW Version: 1.5.0 -SLOT 1 FXOx8 -SLOT 2 FXSx8 -SLOT 3 FXSx8 -SLOT 4 FXSx8 -SLOT 5 FXSx8 -SLOT 6 FXSx8 -NOTES: ------------------------------------------------------------- -Turning off verification messages. set verification off -Setting local off. set local off -Disconnecting all connections. disconnect a disconnect 1 disconnect 2 disconnect 3 disconnect 4 disconnect 5 disconnect 6 -Setting IP addresses. set ethernet ip address 10.109.97.62 255.255.255.0 set ip gateway 10.109.97.1 -Setting the SNMP MIB-II System Group objects. -Setting slot a. set a:1 up set a:1 fdl none set a:1 lbo 1 set a:1 framing esf set a:1 id "asterisk-internal trunk" set a:1 linecode b8zs set a:1 loopdetect on set a:1 threshold min15 uas default set a:1 threshold min15 ses default set a:1 threshold min15 es default set a:1 threshold min15 sefs default set a:1 threshold min15 les default set a:1 threshold min15 css default set a:1 threshold min15 bes default set a:1 threshold min15 dm default set a:1 threshold min15 lcv default set a:1 threshold min15 pcv default set a:1 threshold day uas default set a:1 threshold day ses default set a:1 threshold day es default set a:1 threshold day sefs default set a:1 threshold day les default set a:1 threshold day css default set a:1 threshold day bes default set a:1 threshold day dm default set a:1 threshold day lcv default set a:1 threshold day pcv default set a:1:1-24 signal ls set a:1:1-24 type voice set a:2 down set a:2 fdl none set a:2 lbo 1 set a:2 framing esf set a:2 id "CAC DS1# A:2" set a:2 linecode b8zs set a:2 loopdetect on set a:2 threshold min15 uas default set a:2 threshold min15 ses default set a:2 threshold min15 es default set a:2 threshold min15 sefs default set a:2 threshold min15 les default set a:2 threshold min15 css default set a:2 threshold min15 bes default set a:2 threshold min15 dm default set a:2 threshold min15 lcv default set a:2 threshold min15 pcv default set a:2 threshold day uas default set a:2 threshold day ses default set a:2 threshold day es default set a:2 threshold day sefs default set a:2 threshold day les default set a:2 threshold day css default set a:2 threshold day bes default set a:2 threshold day dm default set a:2 threshold day lcv default set a:2 threshold day pcv default set a:2:1-24 signal ls set a:2:1-24 type voice -Setting slot 1. set 1:1-8 signal lscpd set 1:1-8 txgain 0 set 1:1-8 rxgain 3 -Setting slot 2. set 2:1-8 signal ls set 2:1-8 txgain 0 set 2:1-8 rxgain 0 set 2:1-8 linelength short -Setting slot 3. set 3:1-8 signal ls set 3:1-8 txgain 0 set 3:1-8 rxgain 0 set 3:1-8 linelength short -Setting slot 4. set 4:1-8 signal ls set 4:1-8 txgain -3 set 4:1-8 rxgain -6 set 4:1-8 linelength short -Setting slot 5. set 5:1-8 signal ls set 5:1-8 txgain -3 set 5:1-8 rxgain -6 set 5:1-8 linelength short -Setting slot 6. set 6:1-8 signal ls set 6:1-8 txgain -3 set 6:1-8 rxgain -6 set 6:1-8 linelength short -Setting users. add user antkojm1 add user guest set user guest level 3 -Setting network id. set id "jsci-cbank1" -Setting primary and secondary clock sources. set clock1 internal set clock2 a:2 -Making connections. connect a:1:1-8 1:1-8 connect a:1:9-16 2:1-8 connect a:1:17-24 3:1-8 connect a:2:1-8 4:1-8 connect a:2:9-16 5:1-8 connect a:2:17-24 6:1-8 -Turning verification on. set verification on jsci-cbank1> > > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
