Ah, ok, yes I was misunderstanding your config. >From the sample zaptel.conf:
# The timing parameter determines the selection of primary, secondary, and # so on sync sources. If this span should be considered a primary sync # source, then give it a value of "1". For a secondary, use "2", and so on. # To not use this as a sync source, just use "0" So using 1,1 means use span 1 as the primary sync source. 0 would mean don't use it for sync... Right? My link wouldn't come up when set to 0. On Sun, 2003-06-01 at 00:34, TC wrote: > >> But now i dont get any dial tone when i pick up a hand set, the adit 600 > >> recognizes the off hook & goes amber but * does not see it off hook > >> And it has registered the channels > >> == Parsing '/etc/asterisk/zapata.conf': Found > >> -- Registered channel 1, FXO Kewlstart signalling > >> > >I think you may have fxs and fxo reversed. \ > Nope, I think maybe there is a misunderstanding of my config > I have 3x8 port FXS Cards slots 1,2,3 and 3x8 port fxo cards slots 4-6, > what i show above is the signaling to channel 1 on the first fxs card > so i am signaling using fxo kewlstart > > >for the channels bound to > >the fxo-8 boards, asterisk has to be set to fxs signalling, and vice > >versa. asterisk needs to be told what signalling to PUT on the line, as > >opposed to the signalling the adits expect to GET from the line. > Got that right :) > >I have 1 fxo-8 board (for the inbound pots lines) and 5 fxs-8 boards (for > the > >phones), and asterisk has channels 1-8 fxsks and 9-24 fxoks. > Sure if your using span 1 from the frist t400 card in * > and you are only using the first 3 service slots on interface T1-1, > with 1 fxo, & 2 fxs card. > If you have 6 slots used then you have a possible 48 channels > on the ADIT 600, the first 24 are on interface T1-1 and rest on T1-2. > The break out is slots 1-3 are channels 1-24, and > slots 4-6 are channels 25-48. > > >>After mucking around with it a bit, I was able to get it to sync with > the > > >>channel bank as the clock source for the line: > > >>jsci-cbank1> show clock > > >> Primary Master Transmit Clock Source: Internal > > >> Secondary Transmit Clock Source: Slot A DS1 2 > > So this means you have the adit supplying timing to asterisk t1 spans > > so your zaptel looks like this > > span=1,0,0,esf,b8zs > > span=2,0,0,esf,b8zs > > span=3,0,0,esf,b8zs > > span=4,0,0,esf,b8zs > > fxoks=1-24 > > >>>>No, I have: > >>>>fxsks=1-8 > >>>>fxoks=9-24 > >>>>span=1,1,0,esf,b8zs > OK my understanding here is that > "Primary Master Transmit Clock Source: Internal" > means that the primary timing source for the channel bank is its own > internal clock therefore > asterisk should *NOT* be the Primary Timing source for this span because the > ADIT 600 > is already the Primary Timing Source from its own internal clock, so timing > on this span > as specified in zaptel.conf should not be Primary or Secondary > thus span=1,0,0,esf,b8zs *NOT* span=1,1,0,esf,b8zs > > Anyone else please pipe up here that knows this stuff cold :) > > >>>>sure, here ya go: > >>>>jsci-cbank1> print config > Thxs that quite old that version of 1.5 mine is 3.01 > hmm that config is mostly similar, > think i am gonna conclude I have a completely DOA t400 > > > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
