Hello, Iam trying to configure asterisk with a PRI E1 line. I got to a point where incoming calls on PRI is landing on asterisk and asterisk immediately starts throwing the below errors on the console. The call is dropped at this point somehow.
Dec 12 15:02:57 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Dec 12 15:02:58 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Dec 12 15:02:59 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Dec 12 15:03:00 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Dec 12 15:03:02 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Dec 12 15:03:03 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Dec 12 15:03:04 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Dec 12 15:03:04 NOTICE[5783]: chan_zap.c:7437 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 *CLI> show version Asterisk CVS-v1-0-11/08/05-01:22:43 built by [EMAIL PROTECTED] on a i686 running Linux >> /etc/zaptel.conf span=1,1,0,cas,ami ;span=1,0,0,cas,ami ; have tried this too bchan=1-15 dchan=16 bchan=17-31 >> /etc/asterisk/zapata.conf ; T110P - PRI Configuration signalling=pri_cpe ;switchtype=national ;switchtype=5ess switchtype=euroisdn callerid=asreceived group=1 context=di_mainmenu channel => 1-15,17-31 >> cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" AMI/ 1 WCT1/0/1 Clear (In use) 2 WCT1/0/2 Clear (In use) 3 WCT1/0/3 Clear (In use) 4 WCT1/0/4 Clear (In use) 5 WCT1/0/5 Clear (In use) 6 WCT1/0/6 Clear (In use) 7 WCT1/0/7 Clear (In use) 8 WCT1/0/8 Clear (In use) 9 WCT1/0/9 Clear (In use) 10 WCT1/0/10 Clear (In use) 11 WCT1/0/11 Clear (In use) 12 WCT1/0/12 Clear (In use) 13 WCT1/0/13 Clear (In use) 14 WCT1/0/14 Clear (In use) 15 WCT1/0/15 Clear (In use) 16 WCT1/0/16 HDLCFCS (In use) 17 WCT1/0/17 Clear (In use) 18 WCT1/0/18 Clear (In use) 19 WCT1/0/19 Clear (In use) 20 WCT1/0/20 Clear (In use) 21 WCT1/0/21 Clear (In use) 22 WCT1/0/22 Clear (In use) 23 WCT1/0/23 Clear (In use) 24 WCT1/0/24 Clear (In use) 25 WCT1/0/25 Clear (In use) 26 WCT1/0/26 Clear (In use) 27 WCT1/0/27 Clear (In use) 28 WCT1/0/28 Clear (In use) 29 WCT1/0/29 Clear (In use) 30 WCT1/0/30 Clear (In use) 31 WCT1/0/31 Clear (In use) >> /etc/asterisk/extensions.conf [di_mainmenu] exten => s,1,Answer ; Answer the line exten => s,2,SetVar(mloop=0) ; main menu loop count exten => s,3,SetVar(mloop=$[${mloop} + 1]) ; increment by 1 , first run exten => s,4,DigitTimeout,5 ; Set Digit Timeout to 5 seconds exten => s,5,ResponseTimeout,8 ; Set Response Timeout to 8 seconds exten => s,6,(di_welcome) exten => 1,1,Goto(di_sales,s,1) exten => 2,1,Goto(di_techsupport,s,1) exten => 3,1,Goto(di_hostingsupport,s,1) exten => 4,1,Goto(di_billing,s,1) exten => 5,1,Directory(default) exten => 9,1,Goto(operator,0,1) include => internal Iam based in India and the PRI line is from TATA indicom. The switch iam connected to is a Lucent 5ess. I have tried 5ess as the switchtype too in zapata.conf and same errors. I also get the below warning if i remove and put the PRI line into the T110p. Dec 12 14:26:30 WARNING[5783]: No D-channels available! Using Primary channel 16 as D-channel anyway! zttool shows the PRI status as ok and there are no alarms. Interrupts details are below. X server is not installed and i have disabled dma on my disk. [EMAIL PROTECTED] ~]# cat /proc/interrupts CPU0 CPU1 0: 751204 690283 IO-APIC-edge timer 1: 9 0 IO-APIC-edge i8042 8: 1 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-level acpi 14: 6203 1100 IO-APIC-edge ide0 169: 0 0 IO-APIC-level uhci_hcd 177: 682240 672161 IO-APIC-level uhci_hcd, wctdm 185: 0 0 IO-APIC-level uhci_hcd 193: 102135 1252274 IO-APIC-level wcte11xp 201: 1257747 100020 IO-APIC-level wctdm 217: 94 6793 IO-APIC-level eth0 225: 8722 0 IO-APIC-level eth1 NMI: 0 0 LOC: 1441441 1441440 ERR: 0 MIS: 0 # hdparm -v /dev/hda /dev/hda: multcount = 16 (on) IO_support = 0 (default 16-bit) unmaskirq = 1 (on) using_dma = 1 (on) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 16383/255/63, sectors = 40020664320, start = 0 Wat could cause this problem ? TIA dushyanth _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users