I suggest you use the newer chan_capi-cm (loadable from sourceforge.net). Armin
On Tue, 10 Jan 2006 [EMAIL PROTECTED] wrote: > Hi all, > I installed asterisk stable cvs 1.2 and chan_capi 0.4.0 PRE1, with one AVM > Fritz Card ISDN connected to a Telecom NT1 Plus > > I configured asterisk via AMP. > No problem in making calls. > If I try to ring the ISDN Phone Number, I don't see anything on the > asterisk Console, > I I activate the capi debug , I see the ring on the capi channel. > If the context were wrong , I anyway should see some line about this.... > > Why I cannot see anything on asterisk ,nor in the /var/log/asterisk/full ? > > here is my /etc/asterisk/capi.conf > > asteriskge03:/etc/asterisk # cat capi.conf > ; > ; CAPI config > ; > ; > > ; general section > > [general] > nationalprefix=0 > internationalprefix=00 > rxgain=0.8 > txgain=0.8 > ;ulaw=yes ;set this, if you live in u-law world instead of a-law > > ; interface sections ... > > [BRI1] ;this example interface gets name 'ISDN1' and may be any > ;name not starting with 'g' or 'contr'. > ;ntmode=yes ;if isdn card operates in nt mode, set this to yes > isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial) > ;when using NT-mode, 'DID' should be set in any case > incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any > ;defaultcid=123 ;set a default caller id to that interface for dial-out, > ;this caller id will be used when dial option 'd' is set. > ;controller=0 ;ISDN4BSD default > ;controller=7 ;ISDN4BSD USB default > controller=1 ;capi controller number to use > group=1 ;dialout group > ;prefix=0 ;set a prefix to calling number on incoming calls > softdtmf=on ;enable/disable software dtmf detection, recommended for > AVM cards > relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf > detection > accountcode= ;Asterisk accountcode to use in CDRs > context=from-pstn ;context for incoming calls > holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be > used. If > ;set to 'local' (default value), no hold is done and > Asterisk may > ;play MOH. > ;immediate=yes ;DID: immediate start of pbx with extension 's' if no > digits were > ; received on incoming call (no destination number > yet) > ;MSN: start pbx on CONNECT_IND and don't wait for > SETUP/SENDING-COMPLETE. > ; info like REDIRECTINGNUMBER may be lost, but this is > necessary for > ; drivers/pbx/telco which does not send SETUP or > SENDING-COMPLETE. > ;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression > ;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation > ;(possible values: 'no', 'yes', 'force', 'g164', 'g165') > echocancelold=yes;use facility selector 6 instead of correct 8 (necessary > for older eicon drivers) > ;echotail=64 ;echo cancel tail setting > ;bridge=yes ;native bridging (CAPI line interconnect) if available > ;callgroup=1 ;Asterisk call group > devices=2 ;number of concurrent calls on this controller > ;(2 makes sense for single BRI, 30 for PRI) > > thanks in advance, > Andrea > > Chi ricevesse questa mail per errore e' gentilmente pregato di cancellarla. > > Visitate il sito http://www.frameweb.it > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
