Re: [asterisk-users] No Dialtone

Rich Adamson Sat, 07 Oct 2006 08:37:58 -0700

If you've messed up in connecting telephone lines to the wrong module,the ringing voltage sent to a fxs module will destroy it. You would needto replace the module.



Eddie Johnson Jr wrote:

Yes, I have and I received the following:

In zapata.conf your first two channels should be fxs_ks because the first
two modules are FXO mdoules. Your last two channels should be fxo_ks because
the second two modules are FXS modules.

For the TDM400P(TDM 22) the FXS modules work with the phone.  The 3 port is
for the line.  So I unplugged it from port 3, and plugged the analog phone
in port 1, made the changes to the channels and set immediate=no, restart
the server and activated asterisk.  Nothing, my friend.

Any more suggestions,

Ed

-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Francesco
Francesconi
Sent: Friday, October 06, 2006 10:23 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] No Dialtone

Did you set immediate=no in zapata.conf?

Francesco

Eddie Johnson Jr wrote:

Hello,

I have the following setup:

1. Ubuntu Dapper Server 6.06 plus latest patches

2. Asterisk 1.2.11

3. libpri 1.2.3

4. Zaptel 1.2.8

5. Digium TDM22 (TDM400P)

6. Analog phone plugged in port 3

7. The wctdm, zaptel modules load at startup, I type asterisk as root and

it is activated.

8. I check the Channel Map and I have the following:

Channel map:

Channel 01: FXO Kewlstart (Default) (Slaves: 01)

Channel 02: FXO Kewlstart (Default) (Slaves: 02)

Channel 03: FXS Kewlstart (Default) (Slaves: 03)

Channel 04: FXS Kewlstart (Default) (Slaves: 04)

4 channels configured.

I can ssh into the server and remotely connect to the server. Great!
The card is not connected to an outside line as of yet but I have no
dialtone on the phone. I spoke with a rep. at digium and was told a
dialtone should be there.

Zaptel.conf :

loadzone=us

defaultzone=us

fxoks=1,2

fxsks=3,4

Zapata.conf:

;FXS Modules

signalling=fxo_ks

channel => 1,2

;

;FXO Modules

signalling=fxs_ks

channel => 3,4

I made sure the card is not sharing an IRQ, I checked the hard drive
and all is well.  I load zttool and get the following:

cat /proc/zaptel/*

Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1"

1 WCTDM/0/0

2 WCTDM/0/1

3 WCTDM/0/2

4 WCTDM/0/3

Any suggestions?

Ed

------------------------------------------------------------------------

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users


_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users


_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users

Re: [asterisk-users] No Dialtone

Reply via email to