What happens when you do the module load chan_dahdi.so command? -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of michael k Sent: Thursday, October 06, 2011 12:10 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] dahdi show status command not avilable in CLI
Hi, astrisks*CLI> module unload chan_dahdi.so Unable to unload resource chan_dahdi.so Command 'module unload chan_dahdi.so ' failed. Producing some other error messages !!!!! On Thu, Oct 6, 2011 at 9:17 PM, Eric Wieling <[email protected]> wrote: In the Asterisk CLI run the commands "module unload chan_dahdi.so" and "module load chan_dahdi.so". -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of michael k Sent: Thursday, October 06, 2011 11:40 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] dahdi show status command not avilable in CLI Hi, I was run the commands "dahdi_genconf" and dahdi_cfg outside the CLI as the part of x100p card installation. Before issuing this command the dahdi show status command was available. There may any issues ? Michael.k On Thu, Oct 6, 2011 at 8:59 PM, gincantalupo <[email protected]> wrote: Hi Michael, what if you reload the module chan_dahdi from within the * CLI? It should give some hints..... Giorgio On 10/06/2011 05:22 PM, michael k wrote: Hi Giorgio, Thanks for your reply. I will produce some output for your reference. # lsmod | grep dahdi dahdi_echocan_mg2 39688 1 dahdi_transcode 42372 1 wctc4xxp dahdi_voicebus 79424 2 wctdm24xxp,wcte12xp dahdi 238384 14 dahdi_echocan_mg2,xpp,dahdi_transcode,wcb4xxp,wctdm,wcfxo,wctdm24xxp,wcte11xp,wct1xxp,wcte12xp,dahdi_voicebus,wct4xxp crc_ccitt 35265 2 wctdm24xxp,dahdi # service dahdi status ### Span 1: WCFXO/0 "Wildcard X100P Board 1" (MASTER) 1 FXO FXSKS (SWEC: MG2) (battery) # dahdi_cfg -vv DAHDI Tools Version - 2.3.0 DAHDI Version: 2.3.0.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01) 1 channels to configure. Setting echocan for channel 1 to mg2 # dahdi_scan [1] active=yes alarms=OK description=Wildcard X100P Board 1 name=WCFXO/0 manufacturer=Digium devicetype=Wildcard X100P location=PCI Bus 02 Slot 02 basechan=1 totchans=1 irq=193 type=analog port=1,FXO These outputs shows that the modules are loaded correctly. Any other clues ? Michael.k On Thu, Oct 6, 2011 at 8:43 PM, gincantalupo <[email protected]> wrote: Hi Michael, if you type "dah" followed by TAB and nothing appears, it means you do not have dahdi module loaded or dahdi_cfg application not launched before starting asterisk. Giorgio On 10/06/2011 04:57 PM, michael k wrote: Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command "dahdi show status" Output of CLI : astrisks*CLI> dahdi show status No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I really not understand why this command is not avilable in CLI mode. Please help me to resolve this issue Michael.k -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
