Hi, Looks like the modules are loading properly when I do the wanrouter command, but it still fail to wancfg:
pbx ~ # lsmod Module Size Used by tulip 44064 0 pbx ~ # wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-A200-SH : SLOT=0 : BUS=4 : IRQ=9 : CPU=A : PORT=PRI : HWEC=32 : V=11 Card Cnt: A200=1 pbx ~ # lsmod Module Size Used by wanec 298520 0 wanpipe_lip 118240 0 af_wanpipe 26176 0 wanpipe 914720 0 wanpipe_syncppp 21976 1 wanpipe wanrouter 36064 5 wanec,wanpipe_lip,af_wanpipe,wanpipe,wanpipe_syncppp zaptel 190244 1 wanpipe hdlc 6424 1 zaptel ppp_generic 21020 1 zaptel slhc 6400 1 ppp_generic sdladrv 72736 2 wanpipe,wanrouter tulip 44064 0 pbx ~ # wancfg Sangoma AFT Series card update flash software (version 1.9) Get index: w1g1: No such device w1g1: Failed to create connection Thanks. On Thu, 2009-01-15 at 22:36 -0600, Darrick Hartman wrote: > Stephan Monette wrote: > > Hi, > > > > I successfully installed Astlinux 0.6.2 on a compact flash and the > > machine is booting up nicely with a Sangoma A200 card installed (with > > HWEC and 4x FXO ports). > > > > I then submit the wanrouter hwprobe command to make sure the system can > > detect my Sangoma card and it does : > > > > pbx ~ # wanrouter hwprobe > > > > ------------------------------- > > | Wanpipe Hardware Probe Info | > > ------------------------------- > > 1 . AFT-A200-SH : SLOT=0 : BUS=4 : IRQ=9 : CPU=A : PORT=PRI : HWEC=32 : > > V=11 > > > > Card Cnt: A200=1 > > > > My next step is to issue the wancfg command, but the system always > > complain about a missing device w1g1 > > > > pbx ~ # wancfg > > > > Sangoma AFT Series card update flash software (version 1.9) > > > > Get index: w1g1: No such device > > w1g1: Failed to create connection > > > > The information on the website is very simple, I should just issue the > > wancfg command from a SSH terminal session (not the console). > > > > What Am I missing? > > > > Thanks. > > > > I'll admit ignorance with respect to Sangoma hardware, but what happens > if you modprobe the appropriate module to load the device before running > wancfg? That should create the necessary device nodes via udev. Note > that I may be way off base here since I don't have a Sangoma card. I'm > sure someone else does have one and could respond with a more definitive > answer. > > Philip? I know you have one of their ADSL cards, but I'm assuming > configuration would be similar. > > Darrick > -- ** Stephan Monette Unlimitel Inc. Tel.: 613-688-6212, x221 Fax.: 613-482-1077 ------------------------------------------------------------------------------ This SF.net email is sponsored by: SourcForge Community SourceForge wants to tell your story. http://p.sf.net/sfu/sf-spreadtheword _______________________________________________ Astlinux-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to [email protected].
