Hi Cleve to be clear my hardware is a TDM400 with two FXO (Red PSTN line) daughter boards. These settings apply to this configuration. If yours is greatly different then you should investigate some more. Also, I am running in the UK so my settings have been adjusted accordingly, you may have to make further tweaks to fine tune for your locale/country. These should not affect your TDM setup though.
1. /mnt/kd/zaptel.conf. Note no comment lines allowed in this file. My FXOs are in positions 2 and 3 (1 and 4 are empty). Note fxsks is needed for FXO cards - this is not a typo. ---------------------------------------------------------------------- fxsks=2 fxsks=3 loadzone=uk defaultzone=uk 2. /mnt/kd/asterisk/zapata.conf. I'm pretty sure the group= settings are superfluous, but have not been removed from an earlier configuration. Again, we _do_ mean fxs signalling for FXO cards. The channel=>2 and channel=>3 settings relate to positions 2 and 3 on the TDM card. --------------------------------------------------------------------- ; ; Zapata telephony interface ; ; Configuration file [trunkgroups] [channels] hanguponpolarityswitch=yes cidsignalling=v23 ; Added for UK CLI detection cidstart=polarity ; Added for UK CLI detection ukcallerid = yes ; Added for UK CLI detection sendcalleridafter=2 ; Added for UK CLI detection immediate=no ; as we recieve cli info before not after first ring. context=default usecallerid=yes hidecallerid=no callwaiting=no usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echotraining=yes echocancelwhenbridged=yes rxgain=0.0 txgain=0.0 group=2 callerid="PSTN Line Two" <PSTN 1> signalling=fxs_ks context=incoming-pstn2 mailbox=779 channel=>2 group=3 callerid="PSTN Line One" <PSTN 1> signalling=fxs_ks context=incoming-pstn1 mailbox=778 channel=>3 3. /mnt/kd/rc.conf -------------------------------------- The main change you need is to uncomment : ZAPMODS="wctdm" In order that I can address the box from a putty (SSH) session I set the static IP address. It runs behind a domestic ADSL router/hub on 192.168.1.1. I therefore set the following: EXTIP="192.168.1.124" EXTNM="255.255.255.0" EXTGW="192.168.1.1" DNS="192.168.1.1" I also have setup MODOPTS as follows, but I don't think this is necessary, and in some recent versions it did not actually have any effect anyway: MODOPTS="wctdm:opermode=UK wctdm:debug=1" The only other changes I made to rc.conf - which do not affect The TDM card are : DOMAIN=mydomain.com HOSTNAME=mypbx TIMEZONE=GB regards Mart Cleveland Electronic Services wrote: > Hi Martin, > > > Thankyou for the very prompt reply, > > [When you are trying to login, which account and password are you using. > The default root password after a clean installation is "astlinux".] > > The problem was that I could not access it via putty or via https://myip > nothing happen, the only way I could get it to play was to reformat the CF > and reinstall, unmount/ oldroot/cdrom then run fdisk & genunion /dev/hda2 > and all is sweet again, I can login via putty (root/astlinux) & via > https://myip (admin/astlinux) > > [As far as your TDM card goes , have you set the ZAPMODS variable in > /mnt/kd/rc.conf ? Have you setup the configuration the card for the > (assuming you are using ZAP rather than DAHDI) in /mnt/kd/zapatel.conf > and /mnt/kd/asterisk/zapata.conf.] > > I am a bit lost here as I have not setup anything here, could you please > give me assist me what exactly I should be doing here. > > Cheers > > Cleve > > -----Original Message----- > From: Martin Rogers [mailto:fromastlinux-us...@mhr.me.uk] > Sent: Sunday, 1 March 2009 8:51 PM > To: AstLinux Users Mailing List > Subject: Re: [Astlinux-users] Astlinux 0.6.3 Some strange issues please help > > Hi Cleve > > When you are trying to login, which account and password are you using. > The default root password after a clean installation is "astlinux". > > As far as your TDM card goes , have you set the ZAPMODS variable in > /mnt/kd/rc.conf ? Have you setup the configuration the card for the > (assuming you are using ZAP rather than DAHDI) in /mnt/kd/zapatel.conf > and /mnt/kd/asterisk/zapata.conf. > > Mart > > Cleveland Electronic Services wrote: >> Hi All, >> >> >> >> I finally took the plunge and installed the net5501 img onto a 1 GB CF, >> which runs on an Alix1c board I have experience the following. >> >> >> >> When I try to run create UnionFS I with the following method. >> >> >> >> pbx ~ # fdisk /dev/hda >> >> >> >> The number of cylinders for this disk is set to 1986. >> >> There is nothing wrong with that, but this is larger than 1024, >> >> and could in certain setups cause problems with: >> >> 1) software that runs at boot time (e.g., old versions of LILO) >> >> 2) booting and partitioning software from other OSs >> >> (e.g., DOS FDISK, OS/2 FDISK) >> >> >> >> Command (m for help): n >> >> Command action >> >> e extended >> >> p primary partition (1-4) >> >> p >> >> Partition number (1-4): 2 >> >> First cylinder (261-1986, default 261): 261 >> >> Last cylinder or +size or +sizeM or +sizeK (261-1986, default 1986): +128M >> >> >> >> Command (m for help): w >> >> The partition table has been altered! >> >> >> >> Calling ioctl() to re-read partition table >> >> ************************************************************************* >> >> I get the error below and the whole system hangs nothing happens even if >> I leave it for an hour. >> >> >> >> *"fdisk: WARNING: rereading partition table failed, kernel still uses >> old table: Device or resource busy"* >> >> > **************************************************************************** > ************* >> The only way to get back in i to repower the unit, but then I cannot log >> into the unit, so I have to format the CF and start all over again. >> >> > ============================================================================ > ==================================== >> Second attempt. >> >> >> >> The only way for me to setup UnionFS is this way, I have to unmount the >> oldroot/cdrom >> >> >> >> pbx ~ # umount /oldroot/cdrom >> >> >> >> pbx ~ # fdisk /dev/hda >> >> >> >> The number of cylinders for this disk is set to 1986. >> >> There is nothing wrong with that, but this is larger than 1024, >> >> and could in certain setups cause problems with: >> >> 1) software that runs at boot time (e.g., old versions of LILO) >> >> 2) booting and partitioning software from other OSs >> >> (e.g., DOS FDISK, OS/2 FDISK) >> >> >> >> Command (m for help): n >> >> Command action >> >> e extended >> >> p primary partition (1-4) >> >> p >> >> Partition number (1-4): 2 >> >> Partition 2 is already defined, delete it before re-adding >> >> >> >> Command (m for help): d >> >> Partition number (1-4): 2 >> >> >> >> Command (m for help): n >> >> Command action >> >> e extended >> >> p primary partition (1-4) >> >> p >> >> Partition number (1-4): 2 >> >> First cylinder (261-1986, default 261): 261 >> >> Last cylinder or +size or +sizeM or +sizeK (261-1986, default 1986): >> +128M >> >> Command (m for help): w >> >> The partition table has been altered! >> >> >> >> Calling ioctl() to re-read partition table >> >> pbx ~ # genunion /dev/hda2 >> >> This script will automatically create a read/write >> >> filesystem to store your AstLinux configuration. >> >> THIS SCRIPT WILL DESTROY EVERYTHING ON /dev/hda2 >> >> >> >> ARE YOU SURE YOU WANT TO CONTINUE? >> >> >> >> Please type yes to continue >> >> Are you sure? : yes >> >> >> >> WARNING: >> >> You already have a filesystem with the label ASTURW >> >> This could confuse AstLinux when it boots. >> >> I hope you know what you are doing... >> >> Press enter to continue >> >> >> >> Creating filesystem... >> >> Filesystem Created. >> >> >> >> On new systems you can optionally use unionfs instead of they key disk. >> >> >> >> To create the appropriate file structure, type yes. >> >> >> >> If you have an existing key disk and want to migrate your key disk >> >> settings to this new unionfs partition, execute movekd /dev/hda2 after >> >> this script exits. >> >> >> >> To create a new key disk structure on your new unionfs partition, >> >> type yes followed by the Enter key. Press any other key to exit. >> >> >> >> If you are new to Astlinux, you will want to say yes. >> >> Are you sure? : yes >> >> Copying files to /dev/hda2 >> >> Please reboot now or run movekd to migrate an existing key disk to your >> unionfs partition >> >> pbx ~ # reboot >> >> > ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ > +++++++ >> This method gets it all working ok but my TDM card with 2xFXO are not >> detected, how do I get it working, as the asterisk gui does not show the >> Analog card as well. >> >> >> >> Appreciate your help >> >> >> >> Cheers >> >> >> >> >> >> *Cleve Jansen* >> >> >> >> >> ------------------------------------------------------------------------ >> >> > ---------------------------------------------------------------------------- > -- >> Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, > CA >> -OSBC tackles the biggest issue in open source: Open Sourcing the > Enterprise >> -Strategies to boost innovation and cut costs with open source > participation >> -Receive a $600 discount off the registration fee with the source code: > SFAD >> http://p.sf.net/sfu/XcvMzF8H >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Astlinux-users mailing list >> Astlinux-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/astlinux-users >> >> Donations to support AstLinux are graciously accepted via PayPal to > pay...@krisk.org. > > ---------------------------------------------------------------------------- > -- > Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA > -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise > -Strategies to boost innovation and cut costs with open source participation > -Receive a $600 discount off the registration fee with the source code: SFAD > http://p.sf.net/sfu/XcvMzF8H > _______________________________________________ > Astlinux-users mailing list > Astlinux-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > pay...@krisk.org. > > > ------------------------------------------------------------------------------ > Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA > -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise > -Strategies to boost innovation and cut costs with open source participation > -Receive a $600 discount off the registration fee with the source code: SFAD > http://p.sf.net/sfu/XcvMzF8H > _______________________________________________ > Astlinux-users mailing list > Astlinux-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > pay...@krisk.org. > ------------------------------------------------------------------------------ Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise -Strategies to boost innovation and cut costs with open source participation -Receive a $600 discount off the registration fee with the source code: SFAD http://p.sf.net/sfu/XcvMzF8H _______________________________________________ Astlinux-users mailing list Astlinux-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to pay...@krisk.org.
