Not that this affect the operation, but callerid="PSTN Line Two" <PSTN 1> should be callerid="PSTN Line Two" <PSTN 2>
That will teach me to try and change the original settings to something more intutive :-) Mart Martin Rogers wrote: > Hi Cleve > > to be clear my hardware is a TDM400 with two FXO (Red PSTN line) > daughter boards. These settings apply to this configuration. If yours > is greatly different then you should investigate some more. Also, I am > running in the UK so my settings have been adjusted accordingly, you may > have to make further tweaks to fine tune for your locale/country. These > should not affect your TDM setup though. > > > 1. /mnt/kd/zaptel.conf. Note no comment lines allowed in this file. My > FXOs are in positions 2 and 3 (1 and 4 are empty). Note fxsks is needed > for FXO cards - this is not a typo. > ---------------------------------------------------------------------- > > fxsks=2 > fxsks=3 > loadzone=uk > defaultzone=uk > > > 2. /mnt/kd/asterisk/zapata.conf. I'm pretty sure the group= settings are > superfluous, but have not been removed from an earlier configuration. > Again, we _do_ mean fxs signalling for FXO cards. The channel=>2 and > channel=>3 settings relate to positions 2 and 3 on the TDM card. > --------------------------------------------------------------------- > > ; > ; Zapata telephony interface > ; > ; Configuration file > > [trunkgroups] > > [channels] > hanguponpolarityswitch=yes > cidsignalling=v23 ; Added for UK CLI detection > cidstart=polarity ; Added for UK CLI detection > ukcallerid = yes ; Added for UK CLI detection > sendcalleridafter=2 ; Added for UK CLI detection > immediate=no ; as we recieve cli info before not after first ring. > context=default > usecallerid=yes > hidecallerid=no > callwaiting=no > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echotraining=yes > echocancelwhenbridged=yes > rxgain=0.0 > txgain=0.0 > > group=2 > callerid="PSTN Line Two" <PSTN 1> > signalling=fxs_ks > context=incoming-pstn2 > mailbox=779 > channel=>2 > > group=3 > callerid="PSTN Line One" <PSTN 1> > signalling=fxs_ks > context=incoming-pstn1 > mailbox=778 > channel=>3 > > > 3. /mnt/kd/rc.conf > -------------------------------------- > > The main change you need is to uncomment : > > ZAPMODS="wctdm" > > In order that I can address the box from a putty (SSH) session I set the > static IP address. It runs behind a domestic ADSL router/hub on > 192.168.1.1. I therefore set the following: > > EXTIP="192.168.1.124" > EXTNM="255.255.255.0" > EXTGW="192.168.1.1" > DNS="192.168.1.1" > > I also have setup MODOPTS as follows, but I don't think this is > necessary, and in some recent versions it did not actually have any > effect anyway: > > MODOPTS="wctdm:opermode=UK wctdm:debug=1" > > The only other changes I made to rc.conf - which do not affect The TDM > card are : > > DOMAIN=mydomain.com > HOSTNAME=mypbx > TIMEZONE=GB > > > regards > Mart > > > > > Cleveland Electronic Services wrote: >> Hi Martin, >> >> >> Thankyou for the very prompt reply, >> >> [When you are trying to login, which account and password are you using. >> The default root password after a clean installation is "astlinux".] >> >> The problem was that I could not access it via putty or via https://myip >> nothing happen, the only way I could get it to play was to reformat the CF >> and reinstall, unmount/ oldroot/cdrom then run fdisk & genunion /dev/hda2 >> and all is sweet again, I can login via putty (root/astlinux) & via >> https://myip (admin/astlinux) >> >> [As far as your TDM card goes , have you set the ZAPMODS variable in >> /mnt/kd/rc.conf ? Have you setup the configuration the card for the >> (assuming you are using ZAP rather than DAHDI) in /mnt/kd/zapatel.conf >> and /mnt/kd/asterisk/zapata.conf.] >> >> I am a bit lost here as I have not setup anything here, could you please >> give me assist me what exactly I should be doing here. >> >> Cheers >> >> Cleve >> >> -----Original Message----- >> From: Martin Rogers [mailto:fromastlinux-us...@mhr.me.uk] >> Sent: Sunday, 1 March 2009 8:51 PM >> To: AstLinux Users Mailing List >> Subject: Re: [Astlinux-users] Astlinux 0.6.3 Some strange issues please help >> >> Hi Cleve >> >> When you are trying to login, which account and password are you using. >> The default root password after a clean installation is "astlinux". >> >> As far as your TDM card goes , have you set the ZAPMODS variable in >> /mnt/kd/rc.conf ? Have you setup the configuration the card for the >> (assuming you are using ZAP rather than DAHDI) in /mnt/kd/zapatel.conf >> and /mnt/kd/asterisk/zapata.conf. >> >> Mart >> >> Cleveland Electronic Services wrote: >>> Hi All, >>> >>> >>> >>> I finally took the plunge and installed the net5501 img onto a 1 GB CF, >>> which runs on an Alix1c board I have experience the following. >>> >>> >>> >>> When I try to run create UnionFS I with the following method. >>> >>> >>> >>> pbx ~ # fdisk /dev/hda >>> >>> >>> >>> The number of cylinders for this disk is set to 1986. >>> >>> There is nothing wrong with that, but this is larger than 1024, >>> >>> and could in certain setups cause problems with: >>> >>> 1) software that runs at boot time (e.g., old versions of LILO) >>> >>> 2) booting and partitioning software from other OSs >>> >>> (e.g., DOS FDISK, OS/2 FDISK) >>> >>> >>> >>> Command (m for help): n >>> >>> Command action >>> >>> e extended >>> >>> p primary partition (1-4) >>> >>> p >>> >>> Partition number (1-4): 2 >>> >>> First cylinder (261-1986, default 261): 261 >>> >>> Last cylinder or +size or +sizeM or +sizeK (261-1986, default 1986): +128M >>> >>> >>> >>> Command (m for help): w >>> >>> The partition table has been altered! >>> >>> >>> >>> Calling ioctl() to re-read partition table >>> >>> ************************************************************************* >>> >>> I get the error below and the whole system hangs nothing happens even if >>> I leave it for an hour. >>> >>> >>> >>> *"fdisk: WARNING: rereading partition table failed, kernel still uses >>> old table: Device or resource busy"* >>> >>> >> **************************************************************************** >> ************* >>> The only way to get back in i to repower the unit, but then I cannot log >>> into the unit, so I have to format the CF and start all over again. >>> >>> >> ============================================================================ >> ==================================== >>> Second attempt. >>> >>> >>> >>> The only way for me to setup UnionFS is this way, I have to unmount the >>> oldroot/cdrom >>> >>> >>> >>> pbx ~ # umount /oldroot/cdrom >>> >>> >>> >>> pbx ~ # fdisk /dev/hda >>> >>> >>> >>> The number of cylinders for this disk is set to 1986. >>> >>> There is nothing wrong with that, but this is larger than 1024, >>> >>> and could in certain setups cause problems with: >>> >>> 1) software that runs at boot time (e.g., old versions of LILO) >>> >>> 2) booting and partitioning software from other OSs >>> >>> (e.g., DOS FDISK, OS/2 FDISK) >>> >>> >>> >>> Command (m for help): n >>> >>> Command action >>> >>> e extended >>> >>> p primary partition (1-4) >>> >>> p >>> >>> Partition number (1-4): 2 >>> >>> Partition 2 is already defined, delete it before re-adding >>> >>> >>> >>> Command (m for help): d >>> >>> Partition number (1-4): 2 >>> >>> >>> >>> Command (m for help): n >>> >>> Command action >>> >>> e extended >>> >>> p primary partition (1-4) >>> >>> p >>> >>> Partition number (1-4): 2 >>> >>> First cylinder (261-1986, default 261): 261 >>> >>> Last cylinder or +size or +sizeM or +sizeK (261-1986, default 1986): >>> +128M >>> >>> Command (m for help): w >>> >>> The partition table has been altered! >>> >>> >>> >>> Calling ioctl() to re-read partition table >>> >>> pbx ~ # genunion /dev/hda2 >>> >>> This script will automatically create a read/write >>> >>> filesystem to store your AstLinux configuration. >>> >>> THIS SCRIPT WILL DESTROY EVERYTHING ON /dev/hda2 >>> >>> >>> >>> ARE YOU SURE YOU WANT TO CONTINUE? >>> >>> >>> >>> Please type yes to continue >>> >>> Are you sure? : yes >>> >>> >>> >>> WARNING: >>> >>> You already have a filesystem with the label ASTURW >>> >>> This could confuse AstLinux when it boots. >>> >>> I hope you know what you are doing... >>> >>> Press enter to continue >>> >>> >>> >>> Creating filesystem... >>> >>> Filesystem Created. >>> >>> >>> >>> On new systems you can optionally use unionfs instead of they key disk. >>> >>> >>> >>> To create the appropriate file structure, type yes. >>> >>> >>> >>> If you have an existing key disk and want to migrate your key disk >>> >>> settings to this new unionfs partition, execute movekd /dev/hda2 after >>> >>> this script exits. >>> >>> >>> >>> To create a new key disk structure on your new unionfs partition, >>> >>> type yes followed by the Enter key. Press any other key to exit. >>> >>> >>> >>> If you are new to Astlinux, you will want to say yes. >>> >>> Are you sure? : yes >>> >>> Copying files to /dev/hda2 >>> >>> Please reboot now or run movekd to migrate an existing key disk to your >>> unionfs partition >>> >>> pbx ~ # reboot >>> >>> >> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ >> +++++++ >>> This method gets it all working ok but my TDM card with 2xFXO are not >>> detected, how do I get it working, as the asterisk gui does not show the >>> Analog card as well. >>> >>> >>> >>> Appreciate your help >>> >>> >>> >>> Cheers >>> >>> >>> >>> >>> >>> *Cleve Jansen* >>> >>> >>> >>> >>> ------------------------------------------------------------------------ >>> >>> >> ---------------------------------------------------------------------------- >> -- >>> Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, >> CA >>> -OSBC tackles the biggest issue in open source: Open Sourcing the >> Enterprise >>> -Strategies to boost innovation and cut costs with open source >> participation >>> -Receive a $600 discount off the registration fee with the source code: >> SFAD >>> http://p.sf.net/sfu/XcvMzF8H >>> >>> >>> ------------------------------------------------------------------------ >>> >>> _______________________________________________ >>> Astlinux-users mailing list >>> Astlinux-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/astlinux-users >>> >>> Donations to support AstLinux are graciously accepted via PayPal to >> pay...@krisk.org. >> >> ---------------------------------------------------------------------------- >> -- >> Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA >> -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise >> -Strategies to boost innovation and cut costs with open source participation >> -Receive a $600 discount off the registration fee with the source code: SFAD >> http://p.sf.net/sfu/XcvMzF8H >> _______________________________________________ >> Astlinux-users mailing list >> Astlinux-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/astlinux-users >> >> Donations to support AstLinux are graciously accepted via PayPal to >> pay...@krisk.org. >> >> >> ------------------------------------------------------------------------------ >> Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA >> -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise >> -Strategies to boost innovation and cut costs with open source participation >> -Receive a $600 discount off the registration fee with the source code: SFAD >> http://p.sf.net/sfu/XcvMzF8H >> _______________________________________________ >> Astlinux-users mailing list >> Astlinux-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/astlinux-users >> >> Donations to support AstLinux are graciously accepted via PayPal to >> pay...@krisk.org. >> > > ------------------------------------------------------------------------------ > Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA > -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise > -Strategies to boost innovation and cut costs with open source participation > -Receive a $600 discount off the registration fee with the source code: SFAD > http://p.sf.net/sfu/XcvMzF8H > _______________________________________________ > Astlinux-users mailing list > Astlinux-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > pay...@krisk.org. > ------------------------------------------------------------------------------ Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA -OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise -Strategies to boost innovation and cut costs with open source participation -Receive a $600 discount off the registration fee with the source code: SFAD http://p.sf.net/sfu/XcvMzF8H _______________________________________________ Astlinux-users mailing list Astlinux-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to pay...@krisk.org.
