I recently purchased the Net5501 / Sangoma A101u Kit from Soekris and quickly
ran into the wanpipe (Sangoma) problems that most people seem to be having. I
was unable to run wancfg due to the lack of a full Perl support. I was able to
muddle my way through a manual system configuration to connect the Sangoma
A101u to a Nortel phone system via PRI. Here are the files I added and where I
put them followed by the file content....I'm using unionfs on a flash card with
no usb key or anything of that nature ( The first disk wizard config
option,...see the docs)(astlinux-0.7.0):
/etc/wanpipe/wanpipe1.conf
#================================================
# WANPIPE1 Configuration File
#================================================
[devices]
wanpipe1 = WAN_AFT, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 14
PCIBUS = 0
FE_MEDIA = T1
FE_LCODE = B8ZS
FE_FRAME = ESF
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
ACTIVE_CH = ALL
TE_HIGHIMPEDANCE = NO
LBO = 0-110FT
FE_TXTRISTATE = NO
MTU = 1500
UDPPORT = 0
TTL = 255
IGNORE_FRONT_END = NO
TDMV_SPAN = 1
TDMV_DCHAN = 24
[w1g1]
ACTIVE_CH = ALL
TDMV_ECHO_OFF = NO
____________________--__________________________________________
/etc/dahdi/system.conf
span=1,0,0,esf,b8zs
# Configuration for T1 trunk
# channel 1-23 data channels
bchan=1-23
echocanceller=mg2,1-23
# channel 24 control
dchan=24
_________________________________________________________________
Now, in the /etc/wanpipe/wanpipe1.conf file the part that I had to modify was
obviously the PCI slot and bus since this will be different on each computer.
This may be the same on other net 5501s but i'm not sure. I found this
information from typing 'wanrouter hwprobe' at the command prompt. I also had
to add '#include chan_dahdi_custom.conf' to the bottom of the
/etc/asterisk/chan_dahdi.conf file and create the chan_dahdi_custom.conf file
in the same directory with the following content:
context=internal
switchtype=national
signalling = pri_net
group = 1,24
channel => 1-23
Obviously, this could be vastly different depending on your application. After
these files where in place restarted all the relevant services:
/etc/init.d/asterisk stop
/etc/init.d/dahdi stop
/etc/init.d/wanrouter stop
/etc/init.d/wanrouter start
/etc/init.d/dahdi start
/etc/init.d/asterisk start
wanrouter start created an interface called w1g1, dahdi started silently
(good), asterisk started. Asterisk now reports all the correct dahdi info from
the CLI etc. I hope this helps. If you have questions please let me know.
------------------------------------------------------------------------------
Download Intel® Parallel Studio Eval
Try the new software tools for yourself. Speed compiling, find bugs
proactively, and fine-tune applications for parallel performance.
See why Intel Parallel Studio got high marks during beta.
http://p.sf.net/sfu/intel-sw-dev
_______________________________________________
Astlinux-users mailing list
Astlinux-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/astlinux-users
Donations to support AstLinux are graciously accepted via PayPal to
pay...@krisk.org.
