This is mostly copied verbatim from the Linux driver.
Signed-off-by: Uwe Kleine-König <[email protected]>
---
drivers/net/phy/marvell.c | 204 +++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 201 insertions(+), 3 deletions(-)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 6bb50a3a1f4c..38b2ad31f893 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -31,6 +31,9 @@
#define MII_M1011_PHY_STATUS_RESOLVED BIT(11)
#define MII_M1011_PHY_STATUS_LINK BIT(10)
+#define MII_M1111_COPPER 0
+#define MII_M1111_FIBER 1
+
#define MII_88E1121_PHY_MSCR_PAGE 2
#define MII_88E1121_PHY_MSCR_REG 21
#define MII_88E1121_PHY_MSCR_TX_DELAY BIT(4)
@@ -45,6 +48,20 @@
#define MII_88E1540_QSGMII_CONTROL 0x0
#define MII_88E1540_QSGMII_AUTONEG_EN BIT(12)
+#define MII_88E1510_GEN_CTRL_REG_1 0x14
+#define MII_88E1510_GEN_CTRL_REG_1_MODE_MASK 0x7
+#define MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII 0x1 /* SGMII to copper */
+#define MII_88E1510_GEN_CTRL_REG_1_RESET 0x8000 /* Soft reset */
+
+#define LPA_PAUSE_FIBER 0x180
+#define LPA_PAUSE_ASYM_FIBER 0x100
+
+#define ADVERTISE_FIBER_1000HALF 0x40
+#define ADVERTISE_FIBER_1000FULL 0x20
+
+#define ADVERTISE_PAUSE_FIBER 0x180
+#define ADVERTISE_PAUSE_ASYM_FIBER 0x100
+
/*
* marvell_read_status
*
@@ -133,12 +150,24 @@ static int marvell_read_status(struct phy_device *phydev)
return 0;
}
+#define MII_88E1510_GEN_CTRL_REG_1 0x14
+
static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
{
return phydev->interface >= PHY_INTERFACE_MODE_RGMII &&
phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
};
+/*
+ * This same function in the Linux kernel parses the marvell,reg-init dt
+ * property and does the necessary register writes. It's kept as an exercise
for
+ * a future user to implement this. :-)
+ */
+static int marvell_of_reg_init(struct phy_device *phydev)
+{
+ return 0;
+}
+
static int m88e1121_config_aneg(struct phy_device *phydev)
{
int err, oldpage, mscr;
@@ -207,6 +236,130 @@ static int m88e1318_config_aneg(struct phy_device *phydev)
return m88e1121_config_aneg(phydev);
}
+/**
+ * ethtool_adv_to_fiber_adv_t
+ * @ethadv: the ethtool advertisement settings
+ *
+ * A small helper function that translates ethtool advertisement
+ * settings to phy autonegotiation advertisements for the
+ * MII_ADV register for fiber link.
+ */
+static inline u32 ethtool_adv_to_fiber_adv_t(u32 ethadv)
+{
+ u32 result = 0;
+
+ if (ethadv & ADVERTISED_1000baseT_Half)
+ result |= ADVERTISE_FIBER_1000HALF;
+ if (ethadv & ADVERTISED_1000baseT_Full)
+ result |= ADVERTISE_FIBER_1000FULL;
+
+ if ((ethadv & ADVERTISE_PAUSE_ASYM) && (ethadv & ADVERTISE_PAUSE_CAP))
+ result |= LPA_PAUSE_ASYM_FIBER;
+ else if (ethadv & ADVERTISE_PAUSE_CAP)
+ result |= (ADVERTISE_PAUSE_FIBER
+ & (~ADVERTISE_PAUSE_ASYM_FIBER));
+
+ return result;
+}
+
+/**
+ * marvell_config_aneg_fiber - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ *
+ * Description: If auto-negotiation is enabled, we configure the
+ * advertising, and then restart auto-negotiation. If it is not
+ * enabled, then we write the BMCR. Adapted for fiber link in
+ * some Marvell's devices.
+ */
+static int marvell_config_aneg_fiber(struct phy_device *phydev)
+{
+ int changed = 0;
+ int err;
+ int adv, oldadv;
+ u32 advertise;
+
+ if (phydev->autoneg != AUTONEG_ENABLE)
+ return genphy_setup_forced(phydev);
+
+ /* Only allow advertising what this PHY supports */
+ phydev->advertising &= phydev->supported;
+ advertise = phydev->advertising;
+
+ /* Setup fiber advertisement */
+ adv = phy_read(phydev, MII_ADVERTISE);
+ if (adv < 0)
+ return adv;
+
+ oldadv = adv;
+ adv &= ~(ADVERTISE_FIBER_1000HALF | ADVERTISE_FIBER_1000FULL
+ | LPA_PAUSE_FIBER);
+ adv |= ethtool_adv_to_fiber_adv_t(advertise);
+
+ if (adv != oldadv) {
+ err = phy_write(phydev, MII_ADVERTISE, adv);
+ if (err < 0)
+ return err;
+
+ changed = 1;
+ }
+
+ if (changed == 0) {
+ /* Advertisement hasn't changed, but maybe aneg was never on to
+ * begin with? Or maybe phy was isolated?
+ */
+ int ctl = phy_read(phydev, MII_BMCR);
+
+ if (ctl < 0)
+ return ctl;
+
+ if (!(ctl & BMCR_ANENABLE) || (ctl & BMCR_ISOLATE))
+ changed = 1; /* do restart aneg */
+ }
+
+ /* Only restart aneg if we are advertising something different
+ * than we were before.
+ */
+ if (changed > 0)
+ changed = genphy_restart_aneg(phydev);
+
+ return changed;
+}
+
+static int m88e1510_config_aneg(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_COPPER);
+ if (err < 0)
+ goto error;
+
+ /* Configure the copper link first */
+ err = m88e1318_config_aneg(phydev);
+ if (err < 0)
+ goto error;
+
+ /* Then the fiber link */
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_FIBER);
+ if (err < 0)
+ goto error;
+
+ err = marvell_config_aneg_fiber(phydev);
+ if (err < 0)
+ goto error;
+
+ return phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_COPPER);
+
+error:
+ phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_M1111_COPPER);
+ return err;
+}
+
+static int marvell_config_init(struct phy_device *phydev)
+{
+ /* Set registers from marvell,reg-init DT property */
+ return marvell_of_reg_init(phydev);
+}
+
static int m88e1540_config_init(struct phy_device *phydev)
{
u16 reg;
@@ -246,7 +399,7 @@ static int m88e1540_config_init(struct phy_device *phydev)
if (ret < 0)
return ret;
- return 0;
+ return marvell_config_init(phydev);
}
static int m88e1121_config_init(struct phy_device *phydev)
@@ -289,9 +442,10 @@ static int m88e1121_config_init(struct phy_device *phydev)
if (ret < 0)
return ret;
- return 0;
+ return marvell_config_init(phydev);
}
+
static int m88e1318s_config_init(struct phy_device *phydev)
{
u16 reg;
@@ -311,6 +465,41 @@ static int m88e1318s_config_init(struct phy_device *phydev)
return m88e1121_config_init(phydev);
}
+static int m88e1510_config_init(struct phy_device *phydev)
+{
+ int err;
+ int temp;
+
+ /* SGMII-to-Copper mode initialization */
+ if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
+ /* Select page 18 */
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, 18);
+ if (err < 0)
+ return err;
+
+ /* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */
+ temp = phy_read(phydev, MII_88E1510_GEN_CTRL_REG_1);
+ temp &= ~MII_88E1510_GEN_CTRL_REG_1_MODE_MASK;
+ temp |= MII_88E1510_GEN_CTRL_REG_1_MODE_SGMII;
+ err = phy_write(phydev, MII_88E1510_GEN_CTRL_REG_1, temp);
+ if (err < 0)
+ return err;
+
+ /* PHY reset is necessary after changing MODE[2:0] */
+ temp |= MII_88E1510_GEN_CTRL_REG_1_RESET;
+ err = phy_write(phydev, MII_88E1510_GEN_CTRL_REG_1, temp);
+ if (err < 0)
+ return err;
+
+ /* Reset page selection */
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, 0);
+ if (err < 0)
+ return err;
+ }
+
+ return m88e1121_config_init(phydev);
+}
+
static struct phy_driver marvell_drivers[] = {
{
.phy_id = MARVELL_PHY_ID_88E1121R,
@@ -340,12 +529,21 @@ static struct phy_driver marvell_drivers[] = {
.read_status = &marvell_read_status,
},
{
+ .phy_id = MARVELL_PHY_ID_88E1510,
+ .phy_id_mask = MARVELL_PHY_ID_MASK,
+ .drv.name = "Marvell 88E1510",
+ .features = PHY_GBIT_FEATURES | SUPPORTED_FIBRE,
+ .config_init = &m88e1510_config_init,
+ .config_aneg = &m88e1510_config_aneg,
+ .read_status = &marvell_read_status,
+ },
+ {
.phy_id = MARVELL_PHY_ID_88E1540,
.phy_id_mask = MARVELL_PHY_ID_MASK,
.drv.name = "Marvell 88E1540",
.features = PHY_GBIT_FEATURES,
.config_init = &m88e1540_config_init,
- .config_aneg = &genphy_config_aneg,
+ .config_aneg = &m88e1510_config_aneg,
.read_status = &marvell_read_status,
},
};
--
2.11.0
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
