Hi Ivaylo,
On 7/30/25 15:12, Ivaylo Ivanov wrote:
> On 7/30/25 15:50, Ahmad Fatoum wrote:
>> Hi,
>>
>> On 7/30/25 13:18, Ivaylo Ivanov wrote:
>>> On 7/30/25 12:44, Ahmad Fatoum wrote:
>>>> Hi,
>>>>
>>>> On 7/30/25 11:16, Ivaylo Ivanov wrote:
>>>>> On 7/30/25 11:48, Ahmad Fatoum wrote:
>>>>>> Hi Ivaylo,
>>>>>>
>>>>>> On 7/29/25 22:36, Ivaylo Ivanov wrote:
>>>>>>> Add support for Samsung Galaxy S20 5G, based on exynos990, to the
>>>>>>> current samsung board support. This platform, just like exynos8895,
>>>>>>> needs a bit to be set in order to allow the framebuffer to refresh.
>>>>>>>
>>>>>> Oh, a shame that I sold the old S20 FE I had. :/
>>>>>> I still have a rooted S10e though. I should give this a try when I have
>>>>>> time.
>>>>> Heh, I was thinking about getting an s10e to bring up mainline linux on
>>>>> it,
>>>>> but I do have quite a lot of devices to work on right now. At the very
>>>>> least,
>>>>> I expect to throw in support for 7580 and 8890 in the future for both
>>>>> mainline linux and barebox. The plan ideally will be to bring up support
>>>>> for
>>>>> exynos7580 in barebox to a decent state, with mmc and usb working at
>>>>> least.
>>>>> S20 series are decently supported, but nothing exciting yet.
>>>> Cool stuff. Looking forward to it. :-)
>>>>
>>>>> Another qustion: are there any plans to support booting fit images from an
>>>>> address in ram instead of a file? I suspect porting over all the ufs
>>>>> stuff from
>>>>> linux will be a hassle
>>>> It's something we will want sooner or later, but yes, it will likely be
>>>> involved.
>>>>
>>>>> , so for S20 (which does not have an sd card slot, only ufs)
>>>>> booting a fit image that s-boot has loaded into ram for us might be neat.
>>>>> As far as I've seen, only "go" can do that, but not "bootm".
>>>> $ addpart /dev/ram0 0x1000@0x1000(fit)
>>>> $ bootm /dev/ram0.fit
>>>>
>>>> would've been the workaround so far.
>>> Oh, nice. I'll give it a shot and if it works, I'll include it
>>> in a config in the board dir as default boot behavior
>>> (we really cannot interact with the console yet anyways).
>> I think a convenient behavior, at least during development is to set
>> autoboot=menu and set a menu timeout. Then add a config option that
>> remaps volume up/down to up/down and some button as return and you
>> should at least be able to navigate the menu.
>>
>> After timeout expires, system would boot normally.
>
> Hm, I haven't thought of that. Mapping keys will need a pinctrl/gpio driver
> though, so I think it will be best to just have default boot behavior as
> bootm'ing a fit image from ram, while also having autoboot=menu
> and a timeout set. That way we can expand it after adding keys in the
> future. Does that sound good?
Ye, sure. I am just talking where we could go from here in future.
Keep up the good work.
Cheers,
Ahmad
>
> Best regards,
> Ivaylo
>
>>
>>>> Since the fuzzing infrastructure has been merged, we also have
>>>> ramdisk_init, which sets up a block device on top of a memory buffer
>>>> without block layer caching. I think that's sufficient to implement
>>>> losetup(8), which would go beyond addpart and even allow mounting file
>>>> systems from the loop device.
>>> I see. Looking forward to that.
>>>
>>> Best regards,
>>> Ivaylo.
>>>
>>>> Cheers,
>>>> Ahmad
>>>>
>>>>
>>>>
>>>>> Best regards,
>>>>> Ivaylo
>>>>>
>>>>>>> diff --git a/arch/arm/dts/exynos990-x1s.dts
>>>>>>> b/arch/arm/dts/exynos990-x1s.dts
>>>>>>> new file mode 100644
>>>>>>> index 00000000..19d59eaa
>>>>>>> --- /dev/null
>>>>>>> +++ b/arch/arm/dts/exynos990-x1s.dts
>>>>>>> @@ -0,0 +1,13 @@
>>>>>>> +// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
>>>>>>> +/*
>>>>>>> + * Samsung Galaxy S20 5G (x1s/SM-G981B) barebox device tree source
>>>>>>> + *
>>>>>>> + * Copyright (c) 2025, Ivaylo Ivanov <ivo.ivanov.ivan...@gmail.com>
>>>>>>> + */
>>>>>>> +
>>>>>>> +/dts-v1/;
>>>>>>> +#include <arm64/exynos/exynos990-x1s.dts>
>>>>>>> +
>>>>>>> +/ {
>>>>>>> + barebox,disable-deep-probe;
>>>>>> Same comment: we want deep probe as default eventually. Did you run into
>>>>>> problems without this?
>>>>>>
>>>>>> Cheers,
>>>>>> Ahmad
>>>>>>
>>>>>>> +};
>>>
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
