here it's the output of what u requested
[EMAIL PROTECTED]:~$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
eth1 Scan completed :
Cell 01 - Address: 00:0C:41:19:2D:C1
ESSID:"<hidden>"
Protocol:IEEE 802.11b
Mode:Master
Frequency:2.462 GHz (Channel 11)
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
Quality=98/100 Signal level=-42 dBm Noise level=-256
dBm
Extra: Last beacon: 717ms ago
[EMAIL PROTECTED]:~$ dmesg|grep bcm
[ 28.759141] bcm43xx driver
this is the network card:
05:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI
(rev 01)
and this is what happen when i ping my router (in the case that it connects
to me when i'm really near,but not always happen) and i get far away from
the router of some meters:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data
64 bytes from 192.168.1.1: icmp_seq=1 ttl=150 time=2.49 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=150 time=2.35 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=150 time=2.36 ms
64 bytes from 192.168.1.1: icmp_seq=7 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=8 ttl=150 time=2.36 ms
64 bytes from 192.168.1.1: icmp_seq=9 ttl=150 time=2.35 ms
64 bytes from 192.168.1.1: icmp_seq=10 ttl=150 time=5.69 ms
64 bytes from 192.168.1.1: icmp_seq=11 ttl=150 time=2.36 ms
64 bytes from 192.168.1.1: icmp_seq=12 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=13 ttl=150 time=2.37 ms
64 bytes from 192.168.1.1: icmp_seq=14 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=15 ttl=150 time=2.39 ms
64 bytes from 192.168.1.1: icmp_seq=16 ttl=150 time=2.36 ms
64 bytes from 192.168.1.1: icmp_seq=17 ttl=150 time=2.36 ms
64 bytes from 192.168.1.1: icmp_seq=18 ttl=150 time=25.2 ms
64 bytes from 192.168.1.1: icmp_seq=19 ttl=150 time=4.94 ms
64 bytes from 192.168.1.1: icmp_seq=20 ttl=150 time=4.07 ms
64 bytes from 192.168.1.1: icmp_seq=21 ttl=150 time=2.47 ms
64 bytes from 192.168.1.1: icmp_seq=22 ttl=150 time=2.35 ms
64 bytes from 192.168.1.1: icmp_seq=23 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=24 ttl=150 time=2.35 ms
64 bytes from 192.168.1.1: icmp_seq=25 ttl=150 time=2.35 ms
64 bytes from 192.168.1.1: icmp_seq=26 ttl=150 time=2.37 ms
64 bytes from 192.168.1.1: icmp_seq=27 ttl=150 time=2.40 ms
64 bytes from 192.168.1.1: icmp_seq=28 ttl=150 time=15.3 ms
64 bytes from 192.168.1.1: icmp_seq=29 ttl=150 time=2.71 ms
64 bytes from 192.168.1.1: icmp_seq=30 ttl=150 time=2.38 ms
64 bytes from 192.168.1.1: icmp_seq=31 ttl=150 time=654 ms
64 bytes from 192.168.1.1: icmp_seq=32 ttl=150 time=9.89 ms
64 bytes from 192.168.1.1: icmp_seq=33 ttl=150 time=70.7 ms
64 bytes from 192.168.1.1: icmp_seq=34 ttl=150 time=565 ms
64 bytes from 192.168.1.1: icmp_seq=35 ttl=150 time=6.12 ms
64 bytes from 192.168.1.1: icmp_seq=36 ttl=150 time=75.9 ms
64 bytes from 192.168.1.1: icmp_seq=37 ttl=150 time=340 ms
64 bytes from 192.168.1.1: icmp_seq=38 ttl=150 time=937 ms
64 bytes from 192.168.1.1: icmp_seq=40 ttl=150 time=115 ms
64 bytes from 192.168.1.1: icmp_seq=44 ttl=150 time=193 ms
64 bytes from 192.168.1.1: icmp_seq=45 ttl=150 time=266 ms
64 bytes from 192.168.1.1: icmp_seq=50 ttl=150 time=1165 ms
64 bytes from 192.168.1.1: icmp_seq=54 ttl=150 time=40.8 ms
>From 192.168.1.80 icmp_seq=101 Destination Host Unreachable
thanks for helping,
regards
ruggiero
----- Original Message -----
From: "Larry Finger" <[EMAIL PROTECTED]>
To: "Ruggiero" <[EMAIL PROTECTED]>
Cc: <[email protected]>
Sent: Wednesday, November 07, 2007 7:04 PM
Subject: Re: BCM94311MCG
> Ruggiero wrote:
>> i don't know if it's this the place to write about this problem...but if
>> u say me where i should post the problem i'll do...here it comes...
>> i have installed ubuntu 7.10 and i recompiled the kernel with to
>> 2.6.23.1 because on the earlier kernel my wireless card didn't work with
>> bcm43xx drivers but only with ndiswrapper..(i could see the access point
>> but couldn't connect to it)
>> now after recompiled i installed bcm43xx-fwcutter and by this i
>> extracted the firmware using wl_apsta-3.130.20.0.o .. now as for the
>> earlier kernel i can see the access point by typing "sudo iwlist scan"
>> but i can't connect to it..sometime i can but only if i'm near to the
>> access point(two meters) but anyway speed is really slow :(
>>
>> the card BCM94311MCG rev01 this is what comes out by typing lspci
>> hope u can help me and if u need more dates i'll be glad to give...
>
> What is the output from a 'dmesg | grep bcm' command? In addition, please
> send the output of 'iwlist
> scan'.
>
> Larry
--
Io utilizzo la versione gratuita di SPAMfighter per utenti privati. Sino ad ora
ha rimosso 815 mail spam.
Gli utenti paganti non hanno questo messaggio nelle loro email .
Prova gratuitamente SPAMfighter qui:http://www.spamfighter.com/lit
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
