Debian Sid 64 bit AMD64 X2 Kernel 2.6.24-smp w/ 4311_2 patch applied from here: http://linuxwireless.org/download/b43/patch_2.6.24_for_4311_2
lspci 03:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 02) _______________________________________________________ My kernel configuration: # zcat /proc/config.gz |grep B43 CONFIG_B43=m CONFIG_B43_PCI_AUTOSELECT=y CONFIG_B43_PCICORE_AUTOSELECT=y CONFIG_B43_LEDS=y CONFIG_B43_RFKILL=y CONFIG_B43_DEBUG=y CONFIG_B43_DMA=y CONFIG_B43_PIO=y CONFIG_B43_DMA_AND_PIO_MODE=y # CONFIG_B43_DMA_MODE is not set # CONFIG_B43_PIO_MODE is not set CONFIG_B43LEGACY=m CONFIG_B43LEGACY_PCI_AUTOSELECT=y CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y CONFIG_B43LEGACY_LEDS=y CONFIG_B43LEGACY_RFKILL=y CONFIG_B43LEGACY_DEBUG=y CONFIG_B43LEGACY_DMA=y CONFIG_B43LEGACY_PIO=y CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y # CONFIG_B43LEGACY_DMA_MODE is not set # CONFIG_B43LEGACY_PIO_MODE is not set I have completely disabled BCM43xx # zcat /proc/config.gz |grep BCM43 # CONFIG_BCM43XX is not set ________________________________________________________ # lsmod|grep b43 b43 161840 0 rfkill 9680 3 rfkill_input,b43 mac80211 143948 1 b43 led_class 6664 1 b43 input_polldev 6352 1 b43 ________________________________________________________ dmesg|grep b43 b43-phy0: Broadcom 4311 WLAN found b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 9 b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2 input: b43-phy0 as /devices/virtual/input/input9 b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) b43-phy0 debug: Chip initialized b43-phy0 debug: 64-bit DMA initialized Registered led device: b43-phy0:tx Registered led device: b43-phy0:rx Registered led device: b43-phy0:radio b43-phy0 ERROR: PHY transmission error b43-phy0 debug: Wireless interface started b43-phy0 debug: Adding Interface type 2 b43-phy0 debug: Removing Interface type 2 b43-phy0 debug: Wireless interface stopped b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 1/64 b43-phy0 debug: DMA-64 0x0340 (TX) max used slots: 0/128 b43-phy0 debug: DMA-64 0x0300 (TX) max used slots: 0/128 b43-phy0 debug: DMA-64 0x02C0 (TX) max used slots: 0/128 b43-phy0 debug: DMA-64 0x0280 (TX) max used slots: 0/128 b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 2/128 b43-phy0 debug: DMA-64 0x0200 (TX) max used slots: 0/128 input: b43-phy0 as /devices/virtual/input/input10 b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) b43-phy0 debug: Chip initialized b43-phy0 debug: 64-bit DMA initialized Registered led device: b43-phy0:tx Registered led device: b43-phy0:rx Registered led device: b43-phy0:radio b43-phy0 debug: Wireless interface started b43-phy0 debug: Adding Interface type 2 The device configures and comes up no problem. I can even obtain an i.p. via DHCP however the connection only stays up for a matter of seconds until I get this error: b43-phy0 ERROR: PHY transmission error at which point the device is useless and cannot be made to connect again until after a reboot. Currently I do use WPA however I've even tried disabling encryption entirely but the problem persists. I'm not sure what to try at this point. If you'd like further info from my system just say so and I'll be glad to post it. -- glenn greenfield _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
