On Feb 8, 2008 6:01 PM, Jory A. Pratt <[EMAIL PROTECTED]> wrote: > > glenn greenfield wrote: > > eth0: no link during initialization. > > NET: Registered protocol family 10 > > lo: Disabled Privacy Extensions > > ADDRCONF(NETDEV_UP): eth0: link is not ready > > ADDRCONF(NETDEV_UP): wlan0: link is not ready > > lp: driver loaded but no devices found > > ppdev: user-space parallel port driver > > wlan0: Initial auth_alg=0 > > wlan0: authenticate with AP 00:12:17:2f:bb:b6 > > wlan0: RX authentication from 00:12:17:2f:bb:b6 (alg=0 transaction=2 > > status=0) > > wlan0: authenticated > > wlan0: associate with AP 00:12:17:2f:bb:b6 > > wlan0: RX AssocResp from 00:12:17:2f:bb:b6 (capab=0x411 status=0 aid=2) > > wlan0: associated > > wlan0: CTS protection enabled (BSSID=00:12:17:2f:bb:b6) > > wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0 > > wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0 > > wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30 > > wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15 > > ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > > Clocksource tsc unstable (delta = -158243821 ns) > > wlan0: no IPv6 routers present > > b43-phy0 debug: Removing Interface type 2 > > b43-phy0 debug: Wireless interface stopped > > b43-phy0 debug: DMA-64 0x0200 (RX) max used slots: 1/64 > > b43-phy0 debug: DMA-64 0x0340 (TX) max used slots: 0/128 > > b43-phy0 debug: DMA-64 0x0300 (TX) max used slots: 0/128 > > b43-phy0 debug: DMA-64 0x02C0 (TX) max used slots: 0/128 > > b43-phy0 debug: DMA-64 0x0280 (TX) max used slots: 0/128 > > b43-phy0 debug: DMA-64 0x0240 (TX) max used slots: 4/128 > > b43-phy0 debug: DMA-64 0x0200 (TX) max used slots: 0/128 > > input: b43-phy0 as /devices/virtual/input/input10 > > b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) > > b43-phy0 debug: Chip initialized > > b43-phy0 debug: 64-bit DMA initialized > > Registered led device: b43-phy0:tx > > Registered led device: b43-phy0:rx > > Registered led device: b43-phy0:radio > > b43-phy0 debug: Wireless interface started > > b43-phy0 debug: Adding Interface type 2 > > ADDRCONF(NETDEV_UP): wlan0: link is not ready > > eth0: no link during initialization. > > ADDRCONF(NETDEV_UP): eth0: link is not ready > > wlan0: CTS protection enabled (BSSID=00:12:17:2f:bb:b6) > > wlan0: RX deauthentication from 00:12:17:2f:bb:b6 (reason=16) > > wlan0: deauthenticated > > wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate > > wlan0: Initial auth_alg=0 > > wlan0: authenticate with AP 00:12:17:2f:bb:b6 > > wlan0: RX deauthentication from 00:12:17:2f:bb:b6 (reason=6) > > wlan0: RX authentication from 00:12:17:2f:bb:b6 (alg=0 transaction=2 > > status=0) > > wlan0: authenticated > > wlan0: associate with AP 00:12:17:2f:bb:b6 > > wlan0: RX AssocResp from 00:12:17:2f:bb:b6 (capab=0x411 status=0 aid=2) > > wlan0: associated > > wlan0: CTS protection enabled (BSSID=00:12:17:2f:bb:b6) > > wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0 > > wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0 > > wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30 > > wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15 > > ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > > wlan0: no IPv6 routers present > > nvidia: module license 'NVIDIA' taints kernel. > > ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16 > > ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LGPU] -> GSI 16 (level, > > low) -> IRQ 16 > > PCI: Setting latency timer of device 0000:00:12.0 to 64 > > NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.09 Fri Jan 11 > > 14:04:37 PST 2008 > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > b43-phy0 ERROR: PHY transmission error > > printk: 9 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 9 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 3 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 2 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 5 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 3 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 2 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 1 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 2 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 5 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > printk: 2 messages suppressed. > > b43-phy0 ERROR: PHY transmission error > > > > Perhaps I have the wrong firmware? I used what was in Debian on my > > first attempts but it seems that version is outdated or just incorrect > > for my wireless card. So I tried this: > > > > wget http://mirror2.openwrt.org/sources/broadcom-wl-4.150.10.5.tar.bz2 > > tar xjvf broadcom-wl-4.150.10.5.tar.bz2 > > cd broadcom-wl-4.150.10.5 > > b43-fwcutter -w /lib/firmware driver/wl_apsta_mimo.o > > Sorry, the input file is either wrong or not supported by b43-fwcutter. > > This file has an unknown MD5sum cb8d70972b885b1f8883b943c0261a3c. > > > > I repeated this several times with the same results each time. Not > > sure what to do from this point. > > > > > > > > There is something more here then what meets the eye. I run a dv6609 and > works fine with wireless-2.6 git tree. If you could pull down the latest > wireless-2.6 git tree and test it. It may be just a bug in stable that > has not been fixed yet. You may also need to pass pci=routeirq threw > your bootloader. A full dmesg > will suggest such and does resolve some of the issues with hp's terrible > design flaw in the bios. > > -Jory >
I have built and installed the compat-wireless-2.6 The installation went fine, the card comes up and even obtains an i.p. but that's where it ends. dmesg tells me that I have an old firmware version and to get the latest which I have attempted to do but I cannot extract the firmware broadcom-wl-4.150.10.5 > b43-fwcutter driver/wl_apsta_mimo.o Sorry, the input file is either wrong or not supported by b43-fwcutter. This file has an unknown MD5sum cb8d70972b885b1f8883b943c0261a3c. I have attempted to extract the firmware at least 12 times on 2 different systems (both Debian) with the same results each time. I used wget to download the firmware as well as Firefox. Am I doing it incorrectly? Is it possible to download the extracted firmware someplace? -- glenn greenfield _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
