Hello, I'm trying to install Arch on my BBB rev C. using the described method on https://archlinuxarm.org/platforms/armv7/ti/beaglebone-black but it can't find my zImage, whilst it is present in the boot folder. It hangs while the two outer LEDS are on with the following message. I also posted this question on the ArchLinux arm forum https://archlinuxarm.org/forum/viewtopic.php?f=48&t=10563 but time is paramount for me at the moment.
> Net: <ethaddr> not set. Validating first E-fuse MAC Phy 0 not found cpsw Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 starting USB... USB0: Port not available. switch to partitions #0, OK mmc0 is current device mmc found on device 0 Checking for: /boot/uEnv.txt ... gpio: pin 54 (gpio 54) value is 1 gpio: pin 55 (gpio 55) value is 1 reading /boot/zImage ** Unable to read file /boot/zImage ** No kernel found gpio: pin 54 (gpio 54) value is 0 gpio: pin 55 (gpio 55) value is 0 switch to partitions #0, OK mmc1(part 0) is current device mmc found on device 1 Checking for: /boot/uEnv.txt ... gpio: pin 54 (gpio 54) value is 1 1184 bytes read in 22 ms (51.8 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uenvcmd is set ... gpio: pin 55 (gpio 55) value is 1 ** File not found /boot/zImage ** No kernel found gpio: pin 54 (gpio 54) value is 0 gpio: pin 55 (gpio 55) value is 0 USB is stopped. Please issue 'usb start' first. USB is stopped. Please issue 'usb start' first. gpio: pin 54 (gpio 54) value is 0 gpio: pin 55 (gpio 55) value is 0 gpio: pin 56 (gpio 56) value is 1 U-Boot# > > Checked the md5sum of the downloaded image and it checks out, performed sync's between each writing operation. I tried multiple changes to the uEnv.txt suggested at https://archlinuxarm.org/forum/viewtopic.php?f=48&t=8242&p=44246&hilit=zImage#p44246[ such as: > uenvcmd=run findfdt; if test $board_name = A335BNLT; then i2c mw 0x24 1 0x3e; setenv mmcdev 1; mmc dev ${mmcdev}; if mmc rescan; then setenv mmc1 1;else setenv mmc1 0;fi;fi;setenv mmcdev 0; mmc dev ${mmcdev}; if mmc rescan; then setenv mmc0 1;else setenv mmc0 0;fi;if run loaduimage; then run loadfdt;run mmcboot;fi; mmcroot=/dev/mmcblk0p2 rw loadfdt=ext4load mmc ${mmcdev}:2 ${fdtaddr} /boot/dtbs/${fdtfile} loaduimage=if ext4load mmc 0:2 ${loadaddr} /boot/zImage; then setenv mmcdev 0; else setenv mmcdev 1; if test $mmc0 = 1; then setenv mmcroot /dev/mmcblk1p2 rw; fi; ext4load mmc 1:2 ${loadaddr} /boot/zImage; fi mmcboot=echo Booting from mmc ...; run mmcargs; bootz ${loadaddr} - ${fdtaddr} > > I also tried to move the boot folder to an alternative partition formated in fat and create the U-boot via: > > dd if=boot/MLO of=/dev/mmcblk0 count=1 seek=1 conv=notrunc bs=128k dd if=boot/u-boot.img of=/dev/mmcblk0 count=2 seek=1 conv=notrunc bs=384k > > What am I missing? Every suggestion is more then welcome. Best regards -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/e05aed65-44f1-46ee-a1ed-43ad86d4b38a%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
