So . . . put sdcard into another Linux machine. Then . . . sudo mount /dev/sdxx /media/rootfs ls /media/rootfs/boot
What output do you get ? On Wed, Jul 13, 2016 at 1:16 PM, Jelle Spijker <spijker.je...@gmail.com> wrote: > Hello, > > I'm trying to install Arch on my BBB rev C. using the described method on > https://archlinuxarm.org/platforms/armv7/ti/beaglebone-black but it > can't find my zImage, whilst it is present in the boot folder. It hangs > while the two outer LEDS are on with the following message. I also posted > this question on the ArchLinux arm forum > https://archlinuxarm.org/forum/viewtopic.php?f=48&t=10563 but time is > paramount for me at the moment. > > >> Net: <ethaddr> not set. Validating first E-fuse MAC > Phy 0 not found > cpsw > Hit any key to stop autoboot: 0 > gpio: pin 53 (gpio 53) value is 1 > starting USB... > USB0: Port not available. > switch to partitions #0, OK > mmc0 is current device > mmc found on device 0 > Checking for: /boot/uEnv.txt ... > gpio: pin 54 (gpio 54) value is 1 > gpio: pin 55 (gpio 55) value is 1 > reading /boot/zImage > ** Unable to read file /boot/zImage ** > No kernel found > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 55 (gpio 55) value is 0 > switch to partitions #0, OK > mmc1(part 0) is current device > mmc found on device 1 > Checking for: /boot/uEnv.txt ... > gpio: pin 54 (gpio 54) value is 1 > 1184 bytes read in 22 ms (51.8 KiB/s) > Loaded environment from /boot/uEnv.txt > Checking if uenvcmd is set ... > gpio: pin 55 (gpio 55) value is 1 > ** File not found /boot/zImage ** > No kernel found > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 55 (gpio 55) value is 0 > USB is stopped. Please issue 'usb start' first. > USB is stopped. Please issue 'usb start' first. > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 55 (gpio 55) value is 0 > gpio: pin 56 (gpio 56) value is 1 > U-Boot# > >> >> > Checked the md5sum of the downloaded image and it checks out, performed > sync's between each writing operation. > I tried multiple changes to the uEnv.txt suggested at > https://archlinuxarm.org/forum/viewtopic.php?f=48&t=8242&p=44246&hilit=zImage#p44246[ > such > as: > > >> uenvcmd=run findfdt; if test $board_name = A335BNLT; then i2c mw 0x24 1 > 0x3e; setenv mmcdev 1; mmc dev ${mmcdev}; if mmc rescan; then setenv mmc1 > 1;else setenv mmc1 0;fi;fi;setenv mmcdev 0; mmc dev ${mmcdev}; if mmc > rescan; then setenv mmc0 1;else setenv mmc0 0;fi;if run loaduimage; then > run loadfdt;run mmcboot;fi; > mmcroot=/dev/mmcblk0p2 rw > loadfdt=ext4load mmc ${mmcdev}:2 ${fdtaddr} /boot/dtbs/${fdtfile} > loaduimage=if ext4load mmc 0:2 ${loadaddr} /boot/zImage; then setenv > mmcdev 0; else setenv mmcdev 1; if test $mmc0 = 1; then setenv mmcroot > /dev/mmcblk1p2 rw; fi; ext4load mmc 1:2 ${loadaddr} /boot/zImage; fi > mmcboot=echo Booting from mmc ...; run mmcargs; bootz ${loadaddr} - > ${fdtaddr} > >> >> > I also tried to move the boot folder to an alternative partition formated > in fat and create the U-boot via: > >> >> dd if=boot/MLO of=/dev/mmcblk0 count=1 seek=1 conv=notrunc bs=128k > dd if=boot/u-boot.img of=/dev/mmcblk0 count=2 seek=1 conv=notrunc bs=384k > >> >> > What am I missing? > > Every suggestion is more then welcome. > > Best regards > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to beagleboard+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/beagleboard/e05aed65-44f1-46ee-a1ed-43ad86d4b38a%40googlegroups.com > <https://groups.google.com/d/msgid/beagleboard/e05aed65-44f1-46ee-a1ed-43ad86d4b38a%40googlegroups.com?utm_medium=email&utm_source=footer> > . > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CALHSORoOCP1Zkx3LsqfWKWUNM6tjO7T_TWkAmMzLmgPTEQm6NQ%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.
