drwxr-xr-x 2 root root 4.0K Jul 1 03:57 dtbs -rw-r--r-- 1 root root 74K Jun 8 2015 MLO -rw-r--r-- 1 root root 389K Jun 8 2015 u-boot.img -rw-r--r-- 1 root root 104 Jul 13 22:03 uEnv.txt -rwxr-xr-x 1 root root 5.2M Jul 1 03:57 zImage
Op woensdag 13 juli 2016 22:22:38 UTC+2 schreef William Hermans: > > So . . . put sdcard into another Linux machine. Then . . . > > sudo mount /dev/sdxx /media/rootfs > ls /media/rootfs/boot > > What output do you get ? > > On Wed, Jul 13, 2016 at 1:16 PM, Jelle Spijker <[email protected] > <javascript:>> wrote: > >> Hello, >> >> I'm trying to install Arch on my BBB rev C. using the described method on >> https://archlinuxarm.org/platforms/armv7/ti/beaglebone-black but it >> can't find my zImage, whilst it is present in the boot folder. It hangs >> while the two outer LEDS are on with the following message. I also posted >> this question on the ArchLinux arm forum >> https://archlinuxarm.org/forum/viewtopic.php?f=48&t=10563 but time is >> paramount for me at the moment. >> >> >>> Net: <ethaddr> not set. Validating first E-fuse MAC >> Phy 0 not found >> cpsw >> Hit any key to stop autoboot: 0 >> gpio: pin 53 (gpio 53) value is 1 >> starting USB... >> USB0: Port not available. >> switch to partitions #0, OK >> mmc0 is current device >> mmc found on device 0 >> Checking for: /boot/uEnv.txt ... >> gpio: pin 54 (gpio 54) value is 1 >> gpio: pin 55 (gpio 55) value is 1 >> reading /boot/zImage >> ** Unable to read file /boot/zImage ** >> No kernel found >> gpio: pin 54 (gpio 54) value is 0 >> gpio: pin 55 (gpio 55) value is 0 >> switch to partitions #0, OK >> mmc1(part 0) is current device >> mmc found on device 1 >> Checking for: /boot/uEnv.txt ... >> gpio: pin 54 (gpio 54) value is 1 >> 1184 bytes read in 22 ms (51.8 KiB/s) >> Loaded environment from /boot/uEnv.txt >> Checking if uenvcmd is set ... >> gpio: pin 55 (gpio 55) value is 1 >> ** File not found /boot/zImage ** >> No kernel found >> gpio: pin 54 (gpio 54) value is 0 >> gpio: pin 55 (gpio 55) value is 0 >> USB is stopped. Please issue 'usb start' first. >> USB is stopped. Please issue 'usb start' first. >> gpio: pin 54 (gpio 54) value is 0 >> gpio: pin 55 (gpio 55) value is 0 >> gpio: pin 56 (gpio 56) value is 1 >> U-Boot# >> >>> >>> >> Checked the md5sum of the downloaded image and it checks out, performed >> sync's between each writing operation. >> I tried multiple changes to the uEnv.txt suggested at >> https://archlinuxarm.org/forum/viewtopic.php?f=48&t=8242&p=44246&hilit=zImage#p44246[ >> such >> as: >> >> >>> uenvcmd=run findfdt; if test $board_name = A335BNLT; then i2c mw 0x24 1 >> 0x3e; setenv mmcdev 1; mmc dev ${mmcdev}; if mmc rescan; then setenv mmc1 >> 1;else setenv mmc1 0;fi;fi;setenv mmcdev 0; mmc dev ${mmcdev}; if mmc >> rescan; then setenv mmc0 1;else setenv mmc0 0;fi;if run loaduimage; then >> run loadfdt;run mmcboot;fi; >> mmcroot=/dev/mmcblk0p2 rw >> loadfdt=ext4load mmc ${mmcdev}:2 ${fdtaddr} /boot/dtbs/${fdtfile} >> loaduimage=if ext4load mmc 0:2 ${loadaddr} /boot/zImage; then setenv >> mmcdev 0; else setenv mmcdev 1; if test $mmc0 = 1; then setenv mmcroot >> /dev/mmcblk1p2 rw; fi; ext4load mmc 1:2 ${loadaddr} /boot/zImage; fi >> mmcboot=echo Booting from mmc ...; run mmcargs; bootz ${loadaddr} - >> ${fdtaddr} >> >>> >>> >> I also tried to move the boot folder to an alternative partition formated >> in fat and create the U-boot via: >> >>> >>> dd if=boot/MLO of=/dev/mmcblk0 count=1 seek=1 conv=notrunc bs=128k >> dd if=boot/u-boot.img of=/dev/mmcblk0 count=2 seek=1 conv=notrunc bs=384k >> >>> >>> >> What am I missing? >> >> Every suggestion is more then welcome. >> >> Best regards >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected] <javascript:>. >> To view this discussion on the web visit >> https://groups.google.com/d/msgid/beagleboard/e05aed65-44f1-46ee-a1ed-43ad86d4b38a%40googlegroups.com >> >> <https://groups.google.com/d/msgid/beagleboard/e05aed65-44f1-46ee-a1ed-43ad86d4b38a%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> For more options, visit https://groups.google.com/d/optout. >> > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/a732068b-d9e9-4266-b574-f8ec04553274%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
