I burn a new microSD card with the same image and now the linux it's boot > > bone-debian-8.10-seeed-iot-armhf-2018-02-01-4gb.img
Try again and now this is the otuput > config-pin p8.11 pruout P8_11 pinmux file not found! > bash: /sys/devices/platform/ocp/ocp*P8_11_pinmux/state: No such file or > directory > Cannot write pinmux file: /sys/devices/platform/ocp/ocp*P8_11_pinmux/state here the new sytem info sudo /opt/scripts/tools/version.sh > git:/opt/scripts/:[ad016da40de5805f1a6f981cbb6c454b1a7f244b] > eeprom:[A335BNLTGW1ABBGW16050761] > model:[TI_AM335x_BeagleBone_Green_Wireless] > dogtag:[BeagleBoard.org Debian Image 2018-02-01] > bootloader:[microSD-(push-button)]:[/dev/mmcblk0]:[U-Boot > 2018.01-00002-g9aa111a004] > kernel:[4.4.113-ti-r145] > nodejs:[v0.12.18] > uboot_overlay_options:[enable_uboot_overlays=1] > > uboot_overlay_options:[uboot_overlay_pru=/lib/firmware/AM335X-PRU-UIO-00A0.dtbo] > uboot_overlay_options:[enable_uboot_cape_universal=1] > pkg:[bb-cape-overlays]:[4.4.20180126.0-0rcnee0~jessie+20180126] > pkg:[bb-wl18xx-firmware]:[1.20170829-0rcnee2~jessie+20180104] > pkg:[firmware-ti-connectivity]:[20170823-1rcnee0~jessie+20170830] > groups:[debian : debian adm kmem dialout cdrom floppy audio dip video > plugdev users systemd-journal netdev i2c bluetooth cloud9ide gpio pwm eqep > admin spi tisdk weston-launch xenomai] > dmesg | grep pinctrl-single > [ 1.212781] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 > size 568 > dmesg | grep gpio-of-helper > [ 1.213903] gpio-of-helper ocp:cape-universal: Allocated GPIO id=0 > [ 1.214074] gpio-of-helper ocp:cape-universal: Allocated GPIO id=1 > [ 1.214218] gpio-of-helper ocp:cape-universal: Allocated GPIO id=2 > [ 1.214357] gpio-of-helper ocp:cape-universal: Allocated GPIO id=3 > [ 1.214497] gpio-of-helper ocp:cape-universal: Allocated GPIO id=4 > [ 1.214630] gpio-of-helper ocp:cape-universal: Allocated GPIO id=5 > [ 1.214762] gpio-of-helper ocp:cape-universal: Allocated GPIO id=6 > [ 1.214902] gpio-of-helper ocp:cape-universal: Allocated GPIO id=7 > [ 1.215048] gpio-of-helper ocp:cape-universal: Allocated GPIO id=8 > [ 1.215192] gpio-of-helper ocp:cape-universal: Allocated GPIO id=9 > [ 1.215327] gpio-of-helper ocp:cape-universal: Allocated GPIO id=10 > [ 1.215466] gpio-of-helper ocp:cape-universal: Allocated GPIO id=11 > [ 1.215609] gpio-of-helper ocp:cape-universal: Allocated GPIO id=12 > [ 1.215746] gpio-of-helper ocp:cape-universal: Allocated GPIO id=13 > [ 1.215882] gpio-of-helper ocp:cape-universal: Allocated GPIO id=14 > [ 1.216023] gpio-of-helper ocp:cape-universal: Allocated GPIO id=15 > [ 1.216634] gpio-of-helper ocp:cape-universal: Allocated GPIO id=16 > [ 1.216813] gpio-of-helper ocp:cape-universal: Allocated GPIO id=17 > [ 1.217031] gpio-of-helper ocp:cape-universal: Allocated GPIO id=18 > [ 1.217194] gpio-of-helper ocp:cape-universal: Allocated GPIO id=19 > [ 1.217341] gpio-of-helper ocp:cape-universal: Allocated GPIO id=20 > [ 1.217481] gpio-of-helper ocp:cape-universal: Allocated GPIO id=21 > [ 1.217619] gpio-of-helper ocp:cape-universal: Allocated GPIO id=22 > [ 1.217763] gpio-of-helper ocp:cape-universal: Allocated GPIO id=23 > [ 1.217902] gpio-of-helper ocp:cape-universal: Allocated GPIO id=24 > [ 1.218040] gpio-of-helper ocp:cape-universal: Allocated GPIO id=25 > [ 1.218193] gpio-of-helper ocp:cape-universal: Allocated GPIO id=26 > [ 1.218338] gpio-of-helper ocp:cape-universal: Allocated GPIO id=27 > [ 1.218486] gpio-of-helper ocp:cape-universal: Allocated GPIO id=28 > [ 1.218627] gpio-of-helper ocp:cape-universal: Allocated GPIO id=29 > [ 1.218769] gpio-of-helper ocp:cape-universal: Allocated GPIO id=30 > [ 1.218916] gpio-of-helper ocp:cape-universal: Allocated GPIO id=31 > [ 1.219057] gpio-of-helper ocp:cape-universal: Allocated GPIO id=32 > [ 1.219197] gpio-of-helper ocp:cape-universal: Allocated GPIO id=33 > [ 1.219349] gpio-of-helper ocp:cape-universal: Allocated GPIO id=34 > [ 1.219494] gpio-of-helper ocp:cape-universal: Allocated GPIO id=35 > [ 1.219643] gpio-of-helper ocp:cape-universal: Allocated GPIO id=36 > [ 1.219791] gpio-of-helper ocp:cape-universal: Allocated GPIO id=37 > [ 1.219933] gpio-of-helper ocp:cape-universal: Allocated GPIO id=38 > [ 1.220317] gpio-of-helper ocp:cape-universal: Allocated GPIO id=39 > [ 1.220485] gpio-of-helper ocp:cape-universal: Allocated GPIO id=40 > [ 1.220631] gpio-of-helper ocp:cape-universal: Allocated GPIO id=41 > [ 1.220785] gpio-of-helper ocp:cape-universal: Allocated GPIO id=42 > [ 1.220933] gpio-of-helper ocp:cape-universal: Allocated GPIO id=43 > [ 1.221079] gpio-of-helper ocp:cape-universal: Allocated GPIO id=44 > [ 1.221210] gpio-of-helper ocp:cape-universal: Allocated GPIO id=45 > [ 1.221221] gpio-of-helper ocp:cape-universal: ready > END thanks you for your time regards, Sebastián On Tuesday, April 3, 2018 at 8:31:08 PM UTC-3, RobertCNelson wrote: > > On Tue, Apr 3, 2018 at 5:11 PM, Sebastián Sáez <otr...@gmail.com > <javascript:>> wrote: > > thank!, I do the cmd but now the linux is not booting > > > > this is the serial log > >>> > >>> U-Boot SPL 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29) > >>> > >>> Trying to boot from MMC1 > >>> > >>> > >>> > >>> U-Boot 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29 -0600), > Build: > >>> jenkins-github_Bootloader-Builder-32 > >>> > >>> > >>> CPU : AM335X-GP rev 2.1 > >>> > >>> I2C: ready > >>> > >>> DRAM: 512 MiB > >>> > >>> No match for driver 'omap_hsmmc' > >>> > >>> No match for driver 'omap_hsmmc' > >>> > >>> Some drivers were not found > >>> > >>> Reset Source: Power-on reset has occurred. > >>> > >>> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > >>> > >>> Using default environment > >>> > >>> > >>> Board: BeagleBone Black > >>> > >>> <ethaddr> not set. Validating first E-fuse MAC > >>> > >>> BeagleBone Black: > >>> > >>> Model: SeeedStudio BeagleBone Green Wireless: > >>> > >>> BeagleBone: cape eeprom: i2c_probe: 0x54: > >>> > >>> BeagleBone: cape eeprom: i2c_probe: 0x55: > >>> > >>> BeagleBone: cape eeprom: i2c_probe: 0x56: > >>> > >>> BeagleBone: cape eeprom: i2c_probe: 0x57: > >>> > >>> Net: eth0: MII MODE > >>> > >>> Could not get PHY for cpsw: addr 0 > >>> > >>> cpsw, usb_ether > >>> > >>> Press SPACE to abort autoboot in 2 seconds > >>> > >>> board_name=[A335BNLT] ... > >>> > >>> board_rev=[GW1A] ... > >>> > >>> switch to partitions #0, OK > >>> > >>> mmc0 is current device > >>> > >>> SD/MMC found on device 0 > >>> > >>> ** Bad device 0:2 0x82000000 ** > >>> > >>> ** Bad device 0:2 0x82000000 ** > >>> > >>> switch to partitions #0, OK > >>> > >>> mmc0 is current device > >>> > >>> Scanning mmc 0:1... > >>> > >>> gpio: pin 56 (gpio 56) value is 0 > >>> > >>> gpio: pin 55 (gpio 55) value is 0 > >>> > >>> gpio: pin 54 (gpio 54) value is 0 > >>> > >>> gpio: pin 53 (gpio 53) value is 1 > >>> > >>> switch to partitions #0, OK > >>> > >>> mmc0 is current device > >>> > >>> gpio: pin 54 (gpio 54) value is 1 > >>> > >>> Checking for: /uEnv.txt ... > >>> > >>> Checking for: /boot.scr ... > >>> > >>> Checking for: /boot/boot.scr ... > >>> > >>> Checking for: /boot/uEnv.txt ... > >>> > >>> gpio: pin 55 (gpio 55) value is 1 > >>> > >>> 1867 bytes read in 43 ms (42 KiB/s) > >>> > >>> Loaded environment from /boot/uEnv.txt > >>> > >>> Checking if uname_r is set in /boot/uEnv.txt... > >>> > >>> gpio: pin 56 (gpio 56) value is 1 > >>> > >>> Running uname_boot ... > >>> > >>> loading /boot/vmlinuz-4.4.125-bone22 ... > >>> > >>> 8506344 bytes read in 587 ms (13.8 MiB/s) > >>> > >>> uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot.dtb] ... > >>> > >>> uboot_overlays: Switching too: dtb=am335x-boneblack-uboot.dtb ... > >>> > >>> loading /boot/dtbs/4.4.125-bone22/am335x-boneblack-uboot.dtb ... > >>> > >>> 50339 bytes read in 79 ms (622.1 KiB/s) > >>> > >>> uboot_overlays: [fdt_buffer=0x60000] ... > >>> > >>> uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ... > >>> > >>> 1440 bytes read in 179 ms (7.8 KiB/s) > >>> > >>> uboot_overlays: loading /lib/firmware/BB-BBGW-WL1835-00A0.dtbo ... > >>> > >>> 4839 bytes read in 69 ms (68.4 KiB/s) > >>> > >>> failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND > >>> > >>> uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ... > >>> > >>> 711 bytes read in 219 ms (2.9 KiB/s) > >>> > >>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC > >>> > >>> failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > >>> > >>> base fdt does did not have a /__symbols__ node > >>> > >>> make sure you've compiled with -@ > >>> > >>> uboot_overlays: loading /lib/firmware/AM335X-PRU-UIO-00A0.dtbo ... > >>> > >>> 883 bytes read in 162 ms (4.9 KiB/s) > >>> > >>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC > >>> > >>> failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > >>> > >>> base fdt does did not have a /__symbols__ node > >>> > >>> make sure you've compiled with -@ > >>> > >>> uboot_overlays: loading /lib/firmware/univ-bbgw-EW-00A0.dtbo ... > >>> > >>> 82622 bytes read in 89 ms (906.3 KiB/s) > >>> > >>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC > >>> > >>> failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > >>> > >>> base fdt does did not have a /__symbols__ node > >>> > >>> make sure you've compiled with -@ > >>> > >>> loading /boot/initrd.img-4.4.125-bone22 ... > >>> > >>> 5415890 bytes read in 392 ms (13.2 MiB/s) > >>> > >>> debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 > >>> root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M > >>> net.ifnames=0 quiet] ... > >>> > >>> debug: [bootz 0x82000000 0x88080000:52a3d2 88000000] ... > >>> > >>> ERROR: Did not find a cmdline Flattened Device Tree > >>> > >>> Could not find a valid device tree > > Okay that was weird, i'll retest that tomorrow at work.. > > 4.4.125-bone22 + u-boot overlays should work.. > > <weird> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > base fdt does did not have a /__symbols__ node > make sure you've compiled with -@ > </end> > > They were compiled with -@ wonder what failed... > > Regards, > > -- > Robert Nelson > https://rcn-ee.com/ > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/4e3a4e44-989c-4860-a90d-28f2da6ced64%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
